Push-in bulkhead L-connector »Blue Series«, M20x1, for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Stopper, Square, G 3/4, AF 17, Working pressure max. 20 bar, Stainless steel 1.4408

Check valve »lineonline«, Hose - hose, for hose Ø 8 mm, Operating pressure 0.5 to 12 bar
These valves ensure that compressed air only flows in one
(i.e. the desired) direction. The valve closes when inlet pressure is lost and maintains the working pressure that is present downstream.

Straight push-in fitting »Blue Series«, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Sprocket KRR with hub 16 B-1 1"x17.02mm 19 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305.

Teeth milled, pre-bored.

General dimensions:
B1 = 16,2 mm, c = 2,5 mm, r3 = 26 mm. Other dimensions: See the table.

Article ID: 10899119

Trapeziodal-threaded spindle DIN 103 Tr.40 x 7 x 1000mm long single-start right material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099040

Neodymium (NdFeB) 13 N
GM17499
SKU: GM17499
Stock: 0
Size: Ø12 mm
Height (L): 14.8 mm
Shear force: 5 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Flange for timing belt pulley thickness 0.5mm Ø 16 x 13 x 9.5mm steel zinc plated
Material: Steel, zinc-plated.Flanges for timing belt pulleys, for custom-made parts or serial production. For economical reason, normally the flanges are mounted only at the smaller pulley. Often, the flanges get fixed by beading: On a turntable, with a rolling tool, hub material will get shaped over the flange. A beading material overhang of 0.5mm is recommended. Sold by piece. Other sizes are available at short delivery time.
Article ID: 16010102

V-belt pulley material aluminium profile XPB, SPB and B (17) 1 groove nominal diameter 250mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15412500

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 23 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »variobloc« with PC container, Size 2, G 3/4, Input pressure max. 16 bar, Medium / ambient temp. max. 50 °C
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 25 bar, Ø63
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Round cylinder, ISO 6432, single-acting, Magnet, Piston Ø 8, Stroke 10, M5, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Single and double-acting cylinders, with magnetic piston.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Push-in L-fitting »Blue Series«, rotating, R 3/8 o., for hose exterior Ø 14 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, Soft sealing, G 1/2 o., Pipe exterior Ø 12 mm, PN max. 315 bar, AF1 22, AF2 27, galvanised steel
Male connector, parallel male thread and soft seal, light type

Push-in L-fitting »click-clock«, rotating, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Screw-on hose connector, G 1/8 i., for hose I.D. 6 mm, AF 14, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Trapeziodal-threaded spindle DIN 103 Tr.50 x 8 x 1000mm long single-start right material 1.4305 machined
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099050

Trapeziodal-threaded spindle DIN 103 Tr.28 x 5 x 1000mm long single-start right material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099028

Neodymium (NdFeB) 550 N
NDFEB POTM ø 88X8.5 DRB - CHIN
SKU: GM17510
Stock: 22
Size: Ø88 mm
Height (L): 17 mm
Shear force: 125 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Grub screw DIN 6332 with thrust point type SK with internal hexagon thread M6 length 50mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, burnished. Type SK: With internal hexagon. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400701

Triple-strand sprocket DRT 12 B-3 3/4x7/16" 27 teeth material steel for taper bush type 3020
Material:: Steel C45, not hardened. Product numbers ending with G are from grey cast iron GG25.Sprockets for taper bushes, for easy and fast mounting. The taper bush has to be ordered separately. General dimensions: B1 = 11,1 mm, B3 = 49,8 mm, c = 2,0 mm, r3 = 19 mm.Other dimensions: See the table.In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 13777127

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 25 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Quick-connect coupling I.D. 19, Bright brass, Sleeve I.D. 25, Operating pressure 0 - 35 bar, Med. / ambient temp. -20 °C to 100 °C
Single-sided blocking and quick connect coupling with extremely high flow performance.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 16 bar, Ø63
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking screw, Exterior hexagonal, G 2, AF 70, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Double threaded nipple, Hexagonal, G 1, AF 35, Working pressure max. 20 bar, Stainless steel 1.4408

Straight screw-in fitting, G 1/2 o., Pipe exterior Ø 12 mm, PN bar 630, A/F1 24, A/F2 27, galvanised steel
Male connector, parallel male thread, heavy type

Blow gun, Plastic, with short nozzle, Nipple ID 7.2 - 7.8, Operating temperature -20 °C to 45 °C, PN max. 10 bar
For blowing out and cleaning machines, engines, bearings, sliding surfaces, bores of all kinds, hollow parts, moulds, etc.
The compressed air guns are supplied in a blister package with Euro holes.

Straight push-in fitting »Blue Series«, R 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Round trapezoidal nut red brass Rg7 Tr.36 x 6 single-start left length 72mm outer diameter 75mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64383600

Neodymium (NdFeB) 180 N
NDFEB POT 66x8.5 DR BUS WIT RB
SKU: GM1750701
Stock: 0
Size: Ø66 mm
Height (L): 15 mm
Shear force: 75 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Spur gear made of polyketone die-cast with hub module 0.5 65 teeth tooth width 3mm outside diameter 33,5mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28106501

Trapeziodal-threaded spindle DIN 103 Tr.28 x 5 x 1000mm long single-start left material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099428

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 11 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.1-1 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 60 bar, Ø63
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 12, Stroke 30, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Bellows suction cup, Round 1.5 folds, Silicone material, »FGA«, ø14 mm, suitable connection nipple IT G 1/8, ET M5 / G 1/8
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very stiff top foldSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with?uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Push-in L-fitting »click-clock«, rotating, M5 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Counter-hinge model, ISO 15552, ISO 21287, Ø32
Counter-hinge model

Double threaded nipple 245, ET/ET, red., R 1/2, R 3/8, oper. temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Sprocket KRR with hub 08 B-1 1/2x5/16" 38 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305.

Teeth milled, pre-bored.

General dimensions:
B1 = 7,2 mm, c = 1,3 mm, r3 = 13 mm. Other dimensions: See the table.


Article ID: 10599138

Neodymium (NdFeB) 100 N
PM-RTB-N-RB-D43x6xM4
SKU: GM17505
Stock: 100
Size: Ø43 mm
Height (L): 10.5 mm
Shear force: 30 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Sliding disc spare part for couplings HF, HFD, HZ, HZD outside diameter 6.4mm black polyacetal
Material: Plastic acetal, black. Fitting to couplings HF, HFD, HZ and HZD. For each coupling, one sliding disc is required.

Article ID: 60123700

Splined shaft similar to DIN 14 profile KW 23X28 x 1000mm long stainless steel 1.4301
Material: Stainless steel 1.4301, cold drawn. Lengths in stock: 1000, 1500, 2000 and 3000 mm. Special lengths up to 6000 mm on request (some in stock). Tolerances: Straightness 0.8 mm/m, torsion max. 0.5 mm/m. A straightness of 0.1 mm/m can be produced on request.
Article ID: 64899403

Spur gear made of steel C45 without hub module 1.5 100 teeth tooth width 17mm outside diameter 153mm
Material: C45. Milled teeth. Tooth quality 8d25 DIN 3967. Pressure angle 20°.

Article ID: 22811100

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 12 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 3/8, Control range 0.1-2 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range -1 / 0 bar, Ø63
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 12, Stroke 40, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Male elbow, M12x1.5 tapered o., Pipe exterior Ø 6 mm, PN max. 630 bar, a/f1 17, a/f2 12, galvanised steel

Straight screw-in fitting POM, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

L-multi-distributor 2-fold »click-clock«, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

T-piece 130, IT/IT/IT, Rp 3/8, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Neodymium (NdFeB) 58 N
NDFE POT ZW RUB ø22X6 M4 DRBUS
SKU: GM17481
Stock: 6
Size: Ø22 mm
Height (L): 11.5 mm
Shear force: 15 N
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Sliding disc spare part for couplings HF, HFD, HZ, HZD outside diameter 19.1mm black polyacetal
Material: Plastic acetal, black. Fitting to couplings HF, HFD, HZ and HZD. For each coupling, one sliding disc is required.

Article ID: 60124200

Triple-strand sprocket DRT 12 B-3 3/4x7/16" 25 teeth material steel for taper bush type 2517
Material:: Steel C45, not hardened. Product numbers ending with G are from grey cast iron GG25.Sprockets for taper bushes, for easy and fast mounting. The taper bush has to be ordered separately. General dimensions: B1 = 11,1 mm, B3 = 49,8 mm, c = 2,0 mm, r3 = 19 mm.Other dimensions: See the table.In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 13777125

Ball screw spindle rolled 25x10mm length 670mm
Material: Bearing steel 100Cr6, No. 1.3505, rolled. Tensile strength 1570 N/mm², Brinell hardness 207 HB.• Rolled ball screw spindle.• To be combined with Maedler® flanged ball screw nuts and cylindrical ball screw nuts.• Pitch accuracy 52 μm/300 mm (T7).• Straightness 0,1 mm/m.• Special lengths and spindle end reworking against extra charge.Temperature range: -20°C to +80°C (for short time to +110°C).Note: Please refer to the mounting- and operating instruction. Before use, the nut and the spindle have to be lubricated. For grease lubrication, normal roller bearing grease is recommended. The lubricant consumption depends on the condition of use.
Article ID: 64025101

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 20 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.