Bush EP22 bore 12mm outer diameter 14mm length 12mm colour: white
Material: Thermoplast polybutylenterephthalat, modified (PBT + PTFE), white. Plain bearing bush made from thermoplastic with high dimension accuracy. Low friction. Specially suited for dry-running and for use at very low up to middle high temperatures. Good price/perfomance ratio with high dimension accuracy. Low friction, suitable also for lubrication-free running. Temperature range -50ºC bis + 170ºC.Operating Conditions: dry : very good. oiled: good. water: very good. field of aplication:Domestic appliances, chemical equipment, office equipment, sports equipment, automotive (pedals, steering, axes) and many more.

Article ID: 62721212

Double-strand sprocket ZRT 12 B-2 3/4x7/16" 28 teeth material steel for taper bush type 2517
Material:: Steel C45, not hardened. Product numbers ending with G are from grey cast iron GG25. Prepared for Taper clamping bush. General dimensions: B1 = 11,1 mm, B2 = 30,3 mm, c = 2,0 mm, r3 = 19 mm. Other dimensions: See the table. In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 12777128

Spur gear made of steel C45 with hub module 1.5 95 teeth tooth width 15mm outside diameter 145.5mm
Material: C45. Milled teeth. Tooth quality 8d25 DIN 3967. Pressure angle 20°.#
Article ID: 21809500

Spiral hose coupling set, Standard coupling I.D. 7.2, Polyamide, Hose Ø 8x6, PN at 23 °C max. 19 bar, Length 10 m
For safe and effective flow.

Thanks to their small coil diameter, they are compact, easy to handle and lightweight.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Active charcoal filter without differential pressure gauge, 0.005 mg/m³, G 1/4, Input pressure 4 - 16 bar, Temp. 5 °C to 60 °C
For adsorbing vaporous media.
A micro-filter must be connected upstream if dried air is not available.

Double threaded nipple 245, ET/ET, red., R 2 1/2, R 2, oper. temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 1, G 3/8, max. 16 bar, 0.5 - 3 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Push-in L-fitting »Blue Series« long, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Plug-in connector, I.D. 7.2-7.8, hardened / galvanised steel, Sleeve I.D. 8, Operating pressure max. 16 bar, Temp. -20°C to 100°C

Throttle check valve, Supply air throttle (»V«) push-in connector hose 8, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.

Double threaded nipple, Cylindrical, M14x1.5 o., M14x1.5 o., Brass
Previous design. Can be delivered as long as in stock.
After sale the delivery is made in new optimised geometry.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 72 teeth tooth width 20mm outside diameter 148mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195072

Trapeziodal-threaded spindle DIN 103 Tr.48 x 8 x 2000mm long single-start right material C15 rolled
Material: C15, rolled.

Tolerance zone 7e.

Length sawed (length may be longer than nominal length),
edges not broken.



Article ID: 64024800

Neodymium (NdFeB) 38 N
PM D22x6xM4
SKU: GM17482
Stock: 11
Size: Ø22 mm
Height (H): 6 mm
Attachment: M4
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

Flange bush EP22 bore 10mm outer diameter 12mm flange diameter 18mm length 7mm colour: white
Material: Thermoplast polybutylenterephthalat, modified (PBT + PTFE), white. Plain bearing flange bush made from thermoplastic with high dimension accuracy. Low friction. Specially suited for dry-running and for use at very low up to middle high temperatures. Good price/perfomance ratio with high dimension accuracy. Low friction, suitable also for lubrication-free running. Temperature range -50ºC bis + 170ºC.Operating Conditions: dry : very good. oiled: good. water: very good. field of aplication:Domestic appliances, chemical equipment, office equipment, sports equipment, automotive (pedals, steering, axes) and many more.

Article ID: 62731007

Slide set DZ 5321 SC slide length 700mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Self-close. Hold-in in closed position. Bracket Mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk / 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. Ordering details: e.g.: Product no. 649 042 30, Slides 5321 SC
Article ID: 64904270

5/2-way valve, manual, Manual lever, monostable, Connection G 1/8, Operating pre. 2.5 - 10 bar, Operating temp. -10 °C to 60 °C

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-25 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Check valve, DN 40, Brass, Metallic sealing, Operating temperature 0 °C to 90 °C, G 1 1/2, PN max. 10 bar
Applications: Water (no steam), neutral and non-corrosive liquid media, mineral oils.

Only suitable for liquid media. Flap valve closes by gravity, therefore only possible to be installed horizontally!

Round cylinder TP (ISO 6432) double-acting, Piston Ø 16, Stroke 200, M5, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled fitting, Pipe exterior Ø 5 mm, PN bar 100, AF1 12, AF2 9, galvanised steel
Union elbow, very light type

Sintered bronze silencer, Slot, G 3/8, Operating pressure max. 10 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Distributor strip, Outlets both sides, front and back, Input 2 x 1/4, Output 2 + 2 x 1/8, Aluminium
For easy assembly of compressed air taps (screw fittings, unions, couplings, etc.).
Optionally with 2, 3, 4, or 6 outlets on one side or both sides.

Screw-in hose connector, G 1/4 o., for hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 80 teeth tooth width 20mm outside diameter 164mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195080

Trapeziodal threaded spindle DIN103 Tr.50 x 8 x 2000mm long, single start right material C15, rolled
Material: C15, rolled.

Tolerance zone 7e.

Length sawed (length may be longer than nominal length),
edges not broken.



Article ID: 64025000

Sprocket KRR with hub 12 B-1 3/4x7/16" 21 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305.

Teeth milled, pre-bored.

General dimensions:
B1 = 11,1 mm, c = 2 mm, r3 = 19 mm. Other dimensions: See the table.


Article ID: 10799121

Ferrite 85 N
ANTI SLIP 75X50X11 RUBBER+ ZK
SKU: GM14123
Stock: 304
Size: 75 x 50 mm
Attachment: Self-adhesive
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

ES-bolt for Clevis DIN 71752 size 10 x 40 steel zinc-plated
Material: Steel zinc-plated. ES-Standard 01.* Size 20 is not part of the DIN.
Article ID: 63741000

V-belt pulley material aluminium profile XPB, SPB and B (17) 3 grooves nominal diameter 140mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley.

Article ID: 15431400

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 40, Stroke 125, G 1/4, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-60 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Plug-in connector for pushbutton safety couplings I.D.11, ISO 6150 C, Stainless steel, Sleeve I.D. 10, max. 16 bar, -20°C to 200°C

High performance silencer, Aluminium, G 1, Working pressure 0 - 10 bar, Operating temperature -10 °C to 70 °C

T-ring piece, for hollow screw G 3/8, for hose exterior Ø 10 mm, Working pressure max. 16 bar, Operating temp. -20°C to 70°C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Push-in L-fitting »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

T-piece 130, IT/IT/IT, Rp 2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight screw-in fitting POM, G 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 90 teeth tooth width 20mm outside diameter 184mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195090

Sprocket KRR with hub 16 B-1 1"x17.02mm 20 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305.

Teeth milled, pre-bored.

General dimensions:
B1 = 16,2 mm, c = 2,5 mm, r3 = 26 mm. Other dimensions: See the table.

Article ID: 10899120

Trapeziodal-threaded spindle DIN 103 Tr.52 x 8 x 2000mm long single-start right material C15 rolled
Material: C15, rolled.

Tolerance zone 7e.

Length sawed (length may be longer than nominal length),
edges not broken.



Article ID: 64025200

Ferrite 36 N
ANTI SLIP MAGN 60X30X7.5MM
SKU: GM14100
Stock: 74
Size: 60 x 30 mm
Attachment: Self-adhesive
Compact magnet systems with a steel shell and rubber coating for more shear force. Thanks to the shell of these magnet systems, the magnetic field strength increases and the pot magnets are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Rubberized pot magnets are perfectly suited for easily damaged surfaces, to prevent scratches. Due to the powerful neodymium system, you can rest assured they will remain securely in place.

Attach without drilling or screwing
Moveable, reusable and non-scratch
Deliverable from stock
High shear force

Composition and construction of pot magnets rubber coated

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell or pot ensures magnetic shielding. The bonding surface has a rubber coating for a higher shear force and to prevent scratches.

Operating temperature

When does loss of magnetic strength occur?

Neodymium rubber coated pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Holding forces

The specified holding forces are measured under optimum conditions: perpendicular, on a piece of grade 37 steel that has been ground flat with a thickness of 5 mm, without air gap.

hose clamp DIN 3017-1 type W4 stainless steel 1.4301 diameter range 32-50mm band width 9mm
Material: Stainless steel 1.4301 (type W4). High-performance hose clamps with worm gear thread, for fixing hoses, bellows and for similar usage. Band width 9 mm. Band thickness 0.6 mm. With hexagon screw head size 7 mm, with slot. Other sizes and versions on request.
Article ID: 63814050

Mounting bracket set DZ 634 for slides 9301, 9307 and 9308 bracket length 559mm 2 brackets with 4 bolts, nuts and washers
Material: Steel, zinc-plated. Sold by pair (1 x product no. = 1 pair of brackets). Bracket kits for side or bottom mounting. For selection see the one catalog page with selection table. Can be used for: Type 9301 / 9308. Each kit comprises: 2 brackets,and 4 hexagon screws 6.35mm with washers and nuts. per pair of slides, one pair of clip-on brackets is required. Recommended mounts: M4 screw. Temperature range: -20°C to +110°C. Ordering details: e.g.: Product no. 649 056 12, bracket accessory kit type 634, zinc plated, length 305mm.
Article ID: 64905622

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 50, Stroke 20, G 1/4, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-600 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Plug-in connector for pushbutton safety couplings I.D. 11, ISO 6150 C, Stainless steel, Sleeve I.D. 8, max. 16 bar, -20°C to 200°C

T-piece, 3x interior thread, G 1 1/2, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

GEKA blind coupling, for potable water, bright brass, Operating pressure max. 40 bar, Medium / ambient temperature -10 °C to 90 °C
GEKA-Kupplungen für Trinkwasser, Serie »GEKA-plus«, Messing blank, mit KTW-Zulassung

Push-in L-fitting »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Fitting 331, flat sealing, IT/ET, Rp/R 1 1/4, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Straight screw-in fitting POM, G 1/4 o., for hose exterior Ø 5 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 100 teeth tooth width 20mm outside diameter 204mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195100

Trapeziodal-threaded spindle DIN 103 Tr.60 x 9 x 2000mm long single-start right material C15 rolled
Material: C15, rolled.

Tolerance zone 7e.

Length sawed (length may be longer than nominal length),
edges not broken.



Article ID: 64026000

Round trapezoidal nut red brass Rg7 Tr.50 x 8 single-start right length 100mm outer diameter 90mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64335000

Size : 100 x 53 mm
GM14800
SKU: GM14800
Stock: 0
Holding force: 10 N
Material: Steel
Hang without drilling and screwing.Magnetic picture hangers hang objects up quickly. They work on any steel surface such as steel dividers, beams and cabinets. The surface remains intact. Tools are unnecessary.

Moveable, reusable and non-scratch
Attach without drilling or screwing
With anti-slip coating
Easy to install

Application

How can you safely hang a painting or framed photo on a steel partition wall?

If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution. With our magnetic picture hangers you can easily hang paintings, photos or other things.

The specially designed magnet systems with rubber film prevent scratches while also ensuring that products do not slide down. Not just magnetic force but also shear force ensure a safe product. With a hook, adhesive strip, threaded hole, screw threads or other fastening system, you can make any connection between product and magnet.

For hanging small objects such as photos, pictograms, drawings or LED strips, we sell self-adhesive magnetic tape.

Advantages

Magnets or Velcro and self-adhesives?

Magnets retain their holding power, unlike Velcro and self-adhesives. Furthermore, they leave no holes or other wall damage behind when moved or removed. Hanging without drilling and screwing saves time.

Composition

How is a picture hanger constructed?

The specially designed magnet systems are constructed of white painted steel with extra strong rubber magnetic foil. This prevents scratches and ensures the objects do not slide down. Not just magnetic force but also shear force ensure a safe product. The robust hook on which the object hangs is rounded and sits slightly forward. Our picture hangers are equipped with a tab in the bottom corner. They are easy to detach from the surface.

Knurled thumb screw 421 M6 x 20mm long set screw steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Threaded bolt: Steel, zinc plated, chromatised blue

Article ID: 65378400

Ball screw spindle rolled 32x5mm length 695mm
Material: Bearing steel 100Cr6, No. 1.3505, rolled. Tensile strength 1570 N/mm², Brinell hardness 207 HB.• Rolled ball screw spindle.• To be combined with Maedler® flanged ball screw nuts and cylindrical ball screw nuts.• Pitch accuracy 52 μm/300 mm (T7).• Straightness 0,1 mm/m.• Special lengths and spindle end reworking against extra charge.Temperature range: -20°C to +80°C (for short time to +110°C).Note: Please refer to the mounting- and operating instruction. Before use, the nut and the spindle have to be lubricated. For grease lubrication, normal roller bearing grease is recommended. The lubricant consumption depends on the condition of use.
Article ID: 64032051

V-belt pulley material aluminium profile XPA, SPA and A (13) 3 grooves nominal diameter 180mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15231800

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 40, Stroke 75, G 1/4, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.