Push-in T-connector, Plug nipple 6 mm »Blue Series«, unequal, for hose exterior Ø 4 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 5/3, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

T reducing supports, for hose I.D. 8/6/8 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Miniature worm gear motor SFS Gr. 2 with DC-motor 24V i=62:1 idle speed 50 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047124

Locking assembly COM-A bore 40mm size 40-65 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577540

Product inlet/outlet size : #320 mm
SECC-3232-07S-N-Ex-F1E-L-B-B
SKU: SECC320201
Stock *: 0
Max. capacity: 60 m³/h
No of bars: 7 (3+4)
Weight: 145 kg
This unique Cleanflow type discharges the filtered ferrous contaminants during production. So no production stop is required. The time-interval controlled discharge of ferrous particles makes it suitable for product streams with relatively much ferrous contamination.Suitable for granulates and dry, free-flowing powders in free-fall transport pipes.The automatically controlled discharging of captured ferrous particles makes this type of Cleanflows suitable for places where they are hardly or not accessible for operation.

Automatic cleaning (continuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø34 mm, 9400 gauss)
Capacity 30 - 90 m³/h
ATEX II 1/2 D

Application

Powders & granulates with relatively much ferrous impurities

Suitable for granulates and free-flowing powders with relatively large amounts of ferrous contaminations in non-pressurized free-fall pipes.
 
Due to the automated contral and operation they are suitable for less easily accessible situations and / or centrally managed controls.
 
Not suitable for:

When product loss is unacceptable. During a cleaning cycle some product might flow out of the product channel, together with the caught magnetic particles.
Poorly flowing sticky / fatty powders that cause clogging. For those applications the rotating versions of these Cleanflows are a better solution.


Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
These automatic Cleanflow magnetic separators have 2 magnetic grids, placed staggered one above the other. They contain pneumatic magnetic bars, constructed of robust Ø34 mm SS tubes inside of which strong neodymium N42 magnet packages are moved by air pressure. The bars measure no less than 9400 gauss on the Ø34 mm tubes.
 
Summary of important specifications

Siemens LOGO! PLC control
Ø34 mm pneumatic operated magnetic bars
Magnet quality: neodymium N-42, 9400 gauss on the Ø34 mm tube
Material housing and magnetic bars: AISI304 / AISI316(L)
Finish: grit blasted
Material gaskets: PA6G acc. EC1935 / FDA


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Options

Version suitable for high temperatures up-to 120°C (not available for ATEX II 1/2D versions)
Magnetic bars end position detection (not available for ATEX II 1/2D versions)


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?

Production can continue during cleaning, because the magnetic bars of these Cleanflows are horizontally fixed inside the product channel. As a result, magnetic contaminants can never pass.
The pneumatic tubes enclosing the magnetic bars are horizontally fixed positioned in both the product channel and - in turn - in the left and right side chutes for iron particle discharging.
After you have given the start signal for an iron particle discharge cycle, the tubes slide over the magnets by air pressure to the left or right iron discharging chute. 
The retainer rings on the tubes hereby drag the trapped ferrous particles out of the product channel. Once outside the product channel, the ferrous particles fall off the tubes as soon as they are outside the influence of the magnets.
The time interval between 2 iron particles discharge cycles can be set locally, on the PLC control on the machine, or from your central control.

ZC3 General features
Cast iron valve body.
Bronze rotating sector valve shaped to obtain a very precise regulation.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure PN6.
Maximum operating temperature – 120°C.

Conical seat DIN 6319 diameter 28mm for bolt diameter 14mm steel hardened
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65551400

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 80mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150080

Rod end BR DIN 12240-4 series K external tread M24x2 left with spherical ball bearing
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Thread rolled., Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63257500

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.1 - 1 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

2/3 Tube fitting, G 1 3/4 x 38 mm, swivel nut, taper seat, lightweight type, Brass with a bare metal surface

2/2-way solenoid valve »2S«, Stainless steel, NC, directly operated, 24 V DC, Medium temp. max. 80 °C/90 °C, G 3/8, PN 0 - 30 bar
Standard series available in two different versions:

-Directly operated
-Pilot-operated

Connector socket, form A acc. to ISO 4400, for all valves with a G 3/8 or G 1/2 thread except valve types 3 and 4.
Special connector socket (similar to form B) for all valves with a G 1/8 or G 1/4 thread except valve types 3 and 4.
Medium temperature max. 80 °C when used with water or oils, max. 90 °C when used with air.

Filter »variobloc«, PC container, Size 1, G 1/4, Input pressure max. 16 bar, Med. / ambient temp. max. 50 °C, Manual bleeder valve
Centrifugal separators with a sintered filter element.
Filtration takes place in a 2-stage process comprising cyclone separation (condensate) and a PE filter element (particles).
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Straight reducer, Pipe exterior Ø Female connector 15/10 mm, PN max. 315 bar, a/f1 24, a/f2 27, a/f3 19, galvanised steel
Straight reducers, light type

Push-in T-connector, Plug nipple »Blue Series«, for hose and plug exterior Ø 6 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve, Discharge throttle (»C«) quick connector Hose 6/4, M5, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Stopper POM, Supports 10 mm, Colour red, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Miniature worm gear motor SFS Gr. 2 with DC-motor 24V i=62:1 idle speed 95 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047224

Locking assembly COM-A bore 45mm size 45-75 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577545

Product inlet/outlet size : #400 mm
SECC-4040-09S-N-Ex-F1E-L-B-B
SKU: SECC400201
Stock *: 0
Max. capacity: 90 m³/h
No of bars: 9 (4+5)
Weight: 174 kg
This unique Cleanflow type discharges the filtered ferrous contaminants during production. So no production stop is required. The time-interval controlled discharge of ferrous particles makes it suitable for product streams with relatively much ferrous contamination.Suitable for granulates and dry, free-flowing powders in free-fall transport pipes.The automatically controlled discharging of captured ferrous particles makes this type of Cleanflows suitable for places where they are hardly or not accessible for operation.

Automatic cleaning (continuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø34 mm, 9400 gauss)
Capacity 30 - 90 m³/h
ATEX II 1/2 D

Application

Powders & granulates with relatively much ferrous impurities

Suitable for granulates and free-flowing powders with relatively large amounts of ferrous contaminations in non-pressurized free-fall pipes.
 
Due to the automated contral and operation they are suitable for less easily accessible situations and / or centrally managed controls.
 
Not suitable for:

When product loss is unacceptable. During a cleaning cycle some product might flow out of the product channel, together with the caught magnetic particles.
Poorly flowing sticky / fatty powders that cause clogging. For those applications the rotating versions of these Cleanflows are a better solution.


Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
These automatic Cleanflow magnetic separators have 2 magnetic grids, placed staggered one above the other. They contain pneumatic magnetic bars, constructed of robust Ø34 mm SS tubes inside of which strong neodymium N42 magnet packages are moved by air pressure. The bars measure no less than 9400 gauss on the Ø34 mm tubes.
 
Summary of important specifications

Siemens LOGO! PLC control
Ø34 mm pneumatic operated magnetic bars
Magnet quality: neodymium N-42, 9400 gauss on the Ø34 mm tube
Material housing and magnetic bars: AISI304 / AISI316(L)
Finish: grit blasted
Material gaskets: PA6G acc. EC1935 / FDA


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Options

Version suitable for high temperatures up-to 120°C (not available for ATEX II 1/2D versions)
Magnetic bars end position detection (not available for ATEX II 1/2D versions)


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?

Production can continue during cleaning, because the magnetic bars of these Cleanflows are horizontally fixed inside the product channel. As a result, magnetic contaminants can never pass.
The pneumatic tubes enclosing the magnetic bars are horizontally fixed positioned in both the product channel and - in turn - in the left and right side chutes for iron particle discharging.
After you have given the start signal for an iron particle discharge cycle, the tubes slide over the magnets by air pressure to the left or right iron discharging chute. 
The retainer rings on the tubes hereby drag the trapped ferrous particles out of the product channel. Once outside the product channel, the ferrous particles fall off the tubes as soon as they are outside the influence of the magnets.
The time interval between 2 iron particles discharge cycles can be set locally, on the PLC control on the machine, or from your central control.

Protective cap for clamping bolt M12
Material: Hexagon Bolt: DIN 933, steel, strength class 8, zinc-plated. Hexagon nuts: DIN 934/DIN 936, steel, zinc-plated. Protective cap: Neoprene 85° Shore hardness, black. Note: protective cap has to be ordered separately. This protective cap is elastic and can be easily slipped over the bolt head.

Article ID: 67600052

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 100mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150100

2/2 solenoid valve DN 10 port G1/2 24V DC
Material: Housing: Brass, PA66 Seat seal: NBR (Perbunan) Internal parts: 1.4104, 1.4303, PVDF - For neutral gaseous and liquid fluids. - Electromagnetically actuated valve, with forced valve lifting. - Diaphragm valves. - Connection internal thread G1/4 to G1/2. - Operating pressure 0 to 10 bar (up to 25 mm²/s cSt). For contaminated fluids insertion of a strainer is recommended. Description (standard unit) Solenoid valve for, e.g., air , water, oil. Switching function: Normally closed. Flow direction: determined. Fluid temperature: -10°C to max. +90°C. Ambient temperature: -10 °C to max. +50°C. Mounting position: optional, preferably solenoid vertical on top. Features - Suitable for vacuum. - Clear design. - Compact solenoid with integrated core tube. - Valve works without minimum pressure difference (Zero Delta P). - Operating pressure 0 - 20 bar with alternating voltage and NBR seal.

Article ID: 85111211

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.1 - 2 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Elbow 2, 90°, long, Rp 2 IT, Rp 2 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Polycarbonate container incl. protective cage, with fully-automatic condensate drain (NC), for »FUTURA«, Size 2, G 3/8 and G 1/2

Filter »variobloc«, PC container, Size 1, G 3/8, Input pressure max. 16 bar, Med. / ambient temp. max. 50 °C, Manual bleeder valve
Centrifugal separators with a sintered filter element.
Filtration takes place in a 2-stage process comprising cyclone separation (condensate) and a PE filter element (particles).
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Straight screw-in fitting, M20x1,5 o., Pipe exterior Ø 14 mm, PN max. 630 bar, A/F1 27, A/F2 27, galvanised steel
Male connector, metric thread, heavy type

Push-in T-connector, Plug nipple 6 mm »Blue Series«, unequal, for hose exterior Ø 4 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Mounting sets (rails) for »SBP« basic ejectors, for all sizes
Mounting kit

Straight push-in fitting »Blue Series«, round, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Miniature worm gear motor SFS Gr. 2 with DC-motor 24V i=62:1 idle speed 140 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047324

Locking assembly COM-A bore 50mm size 50-80 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577550

Interface/connection dim's : DN50 acc. EN 1092-1 PN16
SFN-050-IF-04E-HT-F1m-S-B-B
SKU: SSFN005038
Stock *: 0
No of bars: 4
Build-in length: 230 mm
Weight: 13 kg
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

ECVCONB General features
Manages up to 500 devices
3 digital INPUTS and 2 output relais
Electric features
Power source module 24Vdc 15W, code: ODAL1

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 125mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150125

2/2 solenoid valve DN 10 port G1/2 230V 50/60Hz
Material: Housing: Brass, PA66 Seat seal: NBR (Perbunan) Internal parts: 1.4104, 1.4303, PVDF - For neutral gaseous and liquid fluids. - Electromagnetically actuated valve, with forced valve lifting. - Diaphragm valves. - Connection internal thread G1/4 to G1/2. - Operating pressure 0 to 10 bar (up to 25 mm²/s cSt). For contaminated fluids insertion of a strainer is recommended. Description (standard unit) Solenoid valve for, e.g., air , water, oil. Switching function: Normally closed. Flow direction: determined. Fluid temperature: -10°C to max. +90°C. Ambient temperature: -10 °C to max. +50°C. Mounting position: optional, preferably solenoid vertical on top. Features - Suitable for vacuum. - Clear design. - Compact solenoid with integrated core tube. - Valve works without minimum pressure difference (Zero Delta P). - Operating pressure 0 - 20 bar with alternating voltage and NBR seal.

Article ID: 85111212

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.2 - 4 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Straight push-in fitting, Exterior hexagonal, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 20 bar, Stainless steel
For use in more aggressive environments and corrosive media.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 10x8 mm, PN at 23 °C max. 7 bar, red, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

PVC braided hose set, Quick-connect coupling, Operating temp. max. 60 °C, Hose Ø 15x9, PN at 23 °C max. 15 bar, Length 10 m
Flexible, pressure-resistant and non-abrasive standard hose, also resistant to ageing. Assembled with brass stem and brass quick disconnect coupling DN 7.2.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Straight screw-in fitting, M18x1,5 o., Pipe exterior Ø 10 mm, PN max. 315 bar, A/F1 19, A/F2 24, galvanised steel, soft seal
Male connector, metric thread and soft seal, light type

Bushing, exterior hexagonal, red. G 1/4 i., G 3/8 i.nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Throttle check valve, Discharge throttle (»C«) threaded connection G 1/8 i., G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Straight reducing supports, for hose I.D. 6/4 mm, brass
Tube connectors for polyamide hoses and polyurethane hoses made of brass CW617N and acetal copolymer (POM).

Cranked chain link type 12 / L for roller chain 06 B-1 pitch 3/8x7/32
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel. With cranked links the power and breaking loads of the chain are reduced by 20%.
Article ID: 10100400

Miniature worm gear motor SFS Gr. 2 with DC-motor 24V i=59:3 idle speed 210 /min
Housing: Motor: Steel, zinc-plated. Gearbox: Aluminium.
Can be mounted in any position.
Teeth: Worm gear set made from plastic.
Bearing: Output side, plain bearing, motor side, ball bearing.
Lubrication: Maintenance free grease lubrication.
Motor: DC motor 12 V or 24 V, interference-free.
Change the direction of rotation by switching the polarity.
Protection class acc. to EN 60529: IP 30.
Operating mode as per VDE 0530: S2-10 min.
Permissible ambient operating temperature: -10 to +60°C.
Caution: Output shaft and shaft form side as per the table.
Ordering Details: e.g.: Type, idle speed, Product No.




Article ID: 43047424

Locking assembly COM-B bore 6mm size 6-14 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577606

Interface/connection dim's : DN65 acc. EN 1092-1 PN16
SFN-065-IF-04E-HT-F1m-S-B-B
SKU: SSFN006538
Stock *: 0
No of bars: 4
Build-in length: 228 mm
Weight: 13 kg
Robust filter for general industrial applications without risk of bacterial growth.For magnetic filtering of fine ferrous contaminants - such as stainless steel wear particles - from your liquid and powder flows in pressure pipes up to 10 bar.Manual quick-cleaning. The largest versions are additionally equipped with a removal guide, so that the magnet unit does not have to be lifted out, but can be extended.

Manual quick cleaning
Capture Fe particles from 30 µm - 2 mm
Sizes DN50-200
Max. 10 bar / 140 °C
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)

Application

Liquids and powders in pressure lines

This robust magnetic filter is suitable for industrial applications where liquid mixtures and powders are transported in pressure pipes up to 10 bar.
 
The design and finish are industrial, meaning they are only intended for use in applications with no risk of bacterial growth.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
The industrial magnetic filter is a very robustly built filter, with EN 1092-1 PN16 flat flanges.
 
Equipped with extractor bars Ø25/Ø23 mm for manual 'quick cleaning'. See explanation in tab 'Working principle'.
 
Summary of important specifications

Magnetic bars Ø23/Ø25 mm
Magnet quality N-42SH, 8,000 gauss on tube Ø25 mm
Max. 10 bar / 140 °C
Inlet/outlet: DN50 - D200 (EN1092-1)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available versions, options & accessories

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Types

DN50 to DN-125: can be cleaned by manually taking the magnet unit out.
DN100-150-200: can be cleaned by sliding the entire magnet unit out over the guide and then pulling it apart.
These types are easier and faster to clean. But also more durable, because the magnet unit remains on the separator, and therefore less likely gets damaged.


Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
The magnetic unit with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous impurities passes several magnetic bars while flowing through the filter.
 
The magnets attract passing ferromagnetic contaminants. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.
 
For larger passages, the cleaning is done by manually sliding the magnet unit out over guides, because these magnet units are too heavy to lift.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet unit
Lift / slide the complete magnet unit out of the housing
Take / slide the magnet unit out of the extractor unit
Small types: and place it away from the extractor unit on a clean surface. 
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Place / shove the complete magnet unit assembly back into the housing
Re-tighten the screw connections
Restart the product flow

ZL31A General features
Controlled fluid: cold and hot water with max 50% glycol volume.
Controlled fluid temperature 5 ÷ 120 ° C.
High closing point (▲).
Stainless steel shutter.
Stem in stainless steel.
EPDM O-ring stem seal.
Flow rate characteristic: – regulation port A – AB: equal percentage (VDI / VDE 2173) n (gl) = 3, bypass B – AB: linear (VDI / VDE 2173);
Leakage rate: adjustment port A – AB: max 0.05% Kvs, bypass B – AB: max. 1% of the value of kvs.
PN 16 flanges (according to ISO 7005-2);
GG25 valve.
Nominal pressure 1600 kPa.
Differential pressure ∆pmax 400 kPa.
Electric features
Power supply: 230V 50/60Hz.
Power consumption:– from DN25 to DN50 – 6VA;– from DN65 to DN150 – 10VA.
Power supply cable 1m – 4×0,75 mm².
Tolerance range AC 198…264 V.

Double-acting standard cylinder ISO 15552 cylinder diameter 50mm stroke 160mm pressure max. 12 bar
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (ferritic), Piston and piston rod seals: Polyurethane. O-ring seals: NBR. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 15552. Mode of operation: Double-acting with magnetic piston and adaptive end-of-stroke cushioning system ACS. Operating pressure:1 to 12 bar. Operating temperature: -20°C to +80°C max. Below +2°C please consider the air quality.
Article ID: 80150160

Service unit 2-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.5-10 bar, Semi
Two-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Distributor »multifix-mini«, Size 0, G 1/4, with 2 outlets G 1/8, Input pressure max. 16 bar, Medium / ambient temp. max. 60 °C
Narrow, two-way manifold with two G 1/8 outlets.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 10x8 mm, PN at 23 °C max. 7 bar, yellow, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Adjustable L-fitting, with cone seal, 360° swivel range, female nut M14x1.5 i., Pipe ext. Ø 6, PN max. 630 bar, galvanised steel

Straight screw-in fitting, M16x1,5 o., Pipe exterior Ø 12 mm, PN max. 315 bar, A/F1 22, A/F2 22, galvanised steel, soft seal
Male connector, metric thread and soft seal, light type

Screw-in hose connector, G 1/2 o., for hose I.D. 13 mm, AF 24, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Throttle check valve, Discharge throttle (»C«) quick connector Hose 8/6, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Plastic silencer with polyethylene damper element, G 1/4, Operating pressure 0 to 6 bar, Operating temperature max. 80 °C