Lockwasher DIN 5406 Type MB 12 inner diameter 60mm
Material: Steel, min. strength 350 N/mm2.Safety plates for locknuts DIN 981.A keyway is required on the shaft thread.
Article ID: 65367101

Spur gear made of stainless steel 1.4305 with hub module 3.18 (metrical pitch 10mm) 20 teeth tooth width 25mm
Article ID: 21099020

Locking assembly COM-B bore 7mm size 7-15 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577607

Interface/connection dim's : DN80 acc. EN 1092-1 PN16
SFN-080-IF-07E-HT-F1m-S-B-B
SKU: SSFN008038
Stock *: 0
No of bars: 7
Build-in length: 297 mm
Weight: 21 kg
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 200mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150200

Detachable trunnion mounting (front or rear) for cylinder diameter 50mm
Materials: Mounting: Grey cast iron. Screws: Steel, zinc plated. Mounting element at the bearing or at the end cover.

Article ID: 81001350

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.5-16 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Flat suction cup, oval, Silicone material, »SGO«, Ø30x10 suitable connection nipple IT G 1/8, suitable connection nipple ET G 1/8
Robust and hard-wearing suction pad with a single, oval-shaped sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to handle long or flat workpieces. Due to its oval shape, it has a considerably higher suction force than round, flat suction pads when handling narrow or long workpieces.
It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Higher suction force for narrow workpiecesSupports on the bottomHigh suction force in spite of small dimensions

Applications:
Handling narrow workpieces and stripsHandling workpieces with only a small, narrow gripping surface

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 10x8 mm, PN at 23 °C max. 7 bar, green, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Foot fastening, Aluminium flat profile, for piston rod-free cylinder, Piston Ø 63, 1 piece with 2 screws
Foot model

Screw-in fitting, Aluminium / plastic, for PVC pneumatic hose 10.2x8, G 1/2, Temperature -15 °C to 70 °C, PN -0.95 - 15 bar

Replacement blade (1 piece)

Throttle check valve, Discharge throttle (»C«) quick connector Hose 6/4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Angled screw-in supports, R 1/2 o., for hose I.D. 8 mm, AF 22, Over-pressure max. 22 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Lockwasher DIN 5406 MB12 zinc plated inner diameter 60mm
Material: Steel zinc-plated, min. strength 350 N/mm2.Safety plates for locknuts DIN 981. A keyway is required on the shaft thread.
Article ID: 65367181

Locking assembly COM-B bore 8mm size 8-15 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577608

Interface/connection dim's : DN100 acc. EN 1092-1 PN16
SFN-100-IF-07E-HT-F1m-S-B-B
SKU: SSFN010038
Stock *: 0
Magnet quality: Neodymium GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 150 °C
No of bars: 7
Build-in length: 300 mm
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 250mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150250

Precision worm wheel centre distance 50mm i=8.66 26 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33000800

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.1 - 1 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Angled piece, exterior / exterior, R 1/8, Operating pressure max. 150 bar, Operating temp. -20°C to 150°C, Stainless steel 1.4404

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 10x8 mm, PN at 23 °C max. 7 bar, silver, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Storz reducer, Aluminium, Storz size 52-C/25-D, Tappet distance 66/31 mm, Operating pressure max. 16 bar, Temp. -40 °C to 110 °C
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Mini ball valve »valve line«, nickel-plated brass, Rotating handle, Medium/ambient temp. -10°C to 90°C, G 1/4 IT/ET, PN max 10 bar

Angled screw-in fitting G 1/6 o., for hose 4/8 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 5/3, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Angled screw-in supports, R 1/2 o., for hose I.D. 12 mm, AF 22, Over-pressure max. 22 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Spur gear made of polyacetal resin die-cast with hub module 0.7 28 teeth tooth width 6mm outside diameter 21mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28202800

Locking assembly COM-B bore 9mm size 9-16 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577609

Interface/connection dim's : DN125 acc. EN 1092-1 PN16
SFN-125-IF-07E-HT-F1m-S-B-B
SKU: SSFN012538
Stock *: 0
Magnet quality: Neodymium GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 150 °C
No of bars: 7
Build-in length: 300 mm
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

K15A General features
Cable composition:– 0.55 mm² conductors.– Self-adjusting conductive core.– Polyolefin insulating sheath.– Braided copper sheath.– Outer sheath in modified polyolefin.
Minimum room temperature withstood -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Maximum length of the heating circuit from the supply point 110 m
Electric features
Power supply 230V-50Hz
Power delivered ~15W/m at 5°C
Calibration of the protection circuit 16A x 100 mt at 0°C

Spur gear made of plastic PA12G with steel core module 1.5 80 teeth tooth width 17mm outside diameter 123mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 21855080

Precision worm wheel centre distance 50mm i=23 23 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33002300

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.1 - 2 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Straight reducer, Pipe exterior Ø Female connector 14/12 mm, PN max. 630 bar, a/f1 24, a/f2 27, a/f3 24, galvanised steel
Straight reducers, heavy type

PVC braided hose, Temperature -15 °C to 60 °C, Hose Ø 16x10, PN at 23 °C max. 15 bar air, 20 bar fluids, Roll of 25 m
Flexible, pressure-resistant and non-abrasive standard hose for a wide range of applications in industry, machinery and plant construction, commerce, manual trades and laboratories.

- Complies with EU Regulation No. 10/2011 regarding contact with food, simulants A, B, C
- Good chemical resistance when gaseous or liquid media are conveyed
- Use of high-quality materials guarantees enhanced durability and UV protection

Straight push-in bulkhead connector, M11x0.75, for hose exterior Ø 4 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Mini ball valve »valve line«, nickel-plated brass, Rotating handle, Medium/ambient temp. -10°C to 90°C, G 3/8 IT/ET, PN max 10 bar

Screw-on hose connector, G 3/8 i., for hose I.D. 10 mm, AF 19, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Push-in Y-fitting »Blue Series«, rotating, G 1/2 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Reducing nipple, Short design, M5 ET, M3 IT, AF 7, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Locking assembly COM-B bore 10mm size 10-16 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577610

Interface/connection dim's : DN100 acc. EN 1092-1 PN16
SFNG-100-IF-07E-HT-F1M-S-B-B
SKU: SSFNG10038
Stock: 1
No of bars: 7
Build-in length: 350 mm
Weight: 50 kg
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

K20A, K30A, K40A General features
Cable composition:– 1.25 mm² conductors– Self-adjusting conductive core– Polyolefin insulating sheath– Braided copper sheath– Outer sheath in modified polyolefin
Minimum installation room temperature -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Cable dimensions– 12.6 x 4.8 mm series K20A– 14.6 x 4.8 mm series K30A-K40A
Electric features
Power supply 230V-50Hz
Tolerance -0/+5 W
Power delivered– K20A 20 W/m at 10°C– K30A 30 W/m at 10°C– K40A 40 W/m at 10°C

Flanged bush BBP bore 10mm polyamide 6.6 outer diameter 12mm length 6mm flange diameter 16mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62381100

Ball head precision levelling adjuster MN 686.4 50-26.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699460

Precision worm wheel centre distance 53mm i=6.67 20 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, as besides the lead angle, also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 32300600

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.2 - 4 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Straight reducer, Pipe exterior Ø Female connector 20/10 mm, PN max. 400 bar, a/f1 32, a/f2 36, a/f3 22, galvanised steel
Straight reducers, heavy type

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 32, Stroke 55, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Push-in L-connector »metallica«, for hose exterior Ø 16 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 150 °C
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Mini ball valve »valve line«, nickel-plated brass, Rotating handle, Medium/ambient temp. -10 °C to 90 °C, G 3/8 IT, PN max. 10 bar

Bracket 90, 90°, Rp 1 1/4 IT, Rp 1 1/4 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in Y-fitting »Blue Series«, rotating, R 1/2 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Hose sleeve, ball nipple, hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Locking assembly COM-B bore 11mm size 11-18 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577611

Interface/connection dim's : DN150 acc. EN 1092-1 PN16
SFNG-150-IF-09E-HT-F1M-S-B-B
SKU: SSFNG15038
Stock *: 0
No of bars: 9
Build-in length: 410 mm
Weight: 74 kg
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

K15A General features
Cable composition:– 0.55 mm² conductors.– Self-adjusting conductive core.– Polyolefin insulating sheath.– Braided copper sheath.– Outer sheath in modified polyolefin.
Minimum room temperature withstood -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Maximum length of the heating circuit from the supply point 110 m
Electric features
Power supply 230V-50Hz
Power delivered ~15W/m at 5°C
Calibration of the protection circuit 16A x 100 mt at 0°C