Neodymium (NdFeB) 25 N
PM-TE-N-SG-D10x4.5xM4x8
SKU: GM17622
Stock: 156
Size: 10 mm
Thread (M): M4
Compact magnet systems with a steel shell and with a threaded end for easy mounting. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded end are available in various sizes in neodymium and ferrite.

Available in various qualities
Easy to install
Deliverable from stock

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

magnetic field detector
The magnetic detector MD 120 serves for the contactless detection of a magnetic field. The switching characteristics were matched to those magnetic sensors of the M120 series. Operating distance 120 mm permanent magnet M4.0.

magnetic field detector
The magnetic detector MD 90 serves for the contactless detection of a magnetic field. The switching characteristics were matched to those magnetic sensors of the M90 ​​series. Operating distance of 90 mm on permanent magnet M4.0.

Damping magnet for magnetic sensors

With internal bore for mounting
Type: Ø 31 x 15 mm
Temperature range: -25 ° C to + 130 ° C
Material: barium

Damping magnet for magnetic sensors

Design: Ø 30 x 10 mm
Temperature range: -25 ° C to + 130 ° C
Material: barium

Damping magnet for magnetic sensors

With internal bore for mounting
Type: Ø 20 x 6.5 mm
Temperature range: -25 ° C to + 130 ° C
Material: barium

Damping magnet for magnetic sensors

Design: Ø 6 x 25 mm
Temperature resistance: -100 ° C to + 450 ° C
Material: Alnico

Damping magnet for magnetic sensors

Type: Ø 10 x 3 mm
Temperature resistance: -50 ° C to + 180 ° C
Material: cobalt Somarium

Neodymium (NdFeB) 60 N
PM-TE-N-SG-D13x4.5xM5x8
SKU: GM17623
Stock: 222
Size: 13 mm
Thread (M): M5
Compact magnet systems with a steel shell and with a threaded end for easy mounting. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded end are available in various sizes in neodymium and ferrite.

Available in various qualities
Easy to install
Deliverable from stock

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Neodymium (NdFeB) 40 N
PM-BA-N-BR-D10h6x20
SKU: GM17303
Stock: 32
Diameter: 10 mm
A: 8 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Neodymium (NdFeB) 800 N
PM-TI-N-SG-D50x10xM8
SKU: GM17440
Stock: 16
Diameter (D): 50 mm
Height: 10 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a cylinder hole for easy mounting. These pot magnets are screwable at a high torque while the magnet remains unloaded. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with cylinder hole are available in various sizes and grades such as neodymium and ferrite.

Deliverable from stock
Available in various qualities
Available with extra strong magnet
High torque screwable

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion. The cylinder hole makes the magnet system screwable with a high torque.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Screwable at a high torque

These pot magnets with cylinder hole are suitable for extra tightening. There is no force on the pot magnet itself. This is not a part of the screw connection. Mounting is easy with a cylinder head bolt.

Neodymium (NdFeB) 100 N
PM-RTE-N-RB-D43-6-M6-21
SKU: GM17518
Stock: 47
Size: Ø43 mm
Height (L): 12 mm
Shear force: 30 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Neodymium (NdFeB) 500 N
PM-TI-N-SG-D40x8xM5
SKU: GM17439
Stock: 298
Diameter (D): 40 mm
Height: 8 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a cylinder hole for easy mounting. These pot magnets are screwable at a high torque while the magnet remains unloaded. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with cylinder hole are available in various sizes and grades such as neodymium and ferrite.

Deliverable from stock
Available in various qualities
Available with extra strong magnet
High torque screwable

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion. The cylinder hole makes the magnet system screwable with a high torque.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Screwable at a high torque

These pot magnets with cylinder hole are suitable for extra tightening. There is no force on the pot magnet itself. This is not a part of the screw connection. Mounting is easy with a cylinder head bolt.

Neodymium (NdFeB) 250 N
PM-RTB-N-RB-D66x8.5xM5
SKU: GM17511
Stock: 0
Size: Ø66 mm
Height (L): 15 mm
Shear force: 85 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Neodymium (NdFeB) 140 N
PM-TB-N-SG-D20x6x13xM4
SKU: GM17605
Stock: 0
Diameter (D): 20 mm
Height (H): 6 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Neodymium (NdFeB) 160 N
PM-HS-N-SG-D25x7xd4.5/9
SKU: GM17427
Stock: 25
Holding force: 160 N
Height: 7 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and a countersunk hole for easy mounting. The bolt with a flat countersunk head falls flush with or in the top of the magnet. This optimizes the attracting surface of the pot magnet. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field.Pot magnets with countersunk hole are available in various sizes and types such as neodymium, ferrite and AlNiCo.

Available in various sizes
Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron - (NdFeB) - which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface is covered with a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium pot magnets have a maximum operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic force. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.
 

Important to know

Tension on the magnet

For pot magnets with a cylinder hole, the magnet has a countersunk hole. Tighten with caution. Excessive tightening causes magnetic splinters or cracks in the magnet.

Description : Magnetic field sensor
MAGNETIC FIELD SENSOR MK11
SKU: 65.0000045
Stock: 7
With the polarity indicator, you can determine the orientation of a magnetic field by measuring whether a magnetic pole is a magnetic North (N) or South (S) pole. Suitable for detecting stray magnetic fields in packaging, performing magnet polarity checks, testing coils and use during the assembly of electric motors. There are types of pole indicators for 2D or 3D measurement, analogue or digital.

Indicates direction of magnetic field
Deliverable from stock
Analogue or digital
Two or three dimensional

Hook bracket Magswitch 50 mm
HMS-HOOK BRACKET MAGSQUARE50mm
SKU: MS-8800008
Stock: 7
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Max. holding force : 675 N
HMS-MAGSQUARE165
SKU: MS-8100494
Stock: 62
Width: 31 mm
Depth: 48 mm
Welding magnets are used to temporarily secure steel objects in any desired position.Holding workpieces in place is often useful when welding, grinding or polishing.These switchable holding magnets are a quick and secure solution.

Switching: manual
Max. holding force: 4500 N
Magnet produces magnetic field on 3 sides

Application

Application of switchable welding magnets

Switchable welding magnets - or magnetic clamps - are ideal for quickly and temporarily positioning and securing steel workpieces.
This allows you to easily weld, grind or otherwise rework them.
Despite the powerful magnetic field - in 3 directions - when switched on, no residual magnetism remains after release.

Advantages

Switchable welding magnets have the following advantages:
they are compact;
they have a manually switchable magnetic field;
they can be used for many application;
they are magnetic on 3 sides;
they have a maximum holding force of 4,500 N.

Electrical proximity sensor REED contact - Normally open
SENSOR SME-8M-DS-24V-K-2,5-OE
SKU: 83.9900015
Stock: 56
Power supply: 24 V DC
Sensors and switches are designed for the control, safety and automation of our magnet systems. They are easy to build into our systems. To ensure the safety of our products, the most important sensors are often already built in. This is to guard against, for example, vibration or overheating. Some sensors are optional, for example, for detecting different switching positions (on/off).

Quality and reliability
ATEX II 1/2 D possible
Easily integrated

Vertical mount Vertical mount | Magswitch AR30
HMS-M/ME/AR30 VERTICAL MOUNT
SKU: MS-8800110
Stock: 3
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Description : Mechanical polarity indicator
POLE INDICATOR
SKU: GM1841002
Stock: 24
With the polarity indicator, you can determine the orientation of a magnetic field by measuring whether a magnetic pole is a magnetic North (N) or South (S) pole. Suitable for detecting stray magnetic fields in packaging, performing magnet polarity checks, testing coils and use during the assembly of electric motors. There are types of pole indicators for 2D or 3D measurement, analogue or digital.

Indicates direction of magnetic field
Deliverable from stock
Analogue or digital
Two or three dimensional

Pole shoe Magswitch AR30
KIT AR30 COMBO FLAT/PIPE POLES
SKU: MS-8800070
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Max. stack height : 45 mm
HSS-F-BA-073x029-0075-B
SKU: TBSP000075
Stock: 71
Width: 73 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Diameter : 18 mm
HEPM-EM-D018-011-SW
SKU: GM17801
Stock: 12
Max. holding force: 45 N
Interface/connection dim's: Threaded hole M3
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Ball mount Ball Ø28,5 mm | Magswitch AR30
HMS-M/ME/AR30 BALL MOUNT
SKU: MS-8800105
Stock: 5
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Length : 300 mm
MAGNET VIEWER 300x300
SKU: GM1890015
Stock: 7
Length: 300 mm
Width: 300 mm
With the magne-viewer, you can visualize the magnetic poles yourself: by placing the film on a magnet the areas with a high magnetic flux density become visible. This is caused by magnetic particles dissolved in a liquid that can move inside the film. The film becomes darker in areas with a high flux density.

Makes magnetic fields visible
Thickness 0.5 mm
Colour: green

Pole shoe Magswitch AR50
KIT AR50 COMBO FLAT/PIPE POLES
SKU: MS-8800071
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Taper bush Ø30 mm
CLAMP BUSH 2517-30
SKU: 1002.10000
Stock: 1
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Taper bush Ø40 mm
CLAMP BUSH 2517-40
SKU: 1002.10001
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Diameter : 25 mm
HEPM-EM-D025-020-SW
SKU: GM17802
Stock: 32
Max. holding force: 140 N
Interface/connection dim's: Threaded hole M4
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Diameter : 32 mm
HEPM-EM-D032-022-SW
SKU: GM17803
Stock: 35
Max. holding force: 230 N
Interface/connection dim's: Threaded hole M4
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Diameter : 40 mm
HEPM-EM-D040-025.5-SW
SKU: GM17804
Stock: 8
Max. holding force: 400 N
Interface/connection dim's: Threaded hole M5
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Diameter : 50 mm
HEPM-EM-D050-027-SW
SKU: GM17805
Stock: 26
Max. holding force: 700 N
Interface/connection dim's: Threaded hole M5
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Description : Electronic polarity indicator
POLE INDICATOR ELECTRONIC
SKU: GM1841001
Stock: 22
With the polarity indicator, you can determine the orientation of a magnetic field by measuring whether a magnetic pole is a magnetic North (N) or South (S) pole. Suitable for detecting stray magnetic fields in packaging, performing magnet polarity checks, testing coils and use during the assembly of electric motors. There are types of pole indicators for 2D or 3D measurement, analogue or digital.

Indicates direction of magnetic field
Deliverable from stock
Analogue or digital
Two or three dimensional

Diameter : 63 mm
HEPM-EM-D065-030-SW
SKU: GM17806
Stock: 12
Max. holding force: 1000 N
Interface/connection dim's: Threaded hole M8
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Max. stack height : 110 mm
HSS-F-BA-073x029-0140-B
SKU: TBSP000140
Stock: 23
Width: 73 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Max. holding force : 1800 N
HMS-MAGSQUARE400
SKU: MS-8100238
Stock: 6
Width: 42 mm
Depth: 64 mm
Welding magnets are used to temporarily secure steel objects in any desired position.Holding workpieces in place is often useful when welding, grinding or polishing.These switchable holding magnets are a quick and secure solution.

Switching: manual
Max. holding force: 4500 N
Magnet produces magnetic field on 3 sides

Application

Application of switchable welding magnets

Switchable welding magnets - or magnetic clamps - are ideal for quickly and temporarily positioning and securing steel workpieces.
This allows you to easily weld, grind or otherwise rework them.
Despite the powerful magnetic field - in 3 directions - when switched on, no residual magnetism remains after release.

Advantages

Switchable welding magnets have the following advantages:
they are compact;
they have a manually switchable magnetic field;
they can be used for many application;
they are magnetic on 3 sides;
they have a maximum holding force of 4,500 N.

Ferrite 100 mm
HRA-F-052x17-AA-0100-B-B
SKU: TBAA010001
Stock: 10
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Length : 140 mm
SVM-F-114x47-0140-B-F0E
SKU: SVMF010140
Stock *: 0
Type: VMF1
Advised max. installation height: 50-65 mm
Interface/connection dim's: Threaded hole M8 (2x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Diameter : 80 mm
HEPM-EM-D080-038-SW
SKU: GM17808
Stock: 10
Max. holding force: 2200 N
Interface/connection dim's: Threaded hole M8
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Max. stack height : 240 mm
HSS-F-BA-073x029-0270-B
SKU: TBSP000270
Stock: 42
Width: 73 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Diameter : 20 mm
HEPM-EP-D020-022-SW
SKU: GM17852
Stock: 11
Max. holding force: 40 N
Interface/connection dim's: Threaded hole M4
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Ferrite 200 mm
HRA-F-052x17-AA-0200-B-B
SKU: TBAA020001
Stock: 16
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite 100 mm
HRA-F-077x24-AA-0100-B-B
SKU: TBAA010002
Stock: 58
Width: 77 mm
Height: 24 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Door safety switch 1 NC/1 NO contact
CODED MAGN SWITCH XCS 5MTR TM
SKU: EITA042001
Stock *: 0
Power supply: 24 V DC
Sensors and switches are designed for the control, safety and automation of our magnet systems. They are easy to build into our systems. To ensure the safety of our products, the most important sensors are often already built in. This is to guard against, for example, vibration or overheating. Some sensors are optional, for example, for detecting different switching positions (on/off).

Quality and reliability
ATEX II 1/2 D possible
Easily integrated

Taperlock hub Ø105 mm
FILLING BUSH 2517-PM
SKU: 1002.20000
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Ferrite 100 mm
HRA-F-102x24-AA-0100-B-B
SKU: TBAA010003
Stock: 2
Width: 102 mm
Height: 24 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Spring plunger M8 | Fixed
HGA-PL-S- M08-M24-NR-RI
SKU: TPGC990009
Stock: 97
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Spring plunger M10 | Fixed
HGA-PL-S-M10-M24-NR-RI
SKU: TPGC990025
Stock: 2
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Spring plunger M12 | Fixed
HGA-PL-S-M12-M24-NR-RI
SKU: TPGC990032
Stock: 46
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Pole shoe Magswitch AR70
KIT AR70 COMBO FLAT/PIPE POLES
SKU: MS-8800072
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Ferrite 300 mm
HRA-F-052x17-AA-0300-B-B
SKU: TBAA030001
Stock *: 0
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Spring plunger M8 | Flexible
HGA-PL-S-M08-M24-RO-FL
SKU: TPGC990008
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Spring plunger M10 | Flexible
HGA-PL-S-M10-M24-RO-FL
SKU: TPGC990001
Stock: 184
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Spring plunger M12 | Flexible
HGA-PL-S-M12-M24-RO-FL
SKU: TPGC990003
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Max. stack height : 100 mm
HSS-F-BA-114x047-0140-B
SKU: TBSP020140
Stock: 7
Width: 114 mm
Sheet separators with ferrite magnets are suitable for separating sheets in the most common situations.

Permanent magnetic
For sheets up to 4 mm thick
Max. stacking height 490 mm
Steel enclosure
Ferrite magnet

Operation

Ferrite sheet separator operation

The magnetic field automatically forces the sheets apart and separates them. When the upper sheet is removed, the next one rises immediately.
To prevent malfunctions in fully automated production processes we recommend the use of a number of extra sheet separators.

Installation example 1

Corner installation

For optimum results, it is best to place two sheet separators at the corner(s) of stacks of large steel sheets.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 2

Installation across from each other

Sheet separators placed across from each other ensure that the sheets begin to ‘float’.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Installation example 3

Single-piece installation

For small sheets, it is best to place the sheet separator in the middle of the shortest side.
The arrows in the photo indicate the recommended direction of transport in which the sheets can best be carried off after separation.

Ferrite 400 mm
HRA-F-052x17-AA-0400-B-B
SKU: TBAA040001
Stock: 22
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite Weakening outfeed
HRA-F-052x17-AB-0300-B-B
SKU: TBAB030001
Stock *: 0
Width: 52 mm
Height: 17 mm
Length: 300 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Ferrite Weakening infeed
HRA-F-052x17-AC-0300-B-B
SKU: TBAC030001
Stock *: 0
Width: 52 mm
Height: 17 mm
Length: 300 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller