Angled mini ball valve, Control panel integration, Brass chrome plated, Operating temp. -20°C to 80°C, G 3/8 IT, PN -0.99 - 20 bar

Double threaded nipple Cyl., G 2 1/2 o., G 2 1/2 o., AF 80, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Elbow 2a, short, 90°, IT/IT, Rp 1 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in fitting 45° »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-on hose connector, G 1 i., for hose I.D. 25, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Pipe double nipple 23, ET/ET, Black steel, R 3/8, Length 100.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Shrink disc ST-R stainless steel 1.4057 inner diameter 68mm
Material: Stainless steel 1.4057.For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.For medium torques.Quick mounting.Quick dismounting.No axial offset during mounting.Roughness: max, RZ=16 μm. Outer-Ø tolerance of hub = H9.Recommended tolerances for hub bore / shaft diameter: from dw Ø 30 = H6/j6; Ø 31-50 = H6/h6; Ø 51-65 = H6/g6.It is essential to degrease the contact surfaces of shaft and hub bore. Lubricate only the shrink disk and the screws with MoS2 and place it on the hub. Turn in the screws evenly by hand. Surface Roughness, Tolerances and Mounting Fasten the tensioning screws evenly, in sequence (not crossing over) until the fastening torque TA of the table is reached. To reach the value of TA, several fastening steps are required. The figures for T stated in the table were calculated for a lubricated shrink disk.
Article ID: 61599868

Holding force : 150 N
GM14817
SKU: GM14817
Stock: 0
Size: 125 x 65 mm
Material: Plastic, Stainless steel polished
A coat hook is essential. Magnetic coat hooks attach to any steel surface such as an office cabinet, warehouse rack, door or steel separation wall. Without drilling and screwing, you can quickly create a hook for a bag, coat and tie.

Attach without drilling or screwing
Moveable, reusable and non-scratch
With anti-slip coating

Application

Wherever steel is present

Hanging objects with magnets is incredibly fast. Moreover, you don't need a technician. You can create a wardrobe on any steel surface in no time at all. For example, on a steel office cabinet you can simply click the magnetic coat hook in place. Moving or removing is also done in a jiffy. No need to drill holes or use screws.
 
If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution.
 
For example, our coat hooks have been applied to steel beams, warehouse racks, doors, office cabinets, drawer blocks and dividers. But a magnetic hook also works great on a flat design radiator. That way, your wet clothes dry a lot faster.

Additional information

Magnetic force and shear force

A magnetic coat hook consists of a magnet system and a coat hook. The magnet system is made of ferrite or neodymium. Enough magnetic force to hang a jacket.
The force required to slide the hook over the surface is called shear force.
It is important in addition to magnetic force. That’s why our magnetic coat hooks are equipped with a special coating. This anti-slip coating on the back of the coat hook will ensure that the hook stays in place and does not slide down.
 
Our magnetic coat hooks have a high magnetic force and a high shear force. They have a load capacity of up to 18 kg.

Advantages

Magnets or Velcro and self-adhesives?

Magnets retain their holding power, unlike Velcro and self-adhesives. Furthermore, they leave no holes or other wall damage behind when moved or removed. If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution. With our magnetic coat hooks, you can easily hang your coat on any steel surface.

Trapeziodal-threaded spindle DIN 103 Tr.20 x 4 x 2000mm long single-start right material 1.4305 rolled
Material: 1.4305. Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length sawed (length may be longer than nominal length), edges not broken.
Article ID: 64099220

Precision steel shaft with shaft support low version Ø 16h6 x 1200mm long
Material: Steel 1.1213 (Cf53), hardened and ground, hardness 62±2 HRC, diameter tolerance ISO h6. Material support: Extruded aluminium. ength: Either 600 mm or 1200 mm. Delivery without mounting screws. Ready-to-install, supported linear shafts to be used with open linear bearings or open linear bearing units. The shafts are supported over the entire length. Unit can be shortened by the customer using an angle grinder. The shaft supports have internal threads to get mounted from the downside of the customer´s base plate. The required screw lenght depends also on the thickness of the base plate. Longer versions on request.
Article ID: 64741606

Spiral hose coupling set, Push button safety coupling I.D. 7.2, PU, Hose Ø 8x5, PN at 23 °C max. 12 bar, Length 7.5 m
These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-10 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Made of plastic PA6 GF 30.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

End and through distributor sockets made of high strength, glass fibre reinforced plastic (PA6 GF 30) with large range of applications.
Optionally 1 or up to 3 connection options as well as 2 thread sizes for internal and external threads (cannot be combined). For vertical carrying of media.

Universal distributor socket with up to 5 connection options. Suitable for vertical and/or horizontal carrying of media or the secure connection
(avoidance of existing components) of pressure reducer or maintenance device, for example.

All distributor sockets have a durable brass threaded insert, whose shape secures it against rotation and against axial shift due to its shape.

Suitable for media compressed air (ambient temperature -10 °C to 50 °C) or water (ambient temperature 1 °C to 50 °C). Drilling diagram dimensions
are identical for all distributor sockets, so a simpler and more flexible exchange between end, through and universal distributor sockets is ensured.

Caution:
Note that the distributor sockets should not be installed in danges zones. Danger zones are, for example, transport routes, escape routes, etc.

Wear part set, for stainless steel pressure regulator, 1.4571, G 1/4

Elbow 1a, short, 90°, IT/ET, Rp/R 1 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvan., DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in fitting »Blue Series«, G 1/4 i., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Adjustable straight fitting, cone seal, 360° swivel range, female nut M14x1.5 i., Pipe ext. Ø 6, PN max. 630 bar, galvanised steel

Thread plug nipple »click-clock«, M5 o., for hose exterior Ø 5 mm, Working pressure max. 16 bar, nickel-plated brass
By combining these parts with unions, union elbows and union tees, you can obtain all essential connecting variants and simultaneously reduce your warehousing costs.

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 10mm outer diameter 16mm length 10mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62332300

Holding force : 150 N
GM14818
SKU: GM14818
Stock: 0
Size: 125 x 65 mm
Material: Plastic, Stainless steel frosted
A coat hook is essential. Magnetic coat hooks attach to any steel surface such as an office cabinet, warehouse rack, door or steel separation wall. Without drilling and screwing, you can quickly create a hook for a bag, coat and tie.

Attach without drilling or screwing
Moveable, reusable and non-scratch
With anti-slip coating

Application

Wherever steel is present

Hanging objects with magnets is incredibly fast. Moreover, you don't need a technician. You can create a wardrobe on any steel surface in no time at all. For example, on a steel office cabinet you can simply click the magnetic coat hook in place. Moving or removing is also done in a jiffy. No need to drill holes or use screws.
 
If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution.
 
For example, our coat hooks have been applied to steel beams, warehouse racks, doors, office cabinets, drawer blocks and dividers. But a magnetic hook also works great on a flat design radiator. That way, your wet clothes dry a lot faster.

Additional information

Magnetic force and shear force

A magnetic coat hook consists of a magnet system and a coat hook. The magnet system is made of ferrite or neodymium. Enough magnetic force to hang a jacket.
The force required to slide the hook over the surface is called shear force.
It is important in addition to magnetic force. That’s why our magnetic coat hooks are equipped with a special coating. This anti-slip coating on the back of the coat hook will ensure that the hook stays in place and does not slide down.
 
Our magnetic coat hooks have a high magnetic force and a high shear force. They have a load capacity of up to 18 kg.

Advantages

Magnets or Velcro and self-adhesives?

Magnets retain their holding power, unlike Velcro and self-adhesives. Furthermore, they leave no holes or other wall damage behind when moved or removed. If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution. With our magnetic coat hooks, you can easily hang your coat on any steel surface.

V-belt pulley material aluminium profile XPB, SPB and B (17) 1 groove nominal diameter 280mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15412800

Spiral hose coupling set, Push button safety coupling I.D. 7.2, PU, Hose Ø 10x6.5, PN at 23 °C max. 11 bar, Length 3.0 m
These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-6 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Metal container, incl. NBR O-ring 30x2, for filter and filter regulator »multifix-mini« and »Standard-mini«

Compact cyl.ISO 21287,single-acting,female piston rod,retr.,magnet,PistonØ32,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Double threaded nipple, Hexagonal, R 1, AF 35, Working pressure max. 20 bar, Stainless steel 1.4408

1/3 Tube fitting, G 1 1/4 x 25 mm, taper seat, without collar, lightweight type, Brass with a bare metal surface

Adjustable straight fitting, cone seal, 360° swivel range, female nut M20x1.5 i., Pipe ext. Ø 12, PN max.630 bar, galvanised steel

Angled screw-in fitting not rotating, without O-ring, M5 o., for hose 5/3 mm, Working pressure max 18 bar, nickel-plated brass

Round trapezoidal nut red brass Rg7 Tr.52 x 8 single-start right length 104mm outer diameter 90mm
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).

Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64335200

Holding force : 180 N
GM14850
SKU: GM14850
Stock: 0
Size: Ø72 mm
Material: Stainless steel polished
A coat hook is essential. Magnetic coat hooks attach to any steel surface such as an office cabinet, warehouse rack, door or steel separation wall. Without drilling and screwing, you can quickly create a hook for a bag, coat and tie.

Attach without drilling or screwing
Moveable, reusable and non-scratch
With anti-slip coating

Application

Wherever steel is present

Hanging objects with magnets is incredibly fast. Moreover, you don't need a technician. You can create a wardrobe on any steel surface in no time at all. For example, on a steel office cabinet you can simply click the magnetic coat hook in place. Moving or removing is also done in a jiffy. No need to drill holes or use screws.
 
If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution.
 
For example, our coat hooks have been applied to steel beams, warehouse racks, doors, office cabinets, drawer blocks and dividers. But a magnetic hook also works great on a flat design radiator. That way, your wet clothes dry a lot faster.

Additional information

Magnetic force and shear force

A magnetic coat hook consists of a magnet system and a coat hook. The magnet system is made of ferrite or neodymium. Enough magnetic force to hang a jacket.
The force required to slide the hook over the surface is called shear force.
It is important in addition to magnetic force. That’s why our magnetic coat hooks are equipped with a special coating. This anti-slip coating on the back of the coat hook will ensure that the hook stays in place and does not slide down.
 
Our magnetic coat hooks have a high magnetic force and a high shear force. They have a load capacity of up to 18 kg.

Advantages

Magnets or Velcro and self-adhesives?

Magnets retain their holding power, unlike Velcro and self-adhesives. Furthermore, they leave no holes or other wall damage behind when moved or removed. If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution. With our magnetic coat hooks, you can easily hang your coat on any steel surface.

timing bar T5 72 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16297200

Precision shaft steel X46 stainless hardened min. 52 HRC and ground diameter 14h6 x 2000mm long cutting surface marked with red paint
Material: Stainless steel 1.4043 (X46Cr13), min. 52 HRC.Diameter tolerance: ISO h6.Dimension-stable up to +120°C.In lengths of 1 m and 2 m available ex stock. Fixed lengths can be delivered on request.
Article ID: 64799314

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 3/4, AF 32, Trigger pressure 2 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-4 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Wear part set, consisting of: Diaphragm, Valve cone and O-ring 68x3, for filter regulator »Standard«, Size 3, G 1/2

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ32,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Locking screw, Hexagonal socket without flange G 1/8 Stainl. st. 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Straight push-in fitting »metallica«, G 1/8 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
Push-in fittings, manufactured entirely in nickel-plated brass.
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Counter bearing, »CR« type for standard cylinder »SE«,»SAI«,piston Ø63, only in connection with pivoting fork fastening type »CB«
Counter-hinge model, »CR« type (only in conjunction with female hinge model, »CB« type)

Screw-in fitting for PVC pneumatic hose 8x10.2, Aluminium/plastic, Temperature -10 °C to 70 °C, PN -0,95 - 15 bar, G 1/4

Locknut DIN 981 KM4 M20x1 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388640

Holding force : 180 N
GM14851
SKU: GM14851
Stock: 0
Size: Ø72 mm
Material: Stainless steel frosted
A coat hook is essential. Magnetic coat hooks attach to any steel surface such as an office cabinet, warehouse rack, door or steel separation wall. Without drilling and screwing, you can quickly create a hook for a bag, coat and tie.

Attach without drilling or screwing
Moveable, reusable and non-scratch
With anti-slip coating

Application

Wherever steel is present

Hanging objects with magnets is incredibly fast. Moreover, you don't need a technician. You can create a wardrobe on any steel surface in no time at all. For example, on a steel office cabinet you can simply click the magnetic coat hook in place. Moving or removing is also done in a jiffy. No need to drill holes or use screws.
 
If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution.
 
For example, our coat hooks have been applied to steel beams, warehouse racks, doors, office cabinets, drawer blocks and dividers. But a magnetic hook also works great on a flat design radiator. That way, your wet clothes dry a lot faster.

Additional information

Magnetic force and shear force

A magnetic coat hook consists of a magnet system and a coat hook. The magnet system is made of ferrite or neodymium. Enough magnetic force to hang a jacket.
The force required to slide the hook over the surface is called shear force.
It is important in addition to magnetic force. That’s why our magnetic coat hooks are equipped with a special coating. This anti-slip coating on the back of the coat hook will ensure that the hook stays in place and does not slide down.
 
Our magnetic coat hooks have a high magnetic force and a high shear force. They have a load capacity of up to 18 kg.

Advantages

Magnets or Velcro and self-adhesives?

Magnets retain their holding power, unlike Velcro and self-adhesives. Furthermore, they leave no holes or other wall damage behind when moved or removed. If drilling or screwing in steel divider walls is not allowed or not possible, magnets are an excellent solution. With our magnetic coat hooks, you can easily hang your coat on any steel surface.

Standard three phase motor SM/I 230/400V 50Hz 0.18kW ca. 1340 rpm size 63 model B3 (For operating instructions please visit the download area of our website www.maedler.de)
Three phase 230/400V, 50 Hz. Protection class IP 55. Insulation class F. With cage rotor. Surface cooled. From 0.75 kW efficiency class IE3. The rated output stated below refers to continuous duty, an operating frequency of 50 Hz, a maximum ambient temperature of 40°C and an altitude 1000 m above sea level. Special versions on request: With non-standard voltage and frequency, dual speed, with electromagnetical DC spring-tension disc brake; AC capacitor motor 230 Volt.
Article ID: 43004300

Precision shaft steel CF53 hardened min. 59 HRC and ground diameter 14h6 x 2000mm long cutting surface marked with green paint
Material: Steel 1.1213 (CF53). Hardness min. 59 HRC. Ø 3mm made from material 100CR6. Diameter tolerance: ISO h6. Dimension-stable up to +120°C In lengths of 1 m and 2 m available ex stock. Fixed lengths can be delivered on request.
Article ID: 64751400

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 3/4, AF 32, Trigger pressure 3 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-40 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Distributor (for wall mounting), 5 connections G 1/2, per 1 connection right and left, 1 connection top, Bottom and front

Compact cyl.ISO 21287,single-acting,female piston rod, ext.,magnet,PistonØ32,Stroke15,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Screw-on hose connector, G 3/4 i., for hose I.D. 19 mm, AF 32, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Angled pivot fitting with O-ring, G 1/8 o., for hose 8/6 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Flange fastening, »FA« type for compact cylinder »ACP«, Piston Ø 63
Flange model, »FA« type

Thread plug nipple »click-clock«, G 1/8 o., for hose exterior Ø 5 mm, Working pressure max. 16 bar, nickel-plated brass
By combining these parts with unions, union elbows and union tees, you can obtain all essential connecting variants and simultaneously reduce your warehousing costs.

Locknut DIN 1804 type W M18x1.5 black finishing
Material: steel, black oxide finish, unhardened, unground.At these nuts, the stepped face with Ø d3 shall always be used as the bearing face.From size M45x1.5, the nuts have 6 slots.
Article ID: 65261800

Round Ø10 mm
GM1800501
SKU: GM1800501
Stock: 0
Holding force: 0,7 N
Design_Color: White
Whiteboard magnets are useful for hanging notes, drawings or other papers. They stick to whiteboards, plan boards, office cabinets, warehouse racking and anything containing steel.

Deliverable from stock
Available with extra strong magnet
Moveable, reusable and non-scratch
Coated magnets does not scratch
Steel and plastic version

Standard three phase motor SM/I 230/400V 50Hz 0.18kW ca. 1340 rpm size 63 model B5 (For operating instructions please visit the download area of our website www.maedler.de)
Three phase 230/400V, 50 Hz. Protection class IP 55. Insulation class F. With cage rotor. Surface cooled. From 0.75 kW efficiency class IE3. The rated output stated below refers to continuous duty, an operating frequency of 50 Hz, a maximum ambient temperature of 40°C and an altitude 1000 m above sea level. Special versions on request: With non-standard voltage and frequency, dual speed, with electromagnetical DC spring-tension disc brake; AC capacitor motor 230 Volt.
Article ID: 43006300

Corner safety valve, for liquids, Red brass, Operating temp. -10 °C to 110 °C, G 3/4, AF 32, Trigger pressure 1.2 bar
For non-toxic, non-flammable liquids.
No evaporation allowed when blowing off.
With diaphragm to protect the spring and with lifting device.
Type-tested, TÜV-SV. 749. F

Pressure transducer for general industrial applications, Non-linearity 0.5%, Measurement range 0-160 bar, G 1/4, CrNi steel 1.4404
Standard type for universal applications.
Suitable for electronic pressure measurements in the low and high-pressure ranges.

Distributor with 2 quick-connect couplings I.D. 7.2, »R26EMS«, Bright brass, G 1/2 ET, Operating pressure 0 - 35 bar
2-way distributor pieces made of brass with a bare metal surface, pre-assembled with quick disconnect coupling DN 7.2.
Available with threaded connection inside or outside.

Compact cyl.ISO 21287, single-acting, male piston rod ext.,magnet,PistonØ32,Stroke15,G1/8, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.