Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ32, Stroke15, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled piece 45°, interior / interior, Rp 3/4, Operating pressure max. 20 bar, Operating temp. max. 175 °C, Stainless steel

Push-in L-fitting »Blue Series« mini, rotating, M6x1, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 6 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight screw-in fitting »value line«, G 1/4 o., for hose exterior Ø 4 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Feather key DIN 6885 version A 3 x 3 x 12 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899032

Adjusting ring DIN 705 A set screw with hexagon socket bore 85mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 623085006

Locking assembly COM-A bore 22mm size 22-47 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577522

Product inlet/outlet size : #300 mm
SECA-3030-03V-ES-F1H-B-P-ST-B-
SKU: E0104918
Stock *: 0
Max. capacity: 65 m³/h
No of bars: 3
Weight: 100 kg
These new 'EasyClean' type Cleanflows are equipped with robust Ø50mm magnetic bars, that measure no less than 12,000 gauss at the contact surface of the bars.Suitable for magnetic filtering of small amounts of ferrous and even weakly-magnetic contaminants from high-capacity granulate and powder flows in free-fall and low-pressure transport pipes up to 0.5 bar.The automatic cleaning makes this separator suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.

Automatic cleaning (discontinuous)
Magnetic bars in pneumatic tube (Ø50 mm, 12,000 gauss)
Capacity 30 - 110 m³/h
Pressure-tight up to 0.5 bar
Atex II 1/3 D

Application

Powders & granulates in free-fall and low-pressure pipes

This automatic cleaning Cleanflow magnet is very suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning. Via the connection box, it is possible to connect and control the magnet via the central control room. A local control box with PLC is optional.
 
The thick magnetic bars of Ø50 mm have a very high separation efficiency, due to a deep catch field and a high flux density. This ensures that not only ferromagnetic, but even weakly magnetic stainless steel contaminants are captured.
 
Due to the large distance between the magnetic bars, these Easy Cleanflows have a significantly higher capacity than the Cleanflows with thinner bars. This is also an advantage for slightly less flowing powders
 
Suitable for granulates and reasonably to well flowing powders in free-fall and low-pressure transport pipes up to 0.5 bar.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
These automated cleaning Cleanflow magnets contain 1 row with robust Ø50 mm magnetic bars with super strong magnet quality N52. This ensures that they optimally capture magnetic particles.
 
In case of extremely small or weakly magnetic particles, we mount a deflector grid at the separator inlet to make sure that particles cannot fall through freely, but will touch or very closely pass a magnetic bar.
 
The magnetic bars are sealed stainless steel tubes inside of which the magnets are blown in and out by air pressure.
 
Summary of important specifications

1 Magnetic grid with Ø50 mm robust, pneumatic operated magnetic bars
Optional deflector flange for guiding the product towards the magnetic bars
Magnet quality neodymium N-52, 12,000 gauss on the tube.
Housing pressure-tight up to 0.5 bar
Material housing: AISI316(L)
Finish: grit blasted
Material gaskets: Silicone EC1935 / FDA


Options

Available options

Default available options

Inlet/outlet adapter pieces from square to round
High temperatures versions - to 140°C - not available in combination with ATEX
Removable collecting bin - for collecting discharged ferrous particles
Deflector flange - for guiding the product flow towards the magnet bars
Surface finish polishing or wet blasting - for hygienic applications
Flange gaskets Silicone VMQ or NBR, neutral colour, all EC1935/2004 certified
Alternative for red silicone VMQ housing/magnet bar gasket ring: white Silicone, blue NBR70 or black Viton FKM70 (all versions are EC1935/2004 certified)
Thin-walled tubes - 0.7 mm instead of 1.2 mm - over the magnetic bars, for enabling catching of weakly-magnetic particles like stainless steel

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grid with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous contaminants passes the magnetic bars while flowing through the grid.
 
If necessary, an optional deflector flange will deflect the product flow towards the magnetic bars.
 
The magnets attract passing ferromagnetic contaminants; the captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, the magnet unit is automatically driven out of the product channel over the guides.
 
As soon as you pull out the magnet unit to its end of reach, air pressure automatically pushes the magnets out one stage further outside within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence:

Stop the product stream
Give start signal to the magnet's control unit

Now first the entire magnet unit is pneumatically driven out of the product channel over a robust guide
Then the magnets are pneumatically moved to their OUT position within their enveloping tubes
The captured metal particles fall from the tubes as soon as they are outside the range of the magnetic field
The magnets then automatically return to their IN position and at the same time the magnet unit is driven back inside the product channel
As soon as magnets and magnet unit are back IN the control gives a 'ready for production' signal
The production can now safely be resumed

EV70D Telecontrol General features
Instrument customisable via PC for all parameters.
Extractable terminal block for fast replacement of the instrument.
2-line display for setting parameters, remote monitoring and management for both GSM modem ( mobile telephony) and PSTN modem ( fixed telephony)
Mounted on DIN rail ( 9 modules)
Electric features
Absorption 10VA
8 digital inputs ON- OFF
4 analog inputs, via detection probes
4 output relays
Contact rating 5A- 230Vac ( ohmic charge).

Precision spur gear made of steel 16MnCr5 module 3 30 teeth bore 35mm hardened and ground outside diameter 96mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24383035

Ball valve heavy duty design, Manual lever, IT/IT, nickel-plated brass, Operating temp. -20 °C to 130 °C, G 2, PN max. 63 bar
Applications: Compressed air, water, neutral and non-toxic gases, fuel oil (light distillate), fuel oil (heavy), lubricating oils, diesel oils.

Tempered coupling DN 9, Exterior thread, Brass 2.0401, G 3/8 straight, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

2/2-way solenoid valve brass, NC, pilot operated, 24V DC, 8W, Medium temp. -10°C to 140°C, FKM, G 1/2, PN 0.2 - 16bar
Economy series available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

RIEGLER Lock AN 301-72, Anaerobic glue, Medium tight, High viscosity, Pipe / flat seal, DVGW, Temp. -60 °C to 200 °C, 50 ml
Non-classified adhesive for sensitive production areas

- Very good strength
- Resistant to high temperatures
- Good chemical resistance after curing
- High level of safety and health at work
- No irritation to eyes, nose or throat
- No marking with hazard symbols in accordance with EC Regulation No. 1907/2006 - ISO 11014-1

Pipe double nipple, G 1/2, Length 60 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Push-in L-fitting »Blue Series« mini, rotating, M6x1, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 0.6 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking screw, Hexagonal socket, without flange, G 3/8, AF 8, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Feather key DIN 6885 version A 10 x 8 x 35 mm material C45
Material: C45K.Version A.
Article ID: 61817400

Adjusting ring DIN 705 A set screw with hexagon socket bore 90mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 623090006

Polyurethane timing belt T20 width 75mm 75 T20 open length with tensile members from steel packed 3 x 25mm
Material: Thermoplastic polyurethane (TPU), white, with steel
tensile member.

Good resistance against oil, fats and many chemicals. Temperature range
-30º to +80ºC. T timing belts only run on T pulleys. Belts made of TPU
can be welded to endless belts. When welded, the perm. tensile force is
reduced to 50%.

Article ID: 16570000

Locking assembly COM-A bore 24mm size 24-50 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577524

Product inlet/outlet size : #400 mm
SECA-4040-04V-ES-F1H-B-P-ST-B
SKU: E0106728
Stock *: 0
Max. capacity: 110 m³/h
No of bars: 4
Weight: 130 kg
These new 'EasyClean' type Cleanflows are equipped with robust Ø50mm magnetic bars, that measure no less than 12,000 gauss at the contact surface of the bars.Suitable for magnetic filtering of small amounts of ferrous and even weakly-magnetic contaminants from high-capacity granulate and powder flows in free-fall and low-pressure transport pipes up to 0.5 bar.The automatic cleaning makes this separator suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.

Automatic cleaning (discontinuous)
Magnetic bars in pneumatic tube (Ø50 mm, 12,000 gauss)
Capacity 30 - 110 m³/h
Pressure-tight up to 0.5 bar
Atex II 1/3 D

Application

Powders & granulates in free-fall and low-pressure pipes

This automatic cleaning Cleanflow magnet is very suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning. Via the connection box, it is possible to connect and control the magnet via the central control room. A local control box with PLC is optional.
 
The thick magnetic bars of Ø50 mm have a very high separation efficiency, due to a deep catch field and a high flux density. This ensures that not only ferromagnetic, but even weakly magnetic stainless steel contaminants are captured.
 
Due to the large distance between the magnetic bars, these Easy Cleanflows have a significantly higher capacity than the Cleanflows with thinner bars. This is also an advantage for slightly less flowing powders
 
Suitable for granulates and reasonably to well flowing powders in free-fall and low-pressure transport pipes up to 0.5 bar.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
These automated cleaning Cleanflow magnets contain 1 row with robust Ø50 mm magnetic bars with super strong magnet quality N52. This ensures that they optimally capture magnetic particles.
 
In case of extremely small or weakly magnetic particles, we mount a deflector grid at the separator inlet to make sure that particles cannot fall through freely, but will touch or very closely pass a magnetic bar.
 
The magnetic bars are sealed stainless steel tubes inside of which the magnets are blown in and out by air pressure.
 
Summary of important specifications

1 Magnetic grid with Ø50 mm robust, pneumatic operated magnetic bars
Optional deflector flange for guiding the product towards the magnetic bars
Magnet quality neodymium N-52, 12,000 gauss on the tube.
Housing pressure-tight up to 0.5 bar
Material housing: AISI316(L)
Finish: grit blasted
Material gaskets: Silicone EC1935 / FDA


Options

Available options

Default available options

Inlet/outlet adapter pieces from square to round
High temperatures versions - to 140°C - not available in combination with ATEX
Removable collecting bin - for collecting discharged ferrous particles
Deflector flange - for guiding the product flow towards the magnet bars
Surface finish polishing or wet blasting - for hygienic applications
Flange gaskets Silicone VMQ or NBR, neutral colour, all EC1935/2004 certified
Alternative for red silicone VMQ housing/magnet bar gasket ring: white Silicone, blue NBR70 or black Viton FKM70 (all versions are EC1935/2004 certified)
Thin-walled tubes - 0.7 mm instead of 1.2 mm - over the magnetic bars, for enabling catching of weakly-magnetic particles like stainless steel

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grid with very strong neodymium magnetic bars is positioned in the middle of the product flow. The product with ferrous contaminants passes the magnetic bars while flowing through the grid.
 
If necessary, an optional deflector flange will deflect the product flow towards the magnetic bars.
 
The magnets attract passing ferromagnetic contaminants; the captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, the magnet unit is automatically driven out of the product channel over the guides.
 
As soon as you pull out the magnet unit to its end of reach, air pressure automatically pushes the magnets out one stage further outside within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence:

Stop the product stream
Give start signal to the magnet's control unit

Now first the entire magnet unit is pneumatically driven out of the product channel over a robust guide
Then the magnets are pneumatically moved to their OUT position within their enveloping tubes
The captured metal particles fall from the tubes as soon as they are outside the range of the magnetic field
The magnets then automatically return to their IN position and at the same time the magnet unit is driven back inside the product channel
As soon as magnets and magnet unit are back IN the control gives a 'ready for production' signal
The production can now safely be resumed

K20A, K30A, K40A General features
Cable composition:– 1.25 mm² conductors– Self-adjusting conductive core– Polyolefin insulating sheath– Braided copper sheath– Outer sheath in modified polyolefin
Minimum installation room temperature -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Cable dimensions– 12.6 x 4.8 mm series K20A– 14.6 x 4.8 mm series K30A-K40A
Electric features
Power supply 230V-50Hz
Tolerance -0/+5 W
Power delivered– K20A 20 W/m at 10°C– K30A 30 W/m at 10°C– K40A 40 W/m at 10°C

Spur gear made of POM with hub module 2.5 60 teeth tooth width 20mm outside diameter 155mm
Material: POM, white / nature, milled teeth. Tooth quality 10d25 DIN 3967. Pressure angle 20°. Untoleranced dimensions in accordance with DIN ISO 2768 middle. Temperature limit: continuous 100°C, only short time 160°C. Water absorption (satiable) 0,5% Cws.
Article ID: 29706000

Ball valve heavy duty design, Manual lever, IT/ET, nickel-plated brass, Operating temp. -20 °C to 130 °C, G/R 2, PN max. 63 bar
Applications: Compressed air, water, neutral and non-toxic gases, fuel oil (light distillate), fuel oil (heavy), lubricating oils, diesel oils.

Tempered coupling DN 9, Exterior thread, Blocking valve, Brass, G 3/8 straight, Operating pressure max. 15 bar
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

2/2-way solenoid valve brass, NC, pilot operated, 230-240V, 50-60Hz, 16VA, Medium temp. -10°C to 140°C, FKM, G 1/2, PN 0.2 - 16bar
Economy series available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Kamlok quick-connect plug, Hose sleeve, E type, Stainless steel 1.4401, for hose I.D. 50, Plug Ø 63 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Bracket 92, 90°, Rp 1 1/2 IT, R 1 1/2 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in connector »Blue Series« mini, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Push-in T-fitting »Blue Series«, rotating, R 1/2 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Thread plug nipple »click-clock«, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
By combining these parts with unions, union elbows and union tees, you can obtain all essential connecting variants and simultaneously reduce your warehousing costs.

Adjusting ring DIN 705 A set screw with hexagon socket bore 100mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 623100006

Splined hub with flange DIN 14 KN 36X42 length 80mm red brass Rg7
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64856200

Locking assembly COM-A bore 25mm size 25-50 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577525

Product inlet/outlet size : #320 mm
SECD-3232-11P-N-F1H-V-P-B-E
SKU: SECD320016
Stock: 0
Max. capacity: 60 m³/h
No of bars: 11 (5+6)
Build-in length: 824 mm
For magnetic filtering of small amounts of ferrous contaminants from dusty, free-flowing powders in free-fall transport pipes.The automatic cleaning makes this type suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.Industrial finish - grit blasting Ra 3 µm

Automatic cleaning (discontinuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø25 mm, 11,000 gauss)
Dust-proof
ATEX II 1/2 D

Application

Dusty powders in free-fall pipes

These automatic, discontinuously cleaning, dust-proof Cleanflows are especially suitable for dusty powders with a small amount of ferrous impurities.
 
Also suitable for non-dusty powders & granulates, but NOT for sticky powders that cause blockages. For those applications the rotating versions of this type Cleanflows are a better solution.
 
The automatic cleaning makes them suitable for badly accessible situations.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids with Ø25 magnetic bars, placed staggered one above the other
Pneumatic bar and valve movement
Magnet quality: neodymium N-42, 11,000 gauss on the tube
Dust-proof housing
Material housing: AISI304 / AISI316(L)
Finish: grit blasting
Material gaskets/seals: Silicone EC1935 / FDA


Options

Available accessories & options

Online available accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Available options

Integrated valve box for ferrous particles disposal
(our advice: always order with corresponding valve box for trouble-free operation)
Iron discharge cycle control:

Pneumatic control -> start by local push button
Siemens LOGO! PLC control -> start by local push button or from control room


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, air pressure automatically pushes the magnets out within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence

Stop the product stream
Give start signal to the magnet's control unit

Now first the valve in the valve box is automatically switched to iron discharge position
Then the magnets inside the pneumatic tubes are moved automatically out of the product channel
The captured metal particles want to 'travel' with the magnets, but are held by retainer rings on the magnet bar tubes. As soon as the magnets are out of reach, the captured particles automatically drop off of the tubes, into the valve box, where they are discharged further
Then the magnets inside the pneumatic tubes are moved automatically back into the product channel
When the magnets are all back in, the valve will automatically be switched back to its production position
As soon as the magnets and valve are back in production position, the control will give a 'ready for production' signal
You can now safely resume production

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Ball head precision levelling adjuster MN 686.4 40-26.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699450

Ball valve heavy duty design, Manual lever, ET/ET, nickel-plated brass, Operating temp. -20 °C to 130 °C, R 2, PN max. 80 bar
Applications: Compressed air, water, neutral and non-toxic gases, fuel oil (light distillate), fuel oil (heavy), lubricating oils, diesel oils.

T-multi-distributor »Blue Series«, 6-fold, rotating, R 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

2/2-way solenoid valve brass, NC, pilot operated, 230-240V, 50-60Hz, 16VA, Medium temp. -10°C to 140°C, FKM, G 3/8, PN 0.2 - 16bar
Economy series available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Fork head, »Y« type (incl. thread adapter), for compact cylinder »ACP«, Piston Ø 100, Piston rod thread M12x1.75 i.
Fork model, »Y« type (incl. threaded adapter)

Fitting elbow 95, flat sealing, IT/IT, Rp 1/2, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galvanised
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Push-in L-connector »Blue Series« mini, for hose exterior Ø 4 mm, Working pressure max. 10 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Push-in L-fitting »Blue Series«, Self-locking, R 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

T-reducer supports, for hose I.D. 8/4/8 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2.5 40 teeth tooth width 25mm outside diameter 105mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23295040

Locking assembly COM-A bore 28mm size 28-55 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Clamping bush for medium high torques; not self-centering.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Due to the large cone angle, the clamping set
releases on its own after the screws have been fully unfastened.

There are three larger threads cut into the front ring, which serve to
remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub
QPQ Surface Properties: Very
good corrosion resistance, betterthan hard chrome or chem. nickel.
Corrosion resistance in the salt spraytest SS CASS in accordance with
DIN 50021. Layer thickness of 10 - 25 µmpossible. For medium operational
demands we recommend a layer thicknessof 15 µm at a 90 minute treatment.
Only very small changes in dimensions(only 5 µm), as the surface
modification is achieved through diffusionand not application. Surface
hardness same as clamping set material =350 HV. Improved wear
resistance, no fretting corrosion, no cold shut.Increased endurance
strength, sometimes up to 100% higher. Is completelysafe to use with
food as long as there is no contact with any acidicsubstances with a
pH-value of = 4.

Article ID: 61577528

Product inlet/outlet size : #400 mm
SECD-4040-14P-N-F1H-V-P-B-E
SKU: SECD400016
Stock: 0
Max. capacity: 90 m³/h
No of bars: 14 (7+7)
Build-in length: 924 mm
For magnetic filtering of small amounts of ferrous contaminants from dusty, free-flowing powders in free-fall transport pipes.The automatic cleaning makes this type suitable for situations where the magnetic separator is hardly or not accessible for operation and cleaning.Industrial finish - grit blasting Ra 3 µm

Automatic cleaning (discontinuous)
2 magnetic grids, placed in cascade
Magnetic bars in pneumatic tube (Ø25 mm, 11,000 gauss)
Dust-proof
ATEX II 1/2 D

Application

Dusty powders in free-fall pipes

These automatic, discontinuously cleaning, dust-proof Cleanflows are especially suitable for dusty powders with a small amount of ferrous impurities.
 
Also suitable for non-dusty powders & granulates, but NOT for sticky powders that cause blockages. For those applications the rotating versions of this type Cleanflows are a better solution.
 
The automatic cleaning makes them suitable for badly accessible situations.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids with Ø25 magnetic bars, placed staggered one above the other
Pneumatic bar and valve movement
Magnet quality: neodymium N-42, 11,000 gauss on the tube
Dust-proof housing
Material housing: AISI304 / AISI316(L)
Finish: grit blasting
Material gaskets/seals: Silicone EC1935 / FDA


Options

Available accessories & options

Online available accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Available options

Integrated valve box for ferrous particles disposal
(our advice: always order with corresponding valve box for trouble-free operation)
Iron discharge cycle control:

Pneumatic control -> start by local push button
Siemens LOGO! PLC control -> start by local push button or from control room


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
Each magnetic bar has a magnet package that pneumatically moves inside a closed tube, this way automatically discharging trapped ferrous particles.
 
After you have stopped the product flow and have given the start signal for cleaning to the control, air pressure automatically pushes the magnets out within their enclosing tubes.
 
The moving magnets in the tubes pull the captured ferrous particles along outside. However, they are stopped by a plate halfway the tube length. As soon as the magnets have traveled completely out, the captured particles drop off the tubes, into the iron discharge chute, where you collect and further discharge them.
 
Cleaning / iron discharging sequence

Stop the product stream
Give start signal to the magnet's control unit

Now first the valve in the valve box is automatically switched to iron discharge position
Then the magnets inside the pneumatic tubes are moved automatically out of the product channel
The captured metal particles want to 'travel' with the magnets, but are held by retainer rings on the magnet bar tubes. As soon as the magnets are out of reach, the captured particles automatically drop off of the tubes, into the valve box, where they are discharged further
Then the magnets inside the pneumatic tubes are moved automatically back into the product channel
When the magnets are all back in, the valve will automatically be switched back to its production position
As soon as the magnets and valve are back in production position, the control will give a 'ready for production' signal
You can now safely resume production

EV70A Telecontrol General features
Instrument customisable via PC for all parameters.
Extractable terminal block for fast replacement of the instrument.
Lateral serial port for connection to the modem, separate from the front port to allow easy connection to the programming PC.

Precision spur gear made of steel 16MnCr5 module 2 48 teeth bore 25mm hardened and ground outside diameter 100mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2.
Teeth, bores and faces ground.

Tooth quality 7 e25.
Pressure angle 20°.

Feather Keyways in accordance with DIN 6885/1, tolerance P9.
Position of keyway to tooth is not defined.

Article ID: 24184825

Precision worm wheel centre distance 50mm i=19 19 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33001900

Wear part set, for stainless steel filter regulator, 1.4404, with secondary venting (reversible), G 1/4

T-multi-distributor »Blue Series«, 6-fold, rotating, G 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Mist oiler »Standard«, Metal container and metal drip cap, Size 1, G 1/4, Input pressure max. 25 bar, Med./ambient temp. max. 60°C
Proportional lubricators, oil can be filled under pressure.