Bevel gear made of steel module 3 60 teeth i=4:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).With crowned, milled teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36149300

V-belt pulley material aluminium profile XPA, SPA and A (13) 2 grooves nominal diameter 224mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15222200

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 12.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ100,Stroke300,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Relief valve

T-piece, interior / exterior / interior, G/R 3/8, Operating pressure max. 150 bar, Operating temp. -20°C to 150°C, Stainless steel

Flange fastening, »FA« type for short stroke cylinder »ACQ« and »ASQ«, Piston Ø 32
Flange model, »FA« type

Push-in L-connector »Blue Series«, for hose exterior Ø 10 mm, Working pressure max. 10 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in connector »Blue Series«, Self-locking, for hose exterior Ø 12 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Straight push-in fitting »click-clock«, M5 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 12mm outer diameter 16mm length 12mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62332700

Size : Ø43 mm
DECOMAGNEET R43 PVC STAAL HAAK
SKU: GM14410
Stock: 0
Holding force: 120 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Worm shaft made of steel C45 module 4 single-thread right hand
Material: Steel C45, whirled, with centring holes. Single-thread worms to be paired with single-thread worm gears. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°.

Article ID: 31030100

V-belt pulley material aluminium profile XPZ, SPZ and Z (10) 3 grooves nominal diameter 200mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. * without cast-iron hub reinforcement.

Article ID: 15032000

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 17 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ100,Stroke300, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, R 3/8, Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel 1.4571

T-piece, Interior / interior / interior, G 3/8, Operating pressure max. 150 bar, Operating temp. -20 °C to 150 °C, Stainless steel

Flange fastening, »FA« type for compact cylinder »ACP«, Piston Ø 40
Flange model, »FA« type

Flange fastening, for round cylinder ISO 6432, Piston Ø 12-16, 1 piece
Flange model

Manual sliding valve, Operating temperature 0 °C to 70 °C, G 1/8 ET, AF 14, PN max. 10 bar
For use on devices that have to be vented whenever they are turned off, either because of safety regulations or for technical reasons. The pneumatic devices are disconnected from the system and simultaneously vented each time they are shut off.

Straight push-in fitting »click-clock«, M5 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Round trapezoidal nut red brass Rg7 Tr.50 x 8 single-start left length 100mm outer diameter 90mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64385000

Angle joint DIN 71802 type CS with safety circlip size 8 thread M5 right with nut steel zinc-plated
Material: Steel zinc-plated. With threaded bolt and hexagon nut,
ball stud hardened.
Form C: Without circlip.
Form CS: With circlip.
Thread: Gewindeausführung rechts = right handed thread in the
socket. Gewindeausführung links = left handed thread in the socketmarked
with a circumferential groove.

* Pivoting angle reduced by circlip.

Article ID: 63660500

Size : 34 x 29 mm
DECOMAGNEET RH 34X29 PVC WIT
SKU: GM14437
Stock: 4
Holding force: 80 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Worm shaft made of steel C45 module 4 double-thread right hand
Material: Steel C45, whirled, with centring holes. Double-thread worms to be paired with double-thread worm gears. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°.

Article ID: 31050100

Slide set DZ 5417 slide length 400mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in the closed position. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 049 30, Slides 5417
Article ID: 64904940

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 18.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

3-way ball valve, L-hole, Stainless steel 1.4408, G 1, DN 20, Operating temperature -20 °C to 180 °C, PN max. 63 bar
With L or T-bore, reduced bore.
Version for sealing on all sides with integrated ISO flange plate (ISO 5211).
The lever can be turned 360° to allow several switching variants.

Straight push-in fitting, Exterior hexagonal, R 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 20 bar, Stainless steel
For use in more aggressive environments and corrosive media.

Counter bearing, ISO 15552, for compact cylinder, Standard cylinder, Piston Ø 63, with 4 screws
Counter-hinge model

Foot fastening, »LB« type for standard cylinder »SE« and »SAI«, for piston Ø 63, consists of 2 foot brackets and 4 screws
Foot model, »LB« type

L-ring piece, for hollow screw G 3/8, for hose exterior Ø 10 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 70 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Push-in L-fitting »Blue Series«, Self-locking, R 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Straight push-in fitting »click-clock«, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Round trapezoidal nut red brass Rg7 Tr.52 x 8 single-start left length 104mm outer diameter 90mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64385200

Spherical washer DIN6319 inner Ø 6,4mm outerØ 12mm for bolt diameter6mm stainless steel 1.4401 / AISI316
Material: 1.4401.* total height, together with conical seat DIN 6319.
Article ID: 65599456

Size : 42 x 14 mm
DECOMAGNEET RH 42x14 PVC WIT
SKU: GM14438
Stock: 0
Holding force: 55 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Splined shaft similar to DIN 14 profile KW 16X20 x 2000mm long stainless steel 1.4301
Material: Stainless steel 1.4301, cold drawn. Lengths in stock: 1000, 1500, 2000 and 3000 mm. Special lengths up to 6000 mm on request (some in stock). Tolerances: Straightness 0.8 mm/m, torsion max. 0.5 mm/m. A straightness of 0.1 mm/m can be produced on request.
Article ID: 64899455

Pillow block bearing unit BF 35 bore 35mm material steel black oxide finished
Material: Housing from steel, all surfaces machined, black oxide finished. On request: nickel-plated. With quality rolling bearing from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the support side. With one movable single row deep groove ball bearing with shields (2Z). With 6 mounting holes. Retaining ring for fixing on the spindle end is included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for fixed side: Pillow Block Bearing BK. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64200235

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 2.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

3-way ball valve, T-hole, Stainless steel 1.4408, G 1, DN 20, Operating temperature -20 °C to 180 °C, PN max. 63 bar
With L or T-bore, reduced bore.
Version for sealing on all sides with integrated ISO flange plate (ISO 5211).
The lever can be turned 360° to allow several switching variants.

Straight screw-in fitting, 7/8-14 UNF o., Pipe exterior Ø 20 mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel, UNF threat
Male connector, male thread UNF, heavy type

Kamlok quick-connect socket with interior thread, D type, Stainless steel 1.4401, G 2, for plug Ø 64 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Weld-on coupler 16, Steel with a bare metal surface ST 37-2, Continuous thread, Rp 3, Length 71 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Foot fastening, for round cylinder ISO 6432, Piston Ø 12-16, 1 piece
Foot model

T-multi-distributor »Blue Series«, 4-fold, rotating, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »click-clock«, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Round trapezoidal nut red brass Rg7 Tr.60 x 9 single-start left length 120mm outer diameter 100mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64386000

Spherical washer DIN6319 inner Ø 8,4mm outerØ 17mm for bolt diameter8mm stainless steel 1.4401 / AISI316
Material: 1.4401.* total height, together with conical seat DIN 6319.
Article ID: 65599458

Size : 57 x 15 mm
DECOMAGNEET RH 57x15 PVC WIT
SKU: GM14439
Stock: 0
Holding force: 115 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Pillow block bearing unit BF 35 bore 35mm material steel nickel plated
Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearing from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the support side. With one movable single row deep groove ball bearing with shields (2Z). With 6 mounting holes. Retaining ring for fixing on the spindle end is included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for fixed side: Pillow Block Bearing BK. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201235

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 3.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Active charcoal filter without differential pressure gauge, 0.005 mg/m³, G 1/2, Input pressure 4 - 16 bar, Temp. 5 °C to 60 °C
For adsorbing vaporous media.
A micro-filter must be connected upstream if dried air is not available.

GEKA threaded piece, Screw connection, rigid, KTW, bright brass, I.D. 13, Operating pressure max. 40 bar, Temp. -10 °C to 90 °C
GEKA-Kupplungen für Trinkwasser, Serie »GEKA-plus«, Messing blank, mit KTW-Zulassung

Reducing nipple, Short design, G 2 1/2 ET, G 1 1/2 IT, AF 80, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Pivoting bushing, ET, cyl. G 3/8 f.hose I.D. 6 nickel-plated brass/brass, working pressure 0.95-15bar, operating temp.-10°C-70°C

Bushing, round, G 3/8, Working pressure max. 20 bar, Stainless steel 1.4408

L-multi-distributor 2-fold »click-clock«, rotating, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Straight screw-on fitting, G 1/4 i., for hose 6/4 mm, AF 17, Working pressure max. 18 bar, nickel-plated brass