Rubber-metal MGE diameter 25mm height 20mm inner thread M6
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510253

Slide rail DZ 9301 slide length 762mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Lengths to 1.5 meters. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles ( to 217 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905130

Cranked handle DIN 468 Tg with fixed ball handle length 315mm type 1
Material: Crank body cast iron, plastic coated, textured finish.Handle steel, zinc-plated.Hand cranks: Square hole reamed true to gauge. Hub: Machined, cast iron burr precisely ground. Version F = with fixed handle Version D = with revolving handle

Article ID: 66803100

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 0.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.2-4 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

T-piece, exterior / exterior / exterior, R 1, Operating pressure max. 60 bar, Operating temp. max. 150 °C, nickel-plated brass

Dirt strainer, nickel-plated brass, Sieve insert mesh width 0.3 mm, Operating temp. -20°C to 110°C, G 1 1/2, DN 40, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Rotating fitting with kink protection spring, Brass, R 3/8, Hose Ø 12x9

Push-in L-fitting »Blue Series«, rotating, G 1/4 i., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Ball valve »valve line« Hand lever blue, Nickel-plated brass, IT/IT, G 1, DN 24, Operating temp. -20 °C to 120 °C, PN max 25 bar
Extremely economical standard ball valves made of nickel-plated brass for compressed air, water, non-toxic and non-corrosive gases and liquids.

Straight push-in fitting »Blue Series«, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

25 mm Steel
PM-TB-A-SS-D25x30
SKU: GM16007
Stock: 0
Holding force: 60 N
A: 7 mm
Height: 30 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 4 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.5-8 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Block valve pressure gauge, Bushing - Bushing, made of bright brass, G 1/2, PN 25 bar, AF 27, max. 50 °C, Test flange 40x5
It is useful to install a stopcock as a shut-off element between the pressure gauge and the pipe.
When the lever is set to the »blow out« position, the medium is discharged into the atmosphere.
Stopcocks with a test port allow pressure gauges to be simultaneously connected to the pipe.

Suspension chain for supply unit Airkraft

Rigid fitting with kink protection spring, Brass, G 1/8, Hose Ø 6x4

Push-in L-fitting »Blue Series«, rotating, Rc 1/4 i., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Blocking valve with plug connection »Blue series«, for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series«, rotating, R 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Bevel gear made of steel module 5 25 teeth i=1:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36211600

Silver steel DIN 175 115CrV3 ground and polished diameter 3h9 x 500mm long
Unhardened, strength 700 - 800 N/mm².

Subsequent hardening of short silver steel workpieces up to 64 HRC is well possible.

Fixed lengths can be delivered on request.


Article ID: 64700300

Round trapezoidal nut steel C35Pb Tr.52 x 8 single-start right length 104mm outer diameter 90mm
Material: Steel C35Pb.

Tolerance zone 7H.

Height = 2 x diameter.

Attention:
Steel nuts get very easily thightened on a spindle
made from steel or stainless steel.
This nuts are only for clamping, manual adjustments or as fastening nut.
Not suitable for drive systems.

Article ID: 64325200

32 mm Steel
PM-TB-A-SS-D32x35
SKU: GM16008
Stock: 0
Holding force: 160 N
A: 4 mm
Height: 35 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

timing bar AT10 34 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16893400

timing bar L 3/8" (9.525mm) 27 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A. Profile L = 3/8" = 9.525 mm.
Article ID: 18292700

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 4.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.5-10 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Reducer, cone seal, Pipe exterior Ø Female connector 20/6 mm, PN max. 400 bar, a/f1 27, a/f2 17, a/f3 36, galvanised steel
Reducer, with cone seal, heavy type

Round cylinder TP (ISO 6432) double-acting, Piston Ø 20, Stroke 160, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 2.7 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Screw-in hose connector, O-ring G 1/2 f.hose I.D. 12 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 80 °C
Suitable for air, water, oil, steam, etc.

Male elbow, NPT 3/8 o., Pipe exterior Ø 10 mm, PN max. 315 bar, a/f1 19, a/f2 17, galvanised steel
Male elbow, NPT thread, light type

Straight push-in fitting »Blue Series«, G 1/4 i., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Feather key DIN 6885 version A 12 x 8 x 55 mm material C45
Material: C45K.Version A.
Article ID: 61820100

Size : Ø12 mm
GM14418
SKU: GM14418
Stock: 0
Holding force: 55 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Splined shaft similar to DIN 14 profile KW 18X22 x 1500mm long stainless steel 1.4301
Material: Stainless steel 1.4301, cold drawn. Lengths in stock: 1000, 1500, 2000 and 3000 mm. Special lengths up to 6000 mm on request (some in stock). Tolerances: Straightness 0.8 mm/m, torsion max. 0.5 mm/m. A straightness of 0.1 mm/m can be produced on request.
Article ID: 64899431

Slide rail DZ 9301 slide length 457mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Lengths to 1.5 meters. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles ( to 217 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905118

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.5-16 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Seal set (wear part), for standard cylinder, Piston Ø 63, NBR seal
Set of gasket (parts subject to wear)

Pre-assembly supports for stainless steel cutting ring fitting, M26x1.5, Pipe exterior Ø 18 mm, AF 22, PN max. 315 bar
When stainless steel pipes are assembled, they must always be pre-assembled in a hardened pre-assembly adapter. They must never be assembled directly in the stainless steel adapter. The cones of the pre-assembly adapters are susceptible to wear and must therefore be inspected at regular intervals to check that they are still true to gauge.

We recommend using only seamless, soft-annealed, stainless steel pipes made of
1.4571 according to DIN 2391 Part 1 or DIN 2462, tolerance class D4/T3.

Pivoting fork fastening, »CB« type for short stroke cylinder »ACQ« and »ASQ«, Piston Ø 12
Female hinge model, »CB« type

Angled piece, interior/exterior, G/R 3/8, AF 17, Operating pressure max. 60 bar, Operating temp. max. 150°C, nickel-plated brass

Male elbow, NPT 1/2 o., Pipe exterior Ø 12 mm, PN max. 315 bar, a/f1 22, a/f2 19, galvanised steel
Male elbow, NPT thread, light type

Straight push-in fitting »Blue Series«, R 3/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Spur gear made of polyacetal resin die-cast with hub module 0.5 90 teeth tooth width 3mm outside diameter 46mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28109000

Size : Ø20 mm
PLAFONDMAGN.R20 STAAL MET HAAK
SKU: GM14420
Stock: 911
Holding force: 30 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.

Locking assembly COM-L bore 95mm size 95-135
Material: Steel. For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft. For very high torques. Self-centering. Slight axial offset possible during mounting. Concentricity: 0.02 to 0.04mm. Fit: Shaft h8, Hub H8. Surface roughness hub/shaft max. 12.5µm.

Article ID: 61551195

Spur gear made of steel C45 with hub module 2 60 teeth tooth width 20mm outside diameter 124mm teeth induction hardened
Material: Steel C45. Tooth area induction hardened, 54 +4 HRC. Teeth milled in quality 8d25 DIN 3967. The hardening sets the tooth quality to 10-11. Straight teeth. Pressure angle 20°.
Article ID: 23188160

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 6 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 3/8, Control range 0.1-1 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

3/2-way valve »Blue Series«, Plug connector, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, R 3/4, Pipe exterior Ø 22 mm, PN max. 160 bar, Stainless steel 1.4571

Pivoting fork fastening, »CB« type for short stroke cylinder »ACQ« and »ASQ«, Piston Ø 16
Female hinge model, »CB« type

Angled piece, interior / exterior, G/R 3/8, AF 17, Operating pressure max. 60 bar, Operating temperature max. 150 °C, Bright brass

Reducer, cone seal, Pipe exterior Ø Female connector 16/6 mm, PN max. 400 bar, a/f1 22, a/f2 17, a/f3 30, galvanised steel
Reducer, with cone seal, heavy type

Straight screw-in fitting, without O-ring, G 1/8 o., for hose 10/8 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Size : Ø25 mm
PLAFONDMAGN.R25 STAAL MET HAAK
SKU: GM14421
Stock: 21
Holding force: 40 N
Compact magnet systems with a hook and a shell of steel or plastic. With these strong magnetic hooks, you can attach all sorts of products to any steel surface. Check out our range of magnetic hooks and ceiling magnets in steel and plastic.

Attach without drilling or screwing
For presentation, display or hanging
Suitable for advertising and promotion
Steel and plastic version

Composition and construction of magnetic hooks

Good magnetic properties, affordably priced

Magnetic hooks have a plastic or steel shell with hook. The shell provides magnetic shielding. With these hook magnets, you can easily hang up to 20 kg. The raw material of the magnet - ferrite - is affordably priced compared with other types of magnet. Magnetic hooks are great value.
The hook of this pot magnet is screwed in the threaded bush or is part of the overall enclosure.

Operating temperature

When does loss of magnetic strength occur?

Ferrite magnetic hooks have an operating temperature of up to 200 °C. When heated to this temperature, the magnet loses 30 to 40% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Corrosion and application

Magnetic hooks do not corrode and are suitable for outdoor use.
The magnetic force is greater than shear force. These magnetic hooks are useful for steel slats in a suspended ceiling or other steel surfaces. They are less powerful with vertical use, for example on a steel cabinet door, partition wall or whiteboard. Here, we recommend magnets with a rubber coating or shell.