Fixing clip D=36mm spring band steel
Material Standard: Spring band steel. Material Stainless: Stainless steel. Matching to ball transfer units with flange and the same housing diameter D like the fixing clip. By using these clips, the fitting height increases 0.3 mm. 1) Seating bore.
Article ID: 65439136

Hexagonal trapezoidal nut steel C35Pb Tr.60 x 9 single-start left length 90mm wrench size 90mm
Material: Steel C35Pb. Tolerance zone 7H. Height = 1,5 x diameter. Attention: Steel nuts get very easily thightened on a spindle made from Steel or stainless steel. This nuts are only for clamping, manual adjustments or as fastening nut. Not suitable for drive systems.

Article ID: 64366000

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range -1/+0.6 bar, Ø 63
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Valve replacement set, for pressure regulator »Saxonia« for potable water, R 1 1/4

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 100, Stroke 10, G 3/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Metered air gun 90 mm pipe, POM, Connection thread Rc 1/4, Temperature range -20 °C to 60 °C, PN max. 16 bar, Sleeve I.D. 9
With noise-reducing Star-Tip nozzle.
Ergonomic grip with a very high blowing force. Several possible hanging points thanks to the modified handle. Robust yet lightweight for a long service life. With its ergonomic design, the gun can be used by both left and right-handed users!

Straight push-in bulkhead connector, M12x1, for hose exterior Ø 4 mm, Working pressure max. 15 bar, Stainless steel 1.4404
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

Reducer, Pipe exterior Ø Female connector 22/8 mm, PN max. 160 bar, a/f1 24, a/f2 17, a/f3 36, galvanised steel
Reducer, light type

Screw-in support POM, G 1/2, for hose exterior Ø 15 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Throttle check valve, Supply air throttle (»V«) push-in connector hose 6, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.

Closing cap »Blue Series«, for hose exterior Ø 6 mm, Working pressure max. 10 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Chain tensioner SPANN-BOX® size 1 short high tensioning force 12 B-3 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040537

Clamp collar single-split steel C45 black oxide finished bore 100mm with bolt DIN 912 12.9
Material: Steel C45, black oxide finish. Screw steel 12.9.Features:
does not damage the shaft, stronger clamping force than with set
collars, even distribution of clamping forces, easy readjustment,
precision honed bores. The threads of the screws DIN 912 are covered
with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range:
-40°C to +175°C.Remarks to collars from steel:The
black oxide on the clamping collars is formulated as part of the total
performance of the product. It enhances the holding ability of the
collar, it efficiently reduces slipping on the shaft, has
anti-stick-slip characteristics and helps to keep the torque rating of
the screw within its designed parameters. The oxide layer also provides
corrosion protection.

Article ID: 62320000

Neodymium (NdFeB) 5 N
PM-TB-N-SG-D6x11.5xM3
SKU: GM17600
Stock: 10
Diameter (D): 6 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

timing bar T10 32 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16493200

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 4 bar, Ø 63
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ125,Stroke120,G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 1 bar, Ø 50
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Soft PVC workshop hose set, Safety coupling, Temperature max. 60 °C, Hose Ø 14.5x9, PN at 20 °C max. 12 bar, Length 5 m
Highly flexible hose for compressed air applications in workshop areas. Assembled with brass stem and brass quick disconnect coupling DN 7.2 optional with pushbutton safety coupling DN 7.4 and galvanised steel stem.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Push-in L-fitting »Blue Series«, Self-locking, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Bushing, round, Short design, G 1/2, Working pressure max. 20 bar, Stainless steel 1.4408

Plug-in connector for pushbutton safety couplings I.D.11, ISO 6150 C, Stainless steel, Sleeve I.D. 13, max. 16 bar, -20°C to 200°C

Reducing nipple, long type, G 3/8 o., G 1/4 i., AF 19, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Replacement sieve, for pressure regulator »Saxonia« for potable water, R 1 1/4

Chain tensioner SPANN-BOX® size 1 long high tensioning force up to 06 B-1 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040701

Feather key DIN 6885 version A 5 x 5 x 30 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899103

Bevel gear made of steel module 5 20 teeth i=2:1 milled
Material: up to product no. 36105700: 11SMnPb30. From product no. 36106000: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36216000

Neodymium (NdFeB) 13 N
PM-TB-N-SG-D8x4.5x11.5xM3
SKU: GM17601
Stock: 20
Diameter (D): 8 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

V-belt pulley material aluminium profile XPA, SPA and A (13) 2 grooves nominal diameter 315mm
Material: Special Light Alloy with Cast-Iron core. V-Belt Pulleys with nominal diametre including 250 mm are supplied as solid pulley, from 280 mm Ø as spoked pulley. 1) can only be used with standard V-belt DIN 2215 . * without cast-iron hub reinforcement.

Article ID: 15223100

Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, centric, G 1/4, Meas. range 0 - 4 bar, Ø 63
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range -1 / +5 bar, Ø 63
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125,Stroke120, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0-2.5 bar, Ø 50
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Dirt strainer, nickel-plated brass, Sieve insert mesh width 0.5 mm, Operating temp. -20°C to 110°C, G 1 1/2, DN 40, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Hose sleeve, ball nipple, hose I.D. 25, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Straight push-in fitting »metallica«, R 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Plug-in connector for pushbutton safety couplings I.D.11, ISO 6150 C, Stainless steel, Sleeve I.D. 16, max. 16 bar, -20°C to 200°C

Straight screw-on fitting, »value line«, G 1/4 i., for hose 8/6 mm, AF 17, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

Chain tensioner SPANN-BOX® size 1 long high tensioning force 08 B-1 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040705

Clamp collar double-split steel C45 black oxide finished bore 100mm with bolts DIN 912 12.9
Material: Steel C45, black oxide finish. Screws steel 12.9.Features:
does not damage the shaft, stronger clamping force than with set
collars, even distribution of clamping forces, easy readjustment,
precision honed bores. The threads of the screws DIN 912 are covered
with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range:
-40°C to +175°C.Remarks to collars from steel:The
black oxide on the clamping collars is formulated as part of the total
performance of the product. It enhances the holding ability of the
collar, it efficiently reduces slipping on the shaft, has
anti-stick-slip characteristics and helps to keep the torque rating of
the screw within its designed parameters. The oxide layer also provides
corrosion protection.
Article ID: 62350000

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 8mm outer diameter 12mm length 12mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62331800

Neodymium (NdFeB) 25 N
PM-TB-N-SG-D10x4.5x11.5xM3
SKU: GM17602
Stock: 63
Diameter (D): 10 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

timing bar AT10 32 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16893200

Clamp collar single-split steel C45 zinc plated bore 100mm with screw DIN 912 12.9
Material: Steel C45 zinc-plated. Screw steel 12.9.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62388200

Cartridges, for pressure regulator for potable water, without DVGW, R 1/2, R 3/4 and R 1

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 2.5 bar, Ø 63
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.

Switch valve (3/2-way valve) »variobloc«, 24 V DC, Size 2, G 1/2, Working pressure 3 - 10 bar
For pressurising and relieving pneumatic systems. 3/2-way type including silencer.
Ideal as the main "on" valve for service units.
The pressure in the line is exhausted when the valve is switched off.

Standard pressure gauge, triangle front ring, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 6 bar, Ø 50
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Silencer, sintered damper element, stainless steel housing, adjustable,G1/2, pressure 0 to 20 bar, Operating temp. -10°C to 600°C

Straight screw-in fitting, Soft sealing, G 3/4 o., Pipe exterior Ø 22 mm, PN max. 160 bar, AF1 36, AF2 32, galvanised steel
Male connector, parallel male thread and soft seal, light type

Angled threaded connector 90°, Brass 2.0401, M8x0.75 ET tapered acc. to DIN 158, Hose connection 9 mm, Operating pres. max. 15 bar

Throttle check valve, Supply air throttle (»V«) Threaded connection G 1/4 i., G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder to restrict the incoming air.
Compact type of construction, also ideal where space is restricted.

Locking screw, Hexagonal socket 10 mm, G 1/2, NBR O-ring nickel-plated brass, Max. working pressure 25 bar,Max.operating temp.80°C
Suitable for air, water, oil, steam, etc.

Retaining ring DIN 472 55mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61765500

Chain tensioner SPANN-BOX® size 1 long high tensioning force 10 B-1 stainless steel
Material: Housing from stainless steel. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).



Article ID: 14040706

Neodymium (NdFeB) 60 N
PM-TB-N-SG-D13x4.5x11.5xM3
SKU: GM17603
Stock: 38
Diameter (D): 13 mm
Height (H): 4.5 mm
Material housing: Galvanized steel
Compact magnet systems with a steel shell and with threaded bush for easy mounting. Due to the shell of these pot magnets, the magnetic field strength increases and they are more resistant to corrosion or chemicals. Pot magnets have a single attracting surface. This precludes dispersion of the magnetic field. Pot magnets with threaded bush are available in neodymium, ferrite and samarium cobalt.

Deliverable from stock
Easy to install
Available in various qualities

Construction of NdFeb pot magnets

What does a neodymium pot magnet consist of?

These super-strong pot magnets are made of the alloy neodymium-iron-boron (NdFeB), which Goudsmit markets under the brand name Neoflux®. The shell - or pot - provides magnetic shielding. Goudsmit supplies neodymium pot magnets with a brass or steel shell. The holding surface has a protective coating to prevent corrosion.

Operating temperature

When does loss of magnetic strength occur?

Neodymium cylindrical and flat pot magnets have an operating temperature of up to 80 °C. When heated to this temperature, the magnet loses 15 to 20% of its magnetic strength. This is not permanent; the force is restored when the magnet returns to the normal ambient temperature.
External magnetic fields may also cause loss of magnetic force. An air gap or non-magnetic materials located between the magnet and workpiece reduce the tensile force.

Important to know

Loss of holding force

To prevent loss of holding force due to magnetic short-circuit, neodymium magnets with a brass shell may not be pressed directly into iron. Always maintain a certain distance between the brass shell of the pot magnet and the iron. Contact Goudsmit for specific recommendations.

Spur gear made of polyketone die-cast with hub module 0.5 60 teeth tooth width 3mm outside diameter 31mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28106001

Trapeziodal-threaded spindle DIN 103 Tr.18 x 4 x 2000mm long single-start right material 1.4305 rolled
Material: 1.4305. Up to size Tr. 40 x 7 rolled, above whirled. Tolerance zone 7e. Length sawed (length may be longer than nominal length), edges not broken.
Article ID: 64099218

Clamp collar double-split steel C45 zinc-plated bore 100mm with screws DIN 912 12.9
Material: Steel C45, zinc-plated . Screws steel 12.9.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62388500

Glycerine pressure gauge CrNi steel design, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range -1 / +9 bar, Ø 63
Glycerine-filled bourdon-tube pressure gauge, CrNi steel type.

For use in the chemical/petrochemical process industry, power stations, machinery and industrial plant engineering.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid, corrosive and crystallising media which do not have high viscosity, also in corrosive atmosphere.