T screw-in fitting, R 1/8 o., for hose 6/4 mm, AF 12/10, Pressure range max. 25 bar, Temp. -40 °C to 200 °C Stainless steel 1.4404
Supplied without seals. For use with corrosive media and at high temperatures.

Screw fitting series made of stainless steel for all applications where compliance with strict tightness, pressure and temperature requirements is essential.
The parts are manufactured without rubber seals, in other words they are ideal for very high temperatures or for use with corrosive liquids, e.g. in cases when FPM is no longer suitable.

Push-in bulkhead L-connector »Blue Series« mini, M8x0.75, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

T screw on distributor, G 1/8, AF 17, Brass

Throttle check valve, Discharge throttle (»C«) threaded connection M5 i., M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Screw-in hose connector, M5 o., for hose I.D. 3 mm, AF 7, brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Locking assembly COM-A bore 30mm size 30-55 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577530

Product inlet/outlet size : #240 mm
SECD-2424-08P-N-F1H-B-P-B-E
SKU: SECD240012
Stock: 0
Max. capacity: 30 m³/h
No of bars: 8 (4+4)
Build-in length: 220 mm
For magnetic filtering of small amounts of ferrous contaminants from dusty, free-flowing powders in free-fall transport pipes.The automatic cleaning makes this type suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.Industrial finish - grit blasting Ra 3 µm

Automatic cleaning (discontinuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø25 mm, 11,000 gauss)
Dust-proof
ATEX II 1/2 D

Application

Dusty powders in free-fall pipes

These automatic, discontinuously cleaning, dust-proof Cleanflows are especially suitable for dusty powders with a small amount of ferrous impurities.
 
Also suitable for non-dusty powders & granulates, but NOT for sticky powders that cause blockages. For those applications the rotating versions of this type Cleanflows are a better solution.
 
The automatic cleaning makes them suitable for badly accessible situations.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids with Ø25 magnetic bars, placed staggered one above the other
Pneumatic bar and valve movement
Magnet quality: neodymium N-42, 11,000 gauss on the tube
Dust-proof housing
Material housing: AISI304 / AISI316(L)
Finish: grit blasting
Material gaskets/seals: Silicone EC1935 / FDA


Options

Available accessories & options

Online available accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Available options

Integrated valve box for ferrous particles disposal
(our advice: always order with corresponding valve box for trouble-free operation)
Iron discharge cycle control:

Pneumatic control -> start by local push button
Siemens LOGO! PLC control -> start by local push button or from control room


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, air pressure automatically pushes the magnets out within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence

Stop the product stream
Give start signal to the magnet's control unit

Now first the valve in the valve box is automatically switched to iron discharge position
Then the magnets inside the pneumatic tubes are moved automatically out of the product channel
The captured metal particles want to 'travel' with the magnets, but are held by retainer rings on the magnet bar tubes. As soon as the magnets are out of reach, the captured particles automatically drop off of the tubes, into the valve box, where they are discharged further
Then the magnets inside the pneumatic tubes are moved automatically back into the product channel
When the magnets are all back in, the valve will automatically be switched back to its production position
As soon as the magnets and valve are back in production position, the control will give a 'ready for production' signal
You can now safely resume production

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Slide set DS 0330 slide length 300mm stainless steel
Material: Stainless steel 1.4301. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Can be mounted on both sides. Service life 10,000 / 80,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load rating.

Article ID: 64944630

Precision worm wheel centre distance 53mm i=4.75 19 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, as besides the lead angle, also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 32300400

5/2-way valve, Pneumatic, bistable, Connection G 1/2, DN 15, Operating pre. 1 to 10 bar, Operating temp. -10 °C to 60 °C

Distributor strip, Outlets both sides, front and back, Input 2 x 1/4, Output 4 + 4 x 1/8, Aluminium
For easy assembly of compressed air taps (screw fittings, unions, couplings, etc.).
Optionally with 2, 3, 4, or 6 outlets on one side or both sides.

Mist oiler »multifix«, Metal container, Viewing tube, Size 1, G 1/4, Input pressure max. 20 bar, Medium / ambient temp. max. 60 °C
Proportional lubricators, oil can be filled under pressure.

L screw-in fitting, R 1/8 o., for hose 6/4 mm, AF 12/10, Pressure range max. 25 bar, Temp. -40 °C to 200 °C Stainless steel 1.4404
Supplied without seals. For use with corrosive media and at high temperatures.

Screw fitting series made of stainless steel for all applications where compliance with strict tightness, pressure and temperature requirements is essential.
The parts are manufactured without rubber seals, in other words they are ideal for very high temperatures or for use with corrosive liquids, e.g. in cases when FPM is no longer suitable.

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M12x1.5 i., Pipe ext. Ø 6, PN max. 315 bar, galvanised steel

Pipe double nipple 23, ET/ET, Black steel, R 1 1/4, Length 40.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Mini ball valve, Smooth surface, nickel-plated brass, Medium temp.-10°C to 70°C (short term 90 °C), G 3/4 IT, DN13.5 PN max.10 bar

Screw-in hose connector, M5 o., for hose I.D. 4 mm, AF 7, brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Locking assembly COM-A bore 32mm size 32-60 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577532

Product inlet/outlet size : #320 mm
SECD-3232-11P-N-F1H-B-P-B-E
SKU: SECD320012
Stock: 0
Max. capacity: 60 m³/h
No of bars: 11 (5+6)
Build-in length: 220 mm
For magnetic filtering of small amounts of ferrous contaminants from dusty, free-flowing powders in free-fall transport pipes.The automatic cleaning makes this type suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.Industrial finish - grit blasting Ra 3 µm

Automatic cleaning (discontinuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø25 mm, 11,000 gauss)
Dust-proof
ATEX II 1/2 D

Application

Dusty powders in free-fall pipes

These automatic, discontinuously cleaning, dust-proof Cleanflows are especially suitable for dusty powders with a small amount of ferrous impurities.
 
Also suitable for non-dusty powders & granulates, but NOT for sticky powders that cause blockages. For those applications the rotating versions of this type Cleanflows are a better solution.
 
The automatic cleaning makes them suitable for badly accessible situations.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids with Ø25 magnetic bars, placed staggered one above the other
Pneumatic bar and valve movement
Magnet quality: neodymium N-42, 11,000 gauss on the tube
Dust-proof housing
Material housing: AISI304 / AISI316(L)
Finish: grit blasting
Material gaskets/seals: Silicone EC1935 / FDA


Options

Available accessories & options

Online available accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Available options

Integrated valve box for ferrous particles disposal
(our advice: always order with corresponding valve box for trouble-free operation)
Iron discharge cycle control:

Pneumatic control -> start by local push button
Siemens LOGO! PLC control -> start by local push button or from control room


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, air pressure automatically pushes the magnets out within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence

Stop the product stream
Give start signal to the magnet's control unit

Now first the valve in the valve box is automatically switched to iron discharge position
Then the magnets inside the pneumatic tubes are moved automatically out of the product channel
The captured metal particles want to 'travel' with the magnets, but are held by retainer rings on the magnet bar tubes. As soon as the magnets are out of reach, the captured particles automatically drop off of the tubes, into the valve box, where they are discharged further
Then the magnets inside the pneumatic tubes are moved automatically back into the product channel
When the magnets are all back in, the valve will automatically be switched back to its production position
As soon as the magnets and valve are back in production position, the control will give a 'ready for production' signal
You can now safely resume production

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Neoprene timing belt 56 MXL 012 70 teeth Lw 142.24mm belt width 3.2mm
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile MXL = 0,08" = 2.032 mm. Belt width 012 = 3.2mm. Temperature range -20º to +100ºC.
Article ID: 18162000

Flange bearing unit FK 20 bore 20mm material steel nickel plated
Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearings from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the fixed side. With two angular contact ball bearings, lightly preloaded, with seals. Types FK06 and FK08 sealed only on the cylindrical side. With 4 mounting holes. Locknut and distance bushes are included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for support side: Flange Bearing FF. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201520

2/2-way solenoid valve »2S«, Stainless steel, NC, pilot operated, 230 V, 50 Hz, Medium temp. max. 80°C/90°C, G 1, PN 0.5 - 10 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Straight push-in fitting, Exterior hexagonal, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar, Stainless steel
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

2/2-way solenoid valve »2S«, Stainless steel, NC, directly operated, 24 V DC, Medium temp. max. 80 °C/90 °C, G 1/2, PN 0 - 30 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

T screw-in fitting, R 1/4 o., for hose 6/4 mm, AF 12/10, Pressure range max. 25 bar, Temp. -40°C to 200°C, Stainless steel 1.4404
Supplied without seals. For use with corrosive media and at high temperatures.

Screw fitting series made of stainless steel for all applications where compliance with strict tightness, pressure and temperature requirements is essential.
The parts are manufactured without rubber seals, in other words they are ideal for very high temperatures or for use with corrosive liquids, e.g. in cases when FPM is no longer suitable.

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M18x1.5 i., Pipe ext. Ø 12, PN max. 315 bar, galvanised steel

Pipe double nipple 23, ET/ET, Black steel, R 1 1/4, Length 200.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Screw plug for bite-type tube fitting, Pipe exterior Ø 14 mm, PN max. 630 bar
Screw plug, heavy type

Hexagonal counter nut, M12x0.75, nickel-plated brass
Accessories 2/2-way toggle valves

Miniature worm gear motor SFS Gr. 2 with DC-motor 12V i=62:1 idle speed 25 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047012

Ready-to-install flange nut Tr.28 x 5 single-start right material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Single-Thread, right handTolerance zone 7H.
Article ID: 64477128

Locking assembly COM-A bore 35mm size 35-60 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577535

Product inlet/outlet size : #400 mm
SECD-4040-14P-N-F1H-B-P-B-E
SKU: SECD400012
Stock: 0
Max. capacity: 90 m³/h
No of bars: 14 (7+7)
Build-in length: 220 mm
For magnetic filtering of small amounts of ferrous contaminants from dusty, free-flowing powders in free-fall transport pipes.The automatic cleaning makes this type suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.Industrial finish - grit blasting Ra 3 µm

Automatic cleaning (discontinuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø25 mm, 11,000 gauss)
Dust-proof
ATEX II 1/2 D

Application

Dusty powders in free-fall pipes

These automatic, discontinuously cleaning, dust-proof Cleanflows are especially suitable for dusty powders with a small amount of ferrous impurities.
 
Also suitable for non-dusty powders & granulates, but NOT for sticky powders that cause blockages. For those applications the rotating versions of this type Cleanflows are a better solution.
 
The automatic cleaning makes them suitable for badly accessible situations.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids with Ø25 magnetic bars, placed staggered one above the other
Pneumatic bar and valve movement
Magnet quality: neodymium N-42, 11,000 gauss on the tube
Dust-proof housing
Material housing: AISI304 / AISI316(L)
Finish: grit blasting
Material gaskets/seals: Silicone EC1935 / FDA


Options

Available accessories & options

Online available accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Available options

Integrated valve box for ferrous particles disposal
(our advice: always order with corresponding valve box for trouble-free operation)
Iron discharge cycle control:

Pneumatic control -> start by local push button
Siemens LOGO! PLC control -> start by local push button or from control room


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, air pressure automatically pushes the magnets out within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence

Stop the product stream
Give start signal to the magnet's control unit

Now first the valve in the valve box is automatically switched to iron discharge position
Then the magnets inside the pneumatic tubes are moved automatically out of the product channel
The captured metal particles want to 'travel' with the magnets, but are held by retainer rings on the magnet bar tubes. As soon as the magnets are out of reach, the captured particles automatically drop off of the tubes, into the valve box, where they are discharged further
Then the magnets inside the pneumatic tubes are moved automatically back into the product channel
When the magnets are all back in, the valve will automatically be switched back to its production position
As soon as the magnets and valve are back in production position, the control will give a 'ready for production' signal
You can now safely resume production

EV70D Telecontrol General features
Instrument customisable via PC for all parameters.
Extractable terminal block for fast replacement of the instrument.
2-line display for setting parameters, remote monitoring and management for both GSM modem ( mobile telephony) and PSTN modem ( fixed telephony)
Mounted on DIN rail ( 9 modules)
Electric features
Absorption 10VA
8 digital inputs ON- OFF
4 analog inputs, via detection probes
4 output relays
Contact rating 5A- 230Vac ( ohmic charge).

Spur gear made of polyketone die-cast with hub module 0.7 25 teeth tooth width 6mm outside diameter 18,9mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28202501

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 25mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150025

2/2-way solenoid valve »2S«, Stainless steel, NC, pilot operated, 24 V DC, Medium temp. max. 80 °C / 90 °C, G 1, PN 0.5 - 10 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Filter »inline«, 36 µm, G 1/8 interior / interior, AF 17, Input pressure max. 18 bar, Temp. range 0 °C to 80 °C, Housing: Brass
For integration in a pneumatic system if different system sections or tools require different air qualities.

2/2-way solenoid valve »2S«, Stainless steel, NC, directly operated, 230 V, 50 Hz, Medium temp. max. 80°C/90°C, G 1/2, PN 0-30 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

L screw-in fitting, R 1/4 o., for hose 6/4 mm, AF 12/10, Pressure range max. 25 bar, Temp. -40°C to 200°C, Stainless steel 1.4404
Supplied without seals. For use with corrosive media and at high temperatures.

Screw fitting series made of stainless steel for all applications where compliance with strict tightness, pressure and temperature requirements is essential.
The parts are manufactured without rubber seals, in other words they are ideal for very high temperatures or for use with corrosive liquids, e.g. in cases when FPM is no longer suitable.

Male elbow, NPT 1/8 o., Pipe exterior Ø 6 mm, PN max. 100 bar, a/f1 12, a/f2 9, galvanised steel
Male elbow, NPT thread, very light type

Push-in T-connector, Plug nipple »Blue Series«, for hose and plug exterior Ø 6 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 4/2.5, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Y reducing supports, for hose I.D. 6/8/6 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Miniature worm gear motor SFS Gr. 2 with DC-motor 24V i=62:1 idle speed 35 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047024

Ready-to-install flange nut Tr.28 x 5 single-start left material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Single-Thread, left handTolerance zone 7H.
Article ID: 64477428

Locking assembly COM-A bore 38mm size 38-65 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577538

Product inlet/outlet size : #240 mm
SECC-2424-05S-N-Ex-F1E-L-B-B
SKU: SECC240201
Stock: 1
Max. capacity: 30 m³/h
No of bars: 5 (2+3)
Weight: 100 kg
This unique Cleanflow type discharges the filtered ferrous contaminants during production. So no production stop is required. The time-interval controlled discharge of ferrous particles makes it suitable for product streams with relatively much ferrous contamination.Suitable for granulates and dry, free-flowing powders in free-fall transport pipes.The automatically controlled discharging of captured ferrous particles makes this type of Cleanflows suitable for places where they are hardly or not accessible for operation.

Automatic cleaning (continuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø34 mm, 9400 gauss)
Capacity 30 - 90 m³/h
ATEX II 1/2 D

Application

Powders & granulates with relatively much ferrous impurities

Suitable for granulates and free-flowing powders with relatively large amounts of ferrous contaminations in non-pressurized free-fall pipes.
 
Due to the automated contral and operation they are suitable for less easily accessible situations and / or centrally managed controls.
 
Not suitable for:

When product loss is unacceptable. During a cleaning cycle some product might flow out of the product channel, together with the caught magnetic particles.
Poorly flowing sticky / fatty powders that cause clogging. For those applications the rotating versions of these Cleanflows are a better solution.


Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
These automatic Cleanflow magnetic separators have 2 magnetic grids, placed staggered one above the other. They contain pneumatic magnetic bars, constructed of robust Ø34 mm SS tubes inside of which strong neodymium N42 magnet packages are moved by air pressure. The bars measure no less than 9400 gauss on the Ø34 mm tubes.
 
Summary of important specifications

Siemens LOGO! PLC control
Ø34 mm pneumatic operated magnetic bars
Magnet quality: neodymium N-42, 9400 gauss on the Ø34 mm tube
Material housing and magnetic bars: AISI304 / AISI316(L)
Finish: grit blasted
Material gaskets: PA6G acc. EC1935 / FDA


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Options

Version suitable for high temperatures up-to 120°C (not available for ATEX II 1/2D versions)
Magnetic bars end position detection (not available for ATEX II 1/2D versions)


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?

Production can continue during cleaning, because the magnetic bars of these Cleanflows are horizontally fixed inside the product channel. As a result, magnetic contaminants can never pass.
The pneumatic tubes enclosing the magnetic bars are horizontally fixed positioned in both the product channel and - in turn - in the left and right side chutes for iron particle discharging.
After you have given the start signal for an iron particle discharge cycle, the tubes slide over the magnets by air pressure to the left or right iron discharging chute. 
The retainer rings on the tubes hereby drag the trapped ferrous particles out of the product channel. Once outside the product channel, the ferrous particles fall off the tubes as soon as they are outside the influence of the magnets.
The time interval between 2 iron particles discharge cycles can be set locally, on the PLC control on the machine, or from your central control.

ECC250LOG General features
Datalogger with webserver interface.
Manages up to 250 M-Bus meters.
4 GB internal memory provides a historic up to 10 years.
Meter data acquisition interval of 15 min to 1 month.
Meters reading, report sending, system remote management
LED display 128×96 pixels for local consultation and confguration.
With IO for logical management and remote control.
Temperature range: operative: -10° … +55°C.
Temperature storage: -25° … +65°C.
Dimensions 90x71x62 mm
Electric features
Power supply: 24 Vdc ± 10%, 24 Vac (min 20Vac, max 40Vac).
Consumption: 3W.

Hexagon nut DIN 6330 steel strength 10 thread M6 right hand
Material: Heat-treated steel, tensile strength 10, shape B. With round contact surface at one end. The round end matches the spherical washers DIN 6319. This combination can be used to compensate bearing displacement.

Article ID: 65320600

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 50mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150050

Rod end BR DIN 12240-4 series K external tread M24x2 right with spherical ball bearing
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Thread rolled., Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63252500

Round cylinder, double-acting, with magnet, Piston Ø 50, Stroke 250, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Version with magnetic piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Filter »inline«, 36 µm, G 1/8 interior / exterior, AF 17, Input pressure max. 18 bar, Temp. range 0 °C to 80 °C, Housing: Brass
For integration in a pneumatic system if different system sections or tools require different air qualities.

2/2-way solenoid valve »2S«, Stainless steel, NC, directly operated, 230 V, 50 Hz, Medium temp. max. 80°C/90°C, G 3/8, PN 0-30 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Screw-in hose connector, G 1 1/2 o., for hose I.D. 32 mm, AF 55, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Straight reducer, Pipe exterior Ø Female connector 12/6 mm, PN max. 315 bar, a/f1 19, a/f2 22, a/f3 14, galvanised steel
Straight reducers, light type