Plug with sealing ring thread G3/8A
Material: Brass, nickel-plated. Sealing ring from aluminium.
Article ID: 86590038

Precision spur gear made of steel 16MnCr5 module 2 48 teeth bore 20mm hardened and ground outside diameter 100mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2.
Teeth, bores and faces ground.

Tooth quality 7 e25.
Pressure angle 20°.

Feather Keyways in accordance with DIN 6885/1, tolerance P9.
Position of keyway to tooth is not defined.

Article ID: 24184820

Precision worm wheel centre distance 50mm i=46 46 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33004600

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ125, Stroke40,G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled piece, 45°, interior / exterior, G 1, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Round cylinder, ISO 6432, double-acting, Magnet, Piston Ø 25, Stroke 50, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ25,Stroke5,M5, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, G 3/4 o., Pipe exterior Ø 20 mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Nipple for couplings I.D. 7.2 - 7.8, hardened / galv. steel, R 1/4 ET, PTFE, Operating pressure max. 16 bar, Temp. -20°C to 100°C

Replacement parts set for dirt strainers made of red brass, Screen and seal, Mesh width 0.6 mm, for connection size 1

Extension piece, Long, G 1/8 o., G 1/8 i., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Spur gear made of stainless steel 1.4305 with hub module 2.5 48 teeth tooth width 20mm outside diameter 125mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23299048

Locking assembly COM-B bore 24mm size 24-34 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577624

Interface/connection dim's : DN100 acc. EN 1092-1 PN16
SFN-100-IF-02O-N-F1m-S-B-B
SKU: SZFN001560
Stock *: 0
Capacity: 25 m³/h (at 1m/s)
Build-in length: 360 mm
Weight: 74 kg
Very robust filter, suitable for filtering large ferrous contaminants of 1-50 mm out of coarse or high-capacity product flows under pressure, such as pulp in the paper industry. The magnets are placed on the outside of the product channel. Therefore the passage is completely free, enabling large parts to pass unobstructed.

Manual cleaning (wipe off)
Capture Fe particles from 1 - 50 mm
Flanges DN100-250 (EN 1092-1)
Max. 10 bar / 60 °C
Plate magnets on side (6,000 gauss)

Application

High-capacity & coarse product flows

This very robust magnetic filter is designed especially for larger capacities and coarser product flows.
 
An example of a common application is pulp in the paper industry.
 
Because the magnets are located outside the product stream, this filter permits better flow than filters with magnetic bars.
 
However, the magnetic contact is less, so that only larger ferrous particles will be filtered out.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
This industrial magnetic filter is equipped with plate magnets, placed on the sides of the product channel. This permits a better flow than filters with magnetic bars, because they are placed in the middle of the product flow.

2 Plate magnets outside product channel
Magnet quality N-35, 6,000 gauss on the magnet contact surface
Max. 10 bar / 60 °C
Inlet/outlet DN100 - 250 (EN 1092-1 PN16)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
2 strong neodymium plate magnets are positioned on the sides of the product channel. Here they attract passing ferromagnetic contaminants. The captured ferrous particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
After the product stream is stopped, you swing the magnets outwards. Now wipe them clean by hand.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet units
Swing the magnet units outwards as far as possible
Wipe clean the magnet with a soft cloth and - if necessary - a suitable cleaning fluid
Swing the magnet units back against the housing
Re-tighten the screw connections
Restart the product flow

Spur gear made of POM with hub module 2 120 teeth tooth width 16mm outside diameter 244mm
Material: POM, white / nature, milled teeth. Tooth quality 10d25 DIN 3967. Pressure angle 20°. Untoleranced dimensions in accordance with DIN ISO 2768 middle. Temperature limit: continuous 100°C, only short time 160°C. Water absorption (satiable) 0,5% Cws.
Article ID: 29612000

Precision worm wheel centre distance 50mm i=55 55 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33005500

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125, Stroke40, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Sintered bronze silencer, Slot, G 1, Operating pressure max. 10 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 8x6 mm, PN at 20 °C max. 9 bar, natural (milky), Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Compact cyl.ISO 21287, single-acting, female piston rod, ext.,magnet,PistonØ25,Stroke5,M5, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled screw-in fitting POM, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Straight push-in fitting »Blue Series«, G 1/4 i., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Elbow 1a, short, 90°, IT/ET, Rp/R 1 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvan., DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

2-ear hose clamp, Steel bright galvanised (W1), Clamping range 40.0 - 43.0 mm, Belt width 10.0 mm
Quick and safe assembly: the two parts are simply pressed together.

Spur gear made of stainless steel 1.4305 with hub module 2.5 50 teeth tooth width 20mm outside diameter 130mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23299050

Locking assembly COM-B bore 25mm size 25-34 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577625

Interface/connection dim's : DN125 acc. EN 1092-1 PN16
SFN-125-IF-02O-N-F1m-S-B-B
SKU: SZFN001460
Stock *: 0
Capacity: 45 m³/h (at 1m/s)
Build-in length: 358 mm
Weight: 76 kg
Very robust filter, suitable for filtering large ferrous contaminants of 1-50 mm out of coarse or high-capacity product flows under pressure, such as pulp in the paper industry. The magnets are placed on the outside of the product channel. Therefore the passage is completely free, enabling large parts to pass unobstructed.

Manual cleaning (wipe off)
Capture Fe particles from 1 - 50 mm
Flanges DN100-250 (EN 1092-1)
Max. 10 bar / 60 °C
Plate magnets on side (6,000 gauss)

Application

High-capacity & coarse product flows

This very robust magnetic filter is designed especially for larger capacities and coarser product flows.
 
An example of a common application is pulp in the paper industry.
 
Because the magnets are located outside the product stream, this filter permits better flow than filters with magnetic bars.
 
However, the magnetic contact is less, so that only larger ferrous particles will be filtered out.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
This industrial magnetic filter is equipped with plate magnets, placed on the sides of the product channel. This permits a better flow than filters with magnetic bars, because they are placed in the middle of the product flow.

2 Plate magnets outside product channel
Magnet quality N-35, 6,000 gauss on the magnet contact surface
Max. 10 bar / 60 °C
Inlet/outlet DN100 - 250 (EN 1092-1 PN16)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
2 strong neodymium plate magnets are positioned on the sides of the product channel. Here they attract passing ferromagnetic contaminants. The captured ferrous particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
After the product stream is stopped, you swing the magnets outwards. Now wipe them clean by hand.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet units
Swing the magnet units outwards as far as possible
Wipe clean the magnet with a soft cloth and - if necessary - a suitable cleaning fluid
Swing the magnet units back against the housing
Re-tighten the screw connections
Restart the product flow

Precision worm wheel centre distance 50mm i=69 69 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 33006900

Round cylinder »MI«, double-acting, Magnet, Piston Ø 40, Stroke 600, G 1/4, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Nipple for pushbutton safety couplings I.D. 11, ISO 6150 C, Stainless steel, G 1/2 IT, max. 16 bar, Temp. -20 °C to 200 °C

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 8x6 mm, PN at 20 °C max. 9 bar, blue, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Compact cyl.ISO 21287, single-acting, male piston rod ext.,magnet,PistonØ25,Stroke5,M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Locking screw, Hexagonal socket 19 mm, G 1, NBR O-ring, nickel-plated brass, Max. working pressure 25 bar, Max.operating temp.80°C
Suitable for air, water, oil, steam, etc.

L screw-in fitting, ET conical, R 1/8, for hose 6/4 mm, AF 9, Working pressure max. 18 bar, nickel-plated brass

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 2 1/2, Length 200 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Worm thread - hose clamp »blow line«, Stainless steel (W 5) 1.4401, Belt width 9.0 mm, Clamping range 40.0 - 60.0 mm

Spur gear made of stainless steel 1.4305 with hub module 1 120 teeth tooth width 10mm outside diameter 122mm
Material: Stainless steel 1.4305.

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.


Article ID: 21499120

Spur gear made of stainless steel 1.4305 with hub module 2.5 55 teeth tooth width 20mm outside diameter 142.5mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23299055

Locking assembly COM-B bore 28mm size 28-39 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577628

Interface/connection dim's : DN150 acc. EN 1092-1 PN16
SFN-150-IF-02O-N-F1m-S-B-B
SKU: E0119190
Stock *: 0
Capacity: 70 m³/h (at 1m/s)
Build-in length: 360 mm
Weight: 80 kg
Very robust filter, suitable for filtering large ferrous contaminants of 1-50 mm out of coarse or high-capacity product flows under pressure, such as pulp in the paper industry. The magnets are placed on the outside of the product channel. Therefore the passage is completely free, enabling large parts to pass unobstructed.

Manual cleaning (wipe off)
Capture Fe particles from 1 - 50 mm
Flanges DN100-250 (EN 1092-1)
Max. 10 bar / 60 °C
Plate magnets on side (6,000 gauss)

Application

High-capacity & coarse product flows

This very robust magnetic filter is designed especially for larger capacities and coarser product flows.
 
An example of a common application is pulp in the paper industry.
 
Because the magnets are located outside the product stream, this filter permits better flow than filters with magnetic bars.
 
However, the magnetic contact is less, so that only larger ferrous particles will be filtered out.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
This industrial magnetic filter is equipped with plate magnets, placed on the sides of the product channel. This permits a better flow than filters with magnetic bars, because they are placed in the middle of the product flow.

2 Plate magnets outside product channel
Magnet quality N-35, 6,000 gauss on the magnet contact surface
Max. 10 bar / 60 °C
Inlet/outlet DN100 - 250 (EN 1092-1 PN16)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
2 strong neodymium plate magnets are positioned on the sides of the product channel. Here they attract passing ferromagnetic contaminants. The captured ferrous particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
After the product stream is stopped, you swing the magnets outwards. Now wipe them clean by hand.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet units
Swing the magnet units outwards as far as possible
Wipe clean the magnet with a soft cloth and - if necessary - a suitable cleaning fluid
Swing the magnet units back against the housing
Re-tighten the screw connections
Restart the product flow

Slide set DZ 2907 slide length 406mm zinc plated
Material: Slide elements: Cold rolled steel, zinc-plated. Ball retainers: Plastic / zinc-plated steel. Balls: Hardened steel.Sold by pair (1 x product no. = 1 pair of slides).Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Locks in open position. Fast disconnection. Bracket mount for electrical cabinets on request. Optional clip-on brackets available. For infrequent use, service life up to 2,000 cycles. Temperature range: -20°C to +70°C. NoteRecommended fastening: M4 screw.Use all mounting positions to achieve the max. load ratings.

Article ID: 64902216

Flange pressure controller, Flange pressure 300 bar, for non-flammable gases, Gas type: Nitrogen, Working pressure 0 - 10 bar
Single-stage type of construction acc. to DIN EN ISO 2503, with shut-off valve and safety valve as well as pressure gauges for the cylinder contents and working pressure.

Mounting bracket incl. 2 screws, galvanised steel, for »FUTURA«, Size 4, G 3/4 and G 1

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 8x6 mm, PN at 20 °C max. 9 bar, black, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Elbow 40, 45°, IT/ET, Rp/R 2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in bulkhead connector reducing »click-clock«, M15x1, for hose exterior Ø 6/8 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Push-in L-fitting »Blue Series«, rotating, G 1/4 i./o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Adjustable male connector, with cone seal, M22x1.5 o., Pipe exterior Ø 16, PN 400, a/f1 27, a/f2 30, galvanised steel

Replacement seal made of NBR, for Kamlok couplings made of aluminium, for coupling DN 75 (3")

Spur gear made of stainless steel 1.4305 with hub module 2.5 60 teeth tooth width 20mm outside diameter 155mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.




Article ID: 23299060

Worm shaft made of steel 11SMnPb30 module 2 double-thread right hand
Material: Steel 11SMnPb30, milled, with centring holes.

Double-thread worms to be paired with double-thread worm gears.
If the module (and number of threads) are matching, various ratios
at various axle distances can be realized.

Pressure angle 20°.


Article ID: 30150100

Locking assembly COM-B bore 30mm size 30-41 QPQ-coated
Material: Steel, QPQ coated. High corrosion resistance,improved
fatigue strength, primarily food safe.

Self-centering clamping bush for small hub diametres. For medium
torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61577630

Interface/connection dim's : DN200 acc. EN 1092-1 PN10
SFN-200-IF-02O-N-F1m-S-B-B
SKU: SZFN000360
Stock *: 0
Capacity: 110 m³/h (at 1m/s)
Build-in length: 460 mm
Weight: 115 kg
Very robust filter, suitable for filtering large ferrous contaminants of 1-50 mm out of coarse or high-capacity product flows under pressure, such as pulp in the paper industry. The magnets are placed on the outside of the product channel. Therefore the passage is completely free, enabling large parts to pass unobstructed.

Manual cleaning (wipe off)
Capture Fe particles from 1 - 50 mm
Flanges DN100-250 (EN 1092-1)
Max. 10 bar / 60 °C
Plate magnets on side (6,000 gauss)

Application

High-capacity & coarse product flows

This very robust magnetic filter is designed especially for larger capacities and coarser product flows.
 
An example of a common application is pulp in the paper industry.
 
Because the magnets are located outside the product stream, this filter permits better flow than filters with magnetic bars.
 
However, the magnetic contact is less, so that only larger ferrous particles will be filtered out.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
This industrial magnetic filter is equipped with plate magnets, placed on the sides of the product channel. This permits a better flow than filters with magnetic bars, because they are placed in the middle of the product flow.

2 Plate magnets outside product channel
Magnet quality N-35, 6,000 gauss on the magnet contact surface
Max. 10 bar / 60 °C
Inlet/outlet DN100 - 250 (EN 1092-1 PN16)
Finish: grit blasted
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone acc. EC1935 / FDA


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous impurities

How does the magnetic filtering work?
2 strong neodymium plate magnets are positioned on the sides of the product channel. Here they attract passing ferromagnetic contaminants. The captured ferrous particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
After the product stream is stopped, you swing the magnets outwards. Now wipe them clean by hand.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the srew connections of the magnet units
Swing the magnet units outwards as far as possible
Wipe clean the magnet with a soft cloth and - if necessary - a suitable cleaning fluid
Swing the magnet units back against the housing
Re-tighten the screw connections
Restart the product flow

Shaft collar DIN 705 A with set screw with slot bore 5 mm stainless steel 1.4305
Material: 1.4305.Light-duty series. With set screw DIN EN 27 434 made from stainless steel.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC,
Article ID: 62399005

Rod end GT-R DIN 12240-4 series K internal thread M30x2 right maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299630

Flange pressure controller, Flange pressure 300 bar, for non-flammable gases, Gas type: Compressed air, Working pressure 0-10 bar
Single-stage type of construction acc. to DIN EN ISO 2503, with shut-off valve and safety valve as well as pressure gauges for the cylinder contents and working pressure.

Quick-connect coupling I.D. 7.8, Steel, R 1/2 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Single-sided blocking, high quality and robust quick connect coupling for high flow values.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive, mining.

Low noise flat nozzle, G 1/4 ET, Safety nozzle general applications, nickel-plated brass, Length 100.0 mm, Nozzle width 21 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Thread plug nipple, R 3/8 o. , Plug connenction Ø 10 mm, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Straight push-in bulkhead connector reducing »click-clock«, M17x1, for hose exterior Ø 8/10 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation