Rod end GEW DIN 12240-4 series E internal thread M39x3 left maintenance-free
Material: Outer part: Zinc-plated. Boreholes up to 10mm: free-cutting steel, turned. From boreholes 12mm: Steel C45, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining. Small version. Dimensions according to DIN 648 / 12240-4 series E. Thread either right-handed or left-handed. Rod ends for high radial and axial alternating loads. Steel on PTFE-lining. Maintenance-fee. Sliding speed up to 10 m/min.
Article ID: 63434000

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 7.7 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 6x4, PN at 20 °C max. 27 bar, natural (milky), Roll of 100 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Extension pipe for basic air guns, with standard nozzle, 300 mm straight

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ32, Stroke50,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure gauge fitting, G 3/8 i., Pipe exterior Ø 12 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Push-in L-fitting »Blue Series«, rotating, R 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Throttle check valve, Discharge throttle (»C«) threaded connection G 1/4 i., G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Straight screw-on fitting »value line«, G 1/8 i., for hose exterior Ø 8 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Neodymium (NdFeB) 25 N
PM-BA-N-BR-D8h6x20
SKU: GM17302
Stock: 40
Diameter: 8 mm
A: 10 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Hollow knurled nut 420 M4 bush steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Bush: Steel, zinc plated, chromatised blue.

Article ID: 65375400

Rod end GEW DIN 12240-4 series E internal thread M45x3 right maintenance-free
Material: Outer part: Zinc-plated. Boreholes up to 10mm: free-cutting steel, turned. From boreholes 12mm: Steel C45, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining. Small version. Dimensions according to DIN 648 / 12240-4 series E. Thread either right-handed or left-handed. Rod ends for high radial and axial alternating loads. Steel on PTFE-lining. Maintenance-fee. Sliding speed up to 10 m/min.
Article ID: 63415000

V-belt pulley material aluminium profile XPZ, SPZ and Z (10) 1 groove nominal diameter 315mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15013100

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 7.8 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 6x4, PN at 20 °C max. 27 bar, blue, Roll of 100 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Double threaded nipple G 1 1/4 o., G 1 1/4 o., AF 50 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ25, Stroke75, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled fitting, Pipe exterior Ø 12 mm, PN max. 315 bar, AF1 22, AF2 17, galvanised steel
Union elbow, light type

Angled screw-in fitting, rotating, with O-ring, G 1/4 o., for hose 8/6 mm, Working pressure max. 18 bar, nickel-plated brass

Throttle valve, Both sides throttling (»B«) Threaded connection G 1/4 IT, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Straight screw-on fitting »value line«, G 1/8 i., for hose exterior Ø 4 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Neodymium (NdFeB) 70 N
PM-BA-N-BR-D13h6x20
SKU: GM17304
Stock: 18
Diameter: 13 mm
A: 6 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Hollow knurled nut 420 M5 bush steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Bush: Steel, zinc plated, chromatised blue.

Article ID: 65375500

Rod end GEW DIN 12240-4 series E internal thread M45x3 left maintenance-free
Material: Outer part: Zinc-plated. Boreholes up to 10mm: free-cutting steel, turned. From boreholes 12mm: Steel C45, forged. Inner ring: Roller bearing steel 100Cr6, hardened HRC 62+/-1, ground and polished. Bearing race: Steel with PTFE-lining. Small version. Dimensions according to DIN 648 / 12240-4 series E. Thread either right-handed or left-handed. Rod ends for high radial and axial alternating loads. Steel on PTFE-lining. Maintenance-fee. Sliding speed up to 10 m/min.
Article ID: 63435000

Triple-strand sprocket DRT 12 B-3 3/4x7/16" 19 teeth material steel for taper bush type 2012
Material:: Steel C45, not hardened. Product numbers ending with G are from grey cast iron GG25.Sprockets for taper bushes, for easy and fast mounting. The taper bush has to be ordered separately. General dimensions: B1 = 11,1 mm, B3 = 49,8 mm, c = 2,0 mm, r3 = 19 mm.Other dimensions: See the table.In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 13777119

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 8.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 6x4, PN at 20 °C max. 27 bar, black, Roll of 100 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Joint head »UNIT« type for short stroke cylinder »ACQ«/»ASQ«, Piston Ø 20, Piston rod thread M5x0.8 i., without lubrication nipple
Rod eye model, »UNIT« type (incl. threaded adapter)

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ32, Stroke50, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Drip cap polycarbonate

T screw-in fitting, rotating, with O-ring, G 1/8 o., for hose 8/6 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Throttle valve, Both sides throttling (»B«) push-in connector hose 6, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Straight screw-in fitting, R 1/8 o., Pipe exterior Ø 6 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Neodymium (NdFeB) 150 N
PM-BA-NB-BR-D16h6x20-B
SKU: GM17305
Stock: 7
Diameter: 16 mm
A: 2 mm
Height: 20 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Knurled thumb screw 421 M6 x 16mm long set screw steel zinc plated
Material: Head: Plastic thermoplast (polyamide) black, glossy finish Threaded bolt: Steel, zinc plated, chromatised blue

Article ID: 65378200

Round flange trapezoidal nut Tr.40 x 7 single-start right material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Tolerance zone 7H.
Article ID: 64414000

timing bar T5 50 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16295000

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 17.5 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 100, Stroke 25, G 1/2, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Joint head, »UNIT« type, for compact cylinder »ACP«, Piston Ø 20-25, Piston rod thread M5x0.8 i., without lubrication nipple
Rod eye model, »UNIT« type (incl. threaded adapter)

Compact cyl.ISO 21287,single-acting,female piston rod,retr.,magnet,PistonØ32,Stroke10,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered plug-in nipple DN 6, with blocking valve, ET, Brass 2.0401, M14x1.5, Operating pressure max. 15 bar, Temp. -20°C to 160°C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Hose clamp, Malleable cast iron, 2-part, with loose tongues, Safety jaws, Clamping range 28 - 32 mm, for hose I.D. 19 (3/4")

Throttle check valve, Discharge throttle (»C«) quick connector Hose 10/8, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.

Straight connector »value line«, for hose 6/4 mm, AF 12, Operating pressure max. 18 bar, nickel-plated brass
Unions
Nickel-plated brass, »value line« Series

Neodymium (NdFeB) 280 N
PM-BA-N-BR-D20h6x25
SKU: GM17306
Stock: 0
Diameter: 20 mm
A: 5 mm
Height: 25 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Star knob similar to DIN 6336 type E thread M6
Material: Plastic Thermoplast (Polyamide), impact resistant, black, matt finish. Bush: Steel, zinc-plated, chromated blue. Version C: with blind hole H7. Version E: with thread (tapped blind hole). The full diameter of the contact surface is made from Steel. The protruding steel bush allows a perfect cross-pin connection.
Article ID: 66133201

Double-strand sprocket ZRT 10 B-2 5/8x3/8" 28 teeth material steel for taper bush type 2012
Material:: Steel C45, not hardened. Product numbers ending with G are from grey cast iron GG25. Prepared for Taper clamping bush. General dimensions: B1 = 9,1 mm, B2 = 25,5 mm, c = 1,6 mm, r3 = 16 mm. Other dimensions: See the table. In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 12677128

Safety valve, High performance design, Brass, Operating temp. -40 °C to 200 °C, G 1/2, AF 27, Trigger pressure 2.8 bar
For compressed air and non-toxic, non-flammable gases, cannot be used for liquids due to free blow-off, not suitable for steam.
These valves are TÜV approved and have a TÜV type test number.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 100, Stroke 80, G 1/2, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Joint head »UNIT« type for short stroke cylinder »ACQ«/»ASQ«, Piston Ø 25, Piston rod thread M6x1i., with lubrication nipple
Rod eye model, »UNIT« type (incl. threaded adapter)

Compact cyl.ISO 21287, single-acting, male piston rod,retr.,magnet,PistonØ32,Stroke10,G1/8,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-on fitting G 3/8 i., for hose 8/10 mm, AF 22, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Angled hose fitting supports, for hose I.D. 25 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Throttle valve, Both sides throttling (»B«) quick connector Hose 10/8, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Angled screw-in fitting »value line«, R 3/11 o., for hose 6/4 mm, AF 8, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Tensioning element stainless steel size 3 810 N
Material: Stainless steel 1.4301 or 1.4308.

The design of this tensioning element is identical to the standard version.




Article ID: 14099803

Bevel gear made of steel module 5 30 teeth i=1:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears, with the same module and the same number of teeth.
Article ID: 36212000

Neodymium (NdFeB) 450 N
PM-BA-N-BR-D25h6x35
SKU: GM17307
Stock: 0
Diameter: 25 mm
A: 7 mm
Height: 35 mm
Compact magnet systems with a steel shell with h6 fit tolerance. These pot magnets are suitable for gluing, pressing and shrinking. Thanks to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attraction surface; this prevents the spread of the magnetic field.Pot magnets with h6 fit tolerance are available in various sizes and types such as neodymium, samarium cobalt and AlNiCo.

Deliverable from stock
Available in various qualities
Editing without losing magnetic power

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.
 

Operating temperature

What temperature does magnet strength loss occur at?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.
 
Tooling the magnet without loss of tensile force:
The magnet strength remains the same when the magnet system is shortened down to a maximum value of A. See the specified value for the relevant item.

Star knob screw similar to DIN 6336 type ST Ø25mm M5 x 10
Material: Thermoplast Polyamide PA. Threaded bolt: steel, zinc-plated, chromated blue.
Article ID: 66182510