single direction thrust ball bearing 51100 inner Ø 10mm outer Ø 24mm height 9mm
Material: Bearing steel.Thrust Ball Bearings for single direction in brand quality from MAEDLER®.For axial load (no radial load permitted).Usable for high speed.These bearings exist from lose parts: Shaft ring (with ground bore), housing ring (with ground outer diameter and bigger bore) and ball cage with balls. The rings must not be confused with each other.Temperature range: -30°C to +125°C. Other versions or sizes on request.

Article ID: 51100-MAE

timing bar HTD 5M 60 teeth length 200mm material aluminium
Material: Aluminium 6082-T6, UNI 9006.

Article ID: 17296000

V-belt pulley material aluminium profile XPZ, SPZ and Z (10) 2 grooves nominal diameter 250mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15022500

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 1 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

2/2-way solenoid valve brass, NO, force pilot operated, 24 V DC, Rp 3/8, NBR, Medium temp. -20 °C to 85 °C, PN 0 - 9 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Standard pressure gauge, front ring, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 40 bar, Ø 40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight screw-in fitting, G 1/8 o., for hose 8/10 mm, AF 19, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Replacement filter element for compact ejector type »Compact pump«, with nozzle size 1.5 mm
Replacement filter element

Plastic silencer with granulate filling, G 1/2, Operating pressure max. 12 bar, Operating temperature -20 °C to 70 °C
With granular filling, self-cleaning.
The spherical shape of the granules allows very fine dust to escape in addition to air.
Higher blow-off rate.

Air gun with extension pipe, Plastic, Temperature range -20 °C to 50 °C, PN max. 10 bar, Sleeve I.D. 13
For blowing out and cleaning machines, engines, bearings, sliding surfaces, bores of all kinds, hollow parts, moulds, etc.

Double threaded nipple »value line«, G 1/4, G 1/2, AF 24, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

8 mm Steel
PM-TB-A-SS-D8x12
SKU: GM16002
Stock: 11
Holding force: 4 N
A: 3 mm
Height: 10 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Flanged bush slotted version 16 x 18 / 24 x 17 mm
Main characteristics Self lubricating and maintenance free, ready to install. Perfectly suited for lower sliding speeds. Low wear, low friction coefficient, no 'stick slip'. Perfectly suited for circular, swivelling and partly for axial movement. Can be used at extremely high bearing loads. No moisture absorption. High corrosion Construction Tin-plated steel back (incl. edges). Multi-porous bronze layer, sliding surface PTFE-lead-compound. Technical data Stat. surface pressure: max. 250 N/mm² Dyn. bearing load: max. 56 N/mm² Friction coefficient: 0.03 - 0.20 Sliding speed: max. 2 m/s Temperature range: -195°C to 280°C Therm. conductivity: 40 W/K*m Recommended mounting tolerances Housing bore H7, shaft tolerance up to 55 Ø f7 above 55 Ø h8 Paired contact surface Recommended: hardened contact surfaces with a surface roughness of Rz3 and finer.

Article ID: 62411620

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 1.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 2-part »multifix«, Metal container, Viewing tube, Size 3, G 3/4, Input pressure max. 20 bar, Control range 0.5-10 bar
Two-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.

Standard pressure gauge, front ring, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range -1 / 0 bar, Ø 40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Double threaded nipple, R 2 o., R 2 o., AF 62, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150°C
Suitable for air, water, oil, steam, etc.

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, G 1/4 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Push-in T-connector »Blue Series«, reducing, for hose exterior Ø 2x10/1x8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-on hose connector, G 1 i., for hose I.D. 32 mm, AF 38, Brass, Max. working pressure 25 bar, Max. operating temperature 150°C

Bushing with exterior hexagonal, reducing, G 1/8 i., G 1/4 i., Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Trapeziodal-threaded spindle DIN 103 Tr.20 x 4 x 1000mm long single-start right material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099020

Locking assembly COM-B bore 85mm size 85-106
Material: Steel. Self-centering clamping bush for small hub
diametres. For medium torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61568500

10 mm Steel
PM-TB-A-SS-D10x16
SKU: GM16003
Stock: 0
Holding force: 8.5 N
A: 6 mm
Height: 16 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Protection cap for pillow bearings TUCP TUCF TUCFL 207 closed design thermoplast black
Material: Thermoplast PBT, black.Open Design, with sealing, for shaft side or closed design.The caps fit only on the one bearing side with the setscrews and can get clipped on by hand by the customer.
Article ID: 62555335

V-belt pulley material aluminium profile XPA, SPA and A (13) 3 grooves nominal diameter 280mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15232800

Worm wheel made of cast iron GG25 module 4 26 teeth double-thread right hand
Material: GG25, with milled out, hollow teeth. With double-sided hub. Double-thread worm gears to be paired with double-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,67. Not self-locking.
Article ID: 31051100

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 2 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Compact cylinder »ACP«, double-acting, Piston Ø 100, Stroke 65, Connection G 1/4, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Standard pressure gauge, front ring, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 25 bar, Ø 40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Mist oiler »variobloc« with polycarbonate container, Size 1, G 1/4, Input pressure max. 16 bar, Medium / ambient temp. max. 50 °C
Proportional lubricators, oil can be filled under pressure.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, R 1/4 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Push-in L-fitting »click-clock«, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Trunnion mounting, »CA/CB« type for compact cylinder »ACP«, Piston Ø 40
Male hinge model, »CA« type / Female hinge model, »CB« type

Screw-in hose connector, G 1/4 o., for hose I.D. 4, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

13 mm Steel
PM-TB-A-SS-D13x18
SKU: GM16004
Stock: 0
Holding force: 12 N
A: 6 mm
Height: 18 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Knurled thumb screw 421 M4 x 30mm long set screw steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Threaded bolt: Steel, zinc plated, chromatised blue

Article ID: 65377500

timing bar T10 34 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16493400

Trapeziodal-threaded spindle DIN 103 Tr.20 x 4 x 1000mm long single-start left material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099420

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 5.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.1-1 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Mini ball valve, Stainless steel 1.4401, IT/ET, Operating temperature -20 °C to 120 °C, G 1/4, DN 7, PN max. 63 bar

Mist oiler »variobloc« with polycarbonate container, Size 1, G 3/8, Input pressure max. 16 bar, Medium / ambient temp. max. 50 °C
Proportional lubricators, oil can be filled under pressure.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M14x1.5 i., Pipe ext. Ø 6, PN max. 630 bar, galvanised steel

Push-in L-fitting »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in T-connector »Blue Series«, reducing, for hose exterior Ø 2x4/1x6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

16 mm Steel
PM-TB-A-SS-D16x20
SKU: GM16005
Stock: 0
Holding force: 20 N
A: 6 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Grub screw DIN 6332 with thrust point thread M8 length 40mm steel strength 5.8 black oxide finished
Material: Steel quality 5.8, turned, thrust point hardened, black oxide finish. Type S: With slot. Assembly: Turn thrust screw into thrust pad. The thrust pad has to be held thus that the spring retainer lies in the recess with its open side at the bottom. Now tilt the grub screw as far as possible towards the open side of the ring and press it in. To be combined with the thrust pads DIN 6311 on the same catalog page (product no. 65410600-65414000).
Article ID: 65400900

slide rail DP 9301 E slide length 762mm
Material: Slide elements: Cold rolled steel, zinc plated, with organic-mineral coating for high corrosion resistance. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide).Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Slides sold separately. Good corrosion resistance. Lubricated with grease for food. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note: Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905730

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 9.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.1-2 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Standard pressure gauge, front ring, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 1.6 bar, Ø 40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Basic ejector »SBP«, High under-pressure, Silencer, Nozzle size 1.5 mm, Compressed air / vacuum connection 6/8 mm, PN max. 4.5 bar
Purely pneumatic vacuum generator that operates on the Venturi principle.
Compressed air enters the ejector at A and flows through the nozzle B. This results in a vacuum immediately behind the nozzle outlet, and air is drawn in through the vacuum inlet D. This air and the driving air leave the ejector via the silencer C.

Properties:
Vacuum generator without control valves or system monitoring functions,?with a high maximum vacuum value (85%)No moving parts, which means no wear and no maintenanceMaximum suction capacity with minimum compressed air consumptionMinimum size, low weightFor decentralised vacuum generation in highly dynamic processes

Applications:
For universal use in lightweight gripper systems to handle air-tight workpieces
as well as for automatic separation systems, e.g. in the plastics, electronics
and packaging industries. Also ideal for the construction of ejector blocks for
decentralised control of suction pads.

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M20x1.5 i., Pipe ext. Ø 12, PN max. 630 bar, galvanised steel

Straight push-in bulkhead fitting »Blue Series«, M14x1, Rc 1/8 i., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »Blue Series«, R 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Trapeziodal-threaded spindle DIN 103 Tr.16 x 4 x 1500mm long single-start right material 1.4305 rolled
Material: 1.4305.

Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length
sawed (length may be longer than nominal length), edges not broken.

Article ID: 64099116

20 mm Steel
PM-TB-A-SS-D20x25
SKU: GM16006
Stock: 15
Holding force: 40 N
A: 5 mm
Height: 25 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.