Pipe double nipple, R 1, Length 60 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Reducing piece POM, Supports 6 mm, for hose exterior Ø 4 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Chain tensioner SPANN-BOX® size 1 long high tensioning force 08 B-2 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040725

Samarium-Cobalt (SmCo) 11 N
PM-TB-S-SG-D8x4.5x11.5xM3
SKU: GM17202
Stock: 59
Diameter (D): 8 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Lifting eye nut DIN 582 M12 steel C15E self coloured ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458612

Bevel gear made of steel module 3 45 teeth i=2.5:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).With crowned, milled teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36146900

Mist oiler »Standard«, PC container, protective cage, Size 3, G 1/2, Input pressure max. 16 bar, Medium / ambient temp. max. 60 °C
Proportional lubricators, oil can be filled under pressure.

Precision pressure regulator without pressure gauge, G 1/2, Control range 0.05 - 3 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range -1 / 0 bar, Ø50
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector R 1 1/2 o., for hose I.D. 38 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Quick-connect coupling I.D. 5, bright brass, rigid, Hose connection 8x6, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
One-hand quick disconnect couplings, one side sealing, compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology.

Straight push-in connector, reducing, for hose exterior Ø 4 mm, plug nipple Ø 6 mm, max. 10 bar, »Blue Series« mini
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Adjustable L-fitting, Sealing cone, 360° rotating, Nut M16x1.5 i., Pipe exterior Ø 10 mm, PN max. 315 bar, galvanised steel

Angled piece, exterior / exterior, R 1/8, AF 10, Operating pressure max. 60 bar, Operating temperature max. 150 °C, Bright brass

Chain tensioner SPANN-BOX® size 1 long high tensioning force 10 B-2 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040726

Spur gear made of stainless steel 1.4305 with hub module 3 45 teeth tooth width 25mm outside diameter 141mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.


Article ID: 23399045

Samarium-Cobalt (SmCo) 20 N
PM-TB-S-SG-D10x4.5x11.5xM3
SKU: GM17203
Stock: 14
Diameter (D): 10 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Pillow block bearing unit BF 40 bore 40mm material steel black oxide finished
Material: Housing from steel, all surfaces machined, black oxide finished. On request: nickel-plated. With quality rolling bearing from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the support side. With one movable single row deep groove ball bearing with shields (2Z). With 6 mounting holes. Retaining ring for fixing on the spindle end is included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for fixed side: Pillow Block Bearing BK. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64200240

timing bar AT10 25 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16892500

Safety ball valve lockable, Venting hole G 1/4, nickel-plated brass, Operating temp. max. 100 °C, Rp 1 1/4, DN 32, PN max. 14 bar
Safety ball valves, two parts, made of nickel-plated brass.
Specially designed for pneumatic applications.
The valve shuts off the supply line and bleds the application area.
Lockable hand lever in closed position ensures a high protection against manipulation.

Precision pressure regulator without pressure gauge, G 1/2, Control range 0.05 - 7 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0-1.6 bar, Ø 50
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector R 1 1/2 o., for hose I.D. 50 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Standard pressure gauge »pressure line« Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0-6 bar/90 psi, Ø 63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in L-connector, Plug nipple 6 mm »Blue Series« mini, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Filter element 20 µm, for service unit »ONE«

Angled piece, exterior / exterior, R 1/8, AF 10, Operating pressure max. 60 bar, Operating temp. max. 150 °C, nickel-plated brass

Chain tensioner SPANN-BOX® size 1 long high tensioning force 12 B-2 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040727

Samarium-Cobalt (SmCo) 40 N
PM-TB-S-SG-D13x4.5x11.5xM3
SKU: GM17204
Stock: 7
Diameter (D): 13 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Pillow block bearing unit BF 40 bore 40mm material steel nickel plated
Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearing from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the support side. With one movable single row deep groove ball bearing with shields (2Z). With 6 mounting holes. Retaining ring for fixing on the spindle end is included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for fixed side: Pillow Block Bearing BK. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201240

timing bar HTD 3M 72 teeth length 200mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 17097200

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 32, Stroke 75, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Precision pressure regulator without pressure gauge, G 1/2, Control range 0.05 - 5 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Reducing sleeve, round, G 1 1/2 i., G 1 1/4 i., Working pressure max. 20 bar, Stainless steel 1.4408

L-ring piece, G 1/8, for hose exterior Ø 8 mm, Working pressure max. 15 bar, Stainless steel 1.4404
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

Standard pressure gauge »pressure line« Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0-16 bar/235 psi, Ø63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Angle connector POM, for hose exterior Ø 10 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Push-in L-fitting »metallica«, rotating, R 3/8 o., for hose exterior Ø 14 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight screw-in fitting, FKM O-ring, G 1/8 o., for hose 8/6 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Chain tensioner SPANN-BOX® size 1 long high tensioning force 16 B-2 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040728

Samarium-Cobalt (SmCo) 60 N
PM-TB-S-SG-D16x4.5x11.5xM3
SKU: GM17205
Stock: 70
Diameter (D): 16 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Ball flange bearing SSUCF 210 bore 50mm housing and bearing stainless steel
Material: Housing: Stainless steel 1.4305 (X5CrNi18-10, AISI 304). Rolling bearing: Stainless steel 1.4125 (X105CrMo17, AISI 440 C), lubricated with grease FM 222 for food processing machinery, with registration FDA, CIFA, KPF2K-20, NSF H1. Temperature range: -20°C to +90°C (for short time up to +120°C).With 4 mounting holes.The rolling bearing can be swiveled when mounting to compensate shaft misalignement.The shaft will get fastened with 2 setscrews. Lubricated for life at normal operating conditions. Re-lubricating is possible.Delivery with stainless steel grease nipple.
Article ID: 62699050

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 20, Stroke 400, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Precision pressure regulator without pressure gauge, G 1/4, Control range 0.05 - 7 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Reducing sleeve, round, G 1 1/2 i., G 1 i., Working pressure max. 20 bar, Stainless steel 1.4408

T screw-in fitting, R 1/4 o., Pipe exterior Ø 6 mm, PN max. 315 bar, Stainless steel 1.4571

Standard pressure gauge »pressure line« Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0-2.5 bar/36 psi, Ø 63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, G 1/8 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Push-in T-fitting »click-clock«, rotating, G 1/2 o., for hose exterior Ø 14 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Double threaded nipple »value line«, G 3/8, G 1/2, AF 24, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

Chain tensioner SPANN-BOX® size 1 long high tensioning force 06 B-3 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040731

Sprocket KRR with hub 08 B-1 1/2x5/16" 35 teeth material stainless steel 1.4305
Material: Stainless steel 1.4305.

Teeth milled, pre-bored.

General dimensions:
B1 = 7,2 mm, c = 1,3 mm, r3 = 13 mm. Other dimensions: See the table.


Article ID: 10599135

Samarium-Cobalt (SmCo) 90 N
PM-TB-S-SG-D20x6x13xM4
SKU: GM17206
Stock: 2
Diameter (D): 20 mm
Height (H): 6 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Slide set DZ 5417 slide length 350mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in the closed position. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 049 30, Slides 5417
Article ID: 64904935

Protective earmuffs, Noise level range to 105 dB, SNR value 31 dB, Weight 210 g
For very high noise levels and effective protection at central and high frequency noise.

Wide, soft padded headband distributes the weight efficientlyTwo-point suspension exerts low pressure for comfortable, long term useSoft, liquid foam-filled ear cushions provide added comfort

Precision pressure regulator without pressure gauge, G 3/8, Control range 0.05 - 7 bar, Input pressure max. 16 bar
With high flow rate and large secondary venting.

Diaphragm pressure regulators with large secondary venting for applications requiring an extremely accurate working pressure, especially at high flow rates.

Bushing - blocking valve, Brass, Medium temperature max. 90 °C, G 1/2, DN 15, PN max. 10 bar

Metal container incl. viewing tube, for mist oiler and active charcoal filter »variobloc«, Size 1, G 1/4 and G 3/8

Standard pressure gauge »pressure line« Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0-10 bar/145 psi, Ø 63
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, R 1/8 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C