Bi-metallic thermometer for heating, Connection rear, G 1/2, Immersion shaft length 100 mm, Ø 80 mm, Display range 0 °C to 120 °C
Applications: Heating, plumbing, universal.

Reducing nipple, Long type G 1/8 o., G 1/4 i., AF 17 Nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Chain tensioner SPANN-BOX® size 1 long high tensioning force 08 B-3 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040735

Locking assembly COM-B bore 80mm size 80-100
Material: Steel. Self-centering clamping bush for small hub
diametres. For medium torques. Self-Locking.
Fit: Shaft h8. Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange until the flange is
released.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61568000

Samarium-Cobalt (SmCo) 150 N
PM-TB-S-SG-D25x7x14xM4
SKU: GM17207
Stock: 0
Diameter (D): 25 mm
Height (H): 7 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Pillow block bearing unit BK 30 bore 30mm material steel black oxide finished
Material: Housing from steel, all surfaces machined, black oxide finished. With quality rolling bearings from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the fixed side. With two angular contact ball bearings, lightly preloaded, with seals. With 8 mounting holes. Locknut and distance bushes are included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for support side: Pillow Block Bearing BF. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64200130

Rubber-metal MGE diameter 150mm height 75mm inner thread M16
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68511505

Stainless steel ball valve, 2-piece, IT/IT thread, G 1 1/4, DN 32, Operating temperature -20 °C to 180 °C, PN max. 63 bar

Precision pressure regulator without pressure gauge, G 3/8, Control range 0.05 - 3 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Plug-in connector for swing and swivel safety coupl. I.D. 11, ISO 6150 C, Steel, Sleeve I.D. 10, max. 25 bar, Temp. -20°C to 100°C

Vacuum pressure switch, Brass, 42 V, Changeover contact, Ambient temp -25 °C to 85 °C, G 1/8, Setting range 20 - 800 mbar
For liquid, non-corrosive and gaseous media. Easy to adjust, even under pressure.
Can be integrated in any mounting position. Pressure adjustment by means of a hexagon-head screw.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 6 bar/90 psi, Ø 63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Flange fastening, ISO 6432, Piston Ø 12 to 16, galvanised steel, 1 piece
Flange model

Kamlok quick-connect plug with exterior thread, F type, Stainless steel 1.4401, R 1, Plug Ø 37 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Reducing nipple, Long type, M5 o., M5 i., AF 7, Nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Locknut DIN 981 KM0 M10x0,75 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388630

Chain tensioner SPANN-BOX® size 1 long high tensioning force 10 B-3 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040736

Samarium-Cobalt (SmCo) 220 N
PM-TB-S-SG-D32x7x15.5xM5
SKU: GM17208
Stock: 0
Diameter (D): 32 mm
Height (H): 7 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Crane wheel made of C 45 with axle shaft diameter 100mm
Especially suited for heavy-duty applications, e.g. electrically controlled gates. Precisely turned from solid material; with fully sealed precision bearings. Wheel body black oxide finish. Product No. 776 004 00 and 776 005 00 with square running surface and single bearing, Product No. 776 006 00 to 776 016 00 with convex running surface and double bearing. Delivery includes all mounting material needed; axle bolt at running surface Ø 35 and 45 mm with external thread, serrated washer and hexagon nuts, other sizes with internal thread, 6 hexagon screws and washers DIN ISO 7093-1. * The wheel loads stated are derived from the dimensions and temperatures listed in the roller bearing cataloques. For product No. 776 004 00 and 776 005 00 these values are valid at a maximum operating temperature of 90°C; for higher continuous temperatures, please inquire first. ** Rails are not part of our stock. Please inquire at your steel supplier.
Article ID: 77601000

Slide set DZ 5321 SC slide length 350mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Self-close. Hold-in in closed position. Bracket Mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk / 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. Ordering details: e.g.: Product no. 649 042 30, Slides 5321 SC
Article ID: 64904235

Push-in L-fitting, rotating, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Standard cylinder, ISO 15552, double-acting, Piston Ø 80, Stroke 200, G 3/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Plug-in connector for swing and swivel safety coupl. I.D. 11, ISO 6150 C, Steel, Sleeve I.D. 13, max. 25 bar, Temp. -20°C to 100°C

Block valve pressure gauge, Taps - tension sleeve, 1.4571 housing, 1.4305 tension sleeve, G 1/2, PN 25 bar, AF 27, max. 50 °C
It is useful to install a stopcock as a shut-off element between the pressure gauge and the pipe.
When the lever is set to the »blow out« position, the medium is discharged into the atmosphere.
Stopcocks with a test port allow pressure gauges to be simultaneously connected to the pipe.

Standard press. gauge »pressure line« Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range -1/0 bar/-14.5 psi, Ø63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight push-in connector »metallica«, for hose exterior Ø 8 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 150 °C
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Bulkhead elbow connector, Pipe exterior Ø 8 mm, PN max. 630 bar, a/f1 19, a/f2 22, a/f3 14, galvanised steel
Bulkhead elbow connector, heavy type

Locking screw, Hexagonal socket and flange G 1/2 AF 10 nickel-plated brass Max. working pressure 25 bar Max. operating temp.150 °C
Suitable for air, water, oil, steam, etc.

Locknut DIN 981 KM1 M12x1 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388632

Chain tensioner SPANN-BOX® size 1 long high tensioning force 12 B-3 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040737

Ferrite 4 N
PM-TB-F-SG-D10x4.5x11.5xM3
SKU: GM16501
Stock: 0
Diameter (D): 10 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Sliding hub FS torque adjustable 50-300 Nm with pilot bore 19H8 outer diameter 127mm max. bore: 40mm bush length 16mm
Material: Hub: Steel, zinc-plated and passivated. Spring: Steel, black. The sliding hubs can be delivered ex stock, pre-drilled with standard bush length. Required bush length: The required bush length depends on the width of the component to be joined. Up to Prod. No. 612 006 00: Bush length 4.2 mm for a component width of 5.3 to 6.0 mm. From Prod. No. 612 010 00: Bush length in mm = 1.5 x G + C. Other bush lengths and customized bores or feather-key grooves against extra charge. At sizes 120 and 180, the lock washer is a round plate, without edges.
Article ID: 61205000

Pillow block bearing unit BF 30 bore 30mm material steel nickel plated
Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearing from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the support side. With one movable single row deep groove ball bearing with shields (2Z). With 6 mounting holes. Retaining ring for fixing on the spindle end is included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for fixed side: Pillow Block Bearing BK. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201230

5/2-way foot valve, monostable, non-engaging with foot guard, Connection G 1/4, Operating pressure 2.5-10 bar, Temp. -10°C to 60°C
Foot-operated valves, 3/2- and 5/2-way types, bistable or monostable (non-latching).

Storz reducer, Aluminium, Storz size 100, Tappet distance 115 mm, Flange DN 100, Operating pressure max. 16 bar
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Plug-in connector for swing and swivel safety coupl. I.D. 11, ISO 6150 C, Steel, Sleeve I.D. 16, max. 25 bar, Temp. -20°C to 100°C

Ball valve »valve line« Hand lever blue, Nickel-plated brass, IT/IT, G 2, DN 45, Operating temp. -20 °C to 120 °C, PN max 25 bar
Extremely economical standard ball valves made of nickel-plated brass for compressed air, water, non-toxic and non-corrosive gases and liquids.

Standard pressure gauge »pressure line« Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0-1.6 bar/23 psi, Ø63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in L-fitting »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

T-piece 130, IT/IT/IT, Rp 2, T-branch reducing Rp 1 1/2, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Screw-in hose connector, G 1/4 o., for hose I.D. 9 mm, AF 17, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Locknut DIN 981 KM2 M15x1 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388634

Ferrite 10 N
PM-TB-F-SG-D13x4.5x11,5xM3
SKU: GM16502
Stock: 0
Diameter (D): 13 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

timing bar AT5 64 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16696400

Ball flange bearing SSUCF 207 bore 35mm housing and bearing stainless steel
Material: Housing: Stainless steel 1.4305 (X5CrNi18-10, AISI 304). Rolling bearing: Stainless steel 1.4125 (X105CrMo17, AISI 440 C), lubricated with grease FM 222 for food processing machinery, with registration FDA, CIFA, KPF2K-20, NSF H1. Temperature range: -20°C to +90°C (for short time up to +120°C).With 4 mounting holes.The rolling bearing can be swiveled when mounting to compensate shaft misalignement.The shaft will get fastened with 2 setscrews. Lubricated for life at normal operating conditions. Re-lubricating is possible.Delivery with stainless steel grease nipple.
Article ID: 62699035

5/2-way foot valve, bistable, engaging with foot guard, Connection G 1/4, Operating pressure 2.5 - 10 bar, Temp. -10 °C to 60 °C
Foot-operated valves, 3/2- and 5/2-way types, bistable or monostable (non-latching).

Service unit 3-part »Standard«, PC container, protective cage, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.5-10 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure,
with self-relieving design, centrifugal separator and proportional lubricator.

Pneumatic logic elements, OR, Techno-polymer, DN 2.7, Temperature range -10 °C to 60 °C, Working pressure 1.5 to 8 bar
Pneumatic logic elements are available with five different functions: OR, AND, NOT, YES, MEMORY.
All elements have an adapter for the Ω-rail (DIN EN 50022) integral with the body.

Reducing fitting, Sealing cone, Nut M18x1.5 i., Pipe exterior Ø1 12 mm, Pipe exterior Ø2 8 mm, PN max. 315 bar, Stainless steel
Version with parallel thread and soft seal made of NBR.

Standard pressure gauge »pressure line« Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0-4 bar/60 psi, Ø 63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in L-fitting »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Filter insert 5 µm, sintered bronze, for filter for high pressures up to 60 bar, G 3/8 and G 1/2

Reducing nipple, long type, G 1/4 o., G 3/8 i., AF 19, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Locknut DIN 981 KM3 M17x1 zinc plated
Material: Steel zinc-plated, Strength min. 350 N/mm2.These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65388637

Ferrite 18 N
PM-TB-F-SG-D16x4.5x11.5xM3
SKU: GM16503
Stock: 1
Diameter (D): 16 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Slide rail DZ 9301 slide length 711mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Plastic. Balls: Hardened steel. Sold by piece (1 x product no. = 1 single slide). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Lengths to 1.5 meters. Optional clip-on bracket accessory kits type 634 available. Service life 10,000 cycles ( to 217 kg up to 75,000 cycles). Temperature range: -20°C to +70°C. Note Recommended fastening: M5 / M6 screw. Screw head diameter max. 12.7 mm. Screw head height max. 4.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64905128

timing bar XL 1/5" (5.08mm) 48 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A. Profile XL = 1/5" = 5.08 mm.
Article ID: 18094800

Round cylinder »MI«, double-acting, Magnet, Piston Ø 32, Stroke 100, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Line pressure regulator 200 bar, incl. pressure gauge, G 1/4 i., Control range 1 - 50 bar, Operating temperature -10 °C to 90 °C
Inline pressure regulator for up to 200 bar input pressure; suitable for compressed air, nitrogen and other neutral, compressed gases.

3/2-way miniature valve, Mechanical, Tappet panel mounting, NC, M5 (side), Operating pre. 0.5-10 bar, Operating temp.-10°C to 60°C
Miniature valves, 3/2-way type, NC or NO.