timing bar MXL 0.080" (2.03mm) 72 teeth length 160mm material aluminium
Material: Aluminium ähnlich EN AW2017A.Profile MXL = 0,08" = 2.032 mm.
Article ID: 18197200

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125, Stroke50, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Tempered coupling DN 9, Exterior thread, Blocking valve, Brass, M16x1.5 straight, Operating pressure max. 15 bar
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Active charcoal element, Active charcoal-POM, Body made of aluminium, for active charcoal filter »multifix«, Size 3, G 1/2

3/2-way blocking valve »G«, Mounting bracket, Padlock and silencer, Manually actuated, Size 300, G 1/4, Input pressure 0 - 9 bar
Rotary switch can be turned 90°, lockable.
The valve is used to switch off the air supply and is normally installed upstream of a pressure regulator, filter regulator or service unit.
When the valve is closed, the residual air on the P2 side is discharged into the atmosphere through the relief port on the bottom.

Male branch elbow »universal short«, long, rot. 1/8, hose-Ø 8, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Pivoting head fastening, »TC« type for round cylinder »MI« and »MSI«, for piston Ø 8-10
Hinge head model, »TC« type

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 0.6 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector, O-ring »value line«, G 3/8, for hose I.D. 12, Operating pressure max. 60 bar, Operating temp. max. 80°C
For air, water, steam, oil, etc.

Gear rack made of stainless steel module 3.18 (metrical pitch 10mm) tooth width 30mm height 30mm length 2000mm
Material: Stainless steel 1.4305. Milled teeth. Precisely
Straightened. Straight teeth. Pressure angle 20°. Tooth quality 8d25
modelled on DIN 3962, 3967, 3968. Pitch 5 mm = Module 1.59. Pitch 10 mm
= Module 3.18. The teeth on the gear racks are manufactured using an
overhead milling cutter. This leads to negative tolerances for dimension
a and h0: At pitch 5mm: -0,2 mm. At pitch 10mm: -0,3 mm. From Module 2,
except for nominal length 500 mm, cut for continuous linking. * Length =
Nominal length. The real length is roughly one multiple of the pitch.

Article ID: 21099609

Loctite 2400, Middle Strength Thread Locking, Content 50 ml ================================================= Actual safety data sheet from 01.06.2015 on the internet in the section Downloads =================================================
Specifications
“White” material safety data sheet without hazard symbols.

Thread size: to M36.

Strength: Medium.

High chemical resistance.

Functional strength (Typical value at 22°C): 2 hours.

Breakaway torque tested according to ISO 10964: 20 Nm.

Long-term temperature resistance: -55°C to +150°C.
Approvals
WRAS (BS 6920): 1104507.

Medium threadlocker formulated to secure and seal bolts, nuts and studs
to prevent loosening due to vibration. It works on all metals and
passive substrates. Slight contamination by industrial oils, corrosion
prevention oils and cutting fluids is tolerated. Its key differentiator
is the “White” Material Safety Data Sheet. LOCTITE 2400 carries no
hazard symbols, risk or safety phrases and does not contain any
declarable carcinogens, mutagens or reproductive toxins. ApplicationsAll threaded connections which require
high durability against strong vibrations and shocks.

Article ID: 14073115

Magnet dimensions : 380x204x55 mm
SCH-M-N-204x55-0400-B-B-B
SKU: E0014217
Stock *: 0
Width: 538 mm
Height: 520 mm
Weight: 50 kg
Chute magnets are neodymium plate magnets with a hinged extractor plate and a mounting construction for self-mounting the systeem against the wall of your product channel.They are used for removal of ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes up to 45°.

With neodymium plate magnets
Max. holding field 180 mm
Capture Fe particles from 0.5 mm
Quick cleaning through use of extractor plates
Max. chute angle 45°

Application

Free-fall and chute transport

Chute magnets are mainly used for removing ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes with a sliding angle of max. 45˚.
 
Chute magnets are a simple solution for removing iron contamination. You can easily install them yourself, and they deliver a high separation efficiency. We default use neodymium magnetic plates, because they are extremely powerful, compact and lightweight.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Chute magnets have robust neodymium magnetic plates that are placed behind a stainless steel extractor plate. 2 quick-release fasteners clamp the magnet with extractor plate against the pipe channel.
 
Summary of important specifications

Materials system and magnet casing: stainless steel
Finish: grit blasted,
Material seals: EPDM, FDA-approved


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Filtering & discharging of ferrous contaminants

You can clean the chute magnet through use of the hinged extractor plate for quick-cleaning. When you swing the hinged extractor plate away from the magnet, the ferrous particles will fall off of the extractor plate as soon as they are far enough away from the magnet.
 
For reasons of safety, the operator must operate the chute magnets with two hands. The magnets are secured in the outermost cleaning position, after which the operator has both hands free for cleaning.

conical seat DIN6319 PTFE-coated inner-Ø 14,2mm outer-Ø 24mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65598512

Track for linear guide DFG 115 aluminium length 1500mm
Material: Track and carriage from aluminium, hard anodised. Plain bearings from advanced technical polymer.Linear guide for universal use.Video clip (2.5 minutes) for illustrating All parts have to be ordered seperately. Dimensionally interchangeable with rolling bearing linear motion guides ISO 12090 size 15. Three types of carriages on choice: non-adjustable / manual adjustable / automatic adjustment. Four track lenghts on choice (for to cut by the customer). Several carriages can be used on one track. Resistant against corrosion, suitable for high pressure wash down. Long service life, maintenance-free. Temperature range: -40°C to +90°C. Note: Two or more tracks can be butted together to create a longer track. Misaligned tracks will cause excessive wear on the guides. Please see catalog page (PDF).
Article ID: 64970715

Glycerine pressure gauge with metal housing, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0-1000 bar, Ø 100
Glycerine-filled bourdon-tube pressure gauge.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

L-multi-distributor »Blue Series«, 3-fold, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Short stroke cylinder, double-acting, Magnet, Piston Ø 32, Stroke 10, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Suspension chain 3 m

Male branch tee »universal short«, rotating, 1/8, hose-Ø 6, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Push-in L-connector, Plug nipple 6 mm »Blue Series«, reducing, for hose exterior Ø 4 mm, Working pressure max. 15 bar, Plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 4 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in hose connector, G 1/2 o., for hose I.D. 16, nickel-plated brass
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2.5 45 teeth tooth width 25mm outside diameter 117.5mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23295045

Internal gear made of 1.4305 (AISI303) module 1,0 25 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499425

Timing belt pulley AT10 material aluminium 72 teeth for belt width 32 mm 47 AT10/72-0
Material: Aluminium similar EN AW2017A. Flanges zinc-plated steel.
Article ID: 16847200

Loctite 2700, High Strength Thread Locking, Content 5 ml ================================================= Actual safety data sheet from 30.11.2016 on the internet in the section Downloads =================================================
Specifications
“White” material safety data sheet without hazard symbols.

Thread size: To M20.

Strength: High.

Functional strength (Typical value at 22°C): 3 hours.

Breakaway torque tested according to ISO 10964: 20 Nm.

Long-term temperature resistance: -55°C to +150°C.
Approvals
WRAS (BS 6920): 1104508.

High-strength threadlocker for maximum efficacy in the securing and
sealing of bolts, nuts and studs to prevent loosening due to vibration.
The product serves to permanently lock assemblies which must not come
loose. It works on all metals, including passive substrates . Slight
contamination is tolerated. Its key differentiator is the “White” Material
Safety Data Sheet. LOCTITE 2700 carries no hazard symbols, risk or safety
phrases and does not contain any declarable carcinogens, mutagens or
reproductive toxins.ApplicationsAll threaded
connections which require high durability against strong vibrations and
shocks.



Article ID: 14073116

Magnet dimensions : 430x204x55 mm
SCH-M-N-204x55-0450-B-B-B
SKU: E0015446
Stock *: 0
Width: 590 mm
Height: 520 mm
Weight: 54 kg
Chute magnets are neodymium plate magnets with a hinged extractor plate and a mounting construction for self-mounting the systeem against the wall of your product channel.They are used for removal of ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes up to 45°.

With neodymium plate magnets
Max. holding field 180 mm
Capture Fe particles from 0.5 mm
Quick cleaning through use of extractor plates
Max. chute angle 45°

Application

Free-fall and chute transport

Chute magnets are mainly used for removing ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes with a sliding angle of max. 45˚.
 
Chute magnets are a simple solution for removing iron contamination. You can easily install them yourself, and they deliver a high separation efficiency. We default use neodymium magnetic plates, because they are extremely powerful, compact and lightweight.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Chute magnets have robust neodymium magnetic plates that are placed behind a stainless steel extractor plate. 2 quick-release fasteners clamp the magnet with extractor plate against the pipe channel.
 
Summary of important specifications

Materials system and magnet casing: stainless steel
Finish: grit blasted,
Material seals: EPDM, FDA-approved


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Filtering & discharging of ferrous contaminants

You can clean the chute magnet through use of the hinged extractor plate for quick-cleaning. When you swing the hinged extractor plate away from the magnet, the ferrous particles will fall off of the extractor plate as soon as they are far enough away from the magnet.
 
For reasons of safety, the operator must operate the chute magnets with two hands. The magnets are secured in the outermost cleaning position, after which the operator has both hands free for cleaning.

Star knob similar to DIN 6335 made from plastic type K diameter 32mm
Material: Plastic PF31, black, glossy finish Type K = with press-fitted threaded bush made from brass.

Article ID: 66053200

Spur gear shaft made from steel with one-sided hub module 2 16 teeth toothed length 200mm total length 250mm outside diameter 36mm
Material: C45. With one-sided hub, milled, straight teeth. Pressure angle 20°.
Article ID: 24151600

Locknut UW with integrated threadlocker thread M95x2
Material: Body of the nut: steel, min. strength 350N/mm2. Locking insert: Stainless Steel. With these slot nuts no additional lock washers or keyways are required. No keyway or washer required for roller bearing. Designed for easy assembly. Maintenance-free construction. The bolt thread has to meet the medium quality of ISO 965. Please note: Ensure that there are at least two or three full threads behind the locking insert. This slot nut must not be used on shafts with keyway. Lubricate the nut when screwing it onto the shaft. Larger thread diameters can be supplied on request. Function: This system consists of a shaft nut and a special spring, acting as friction ring. This special spring is integrated into the upper part of the nut. Due to the lead of the thread the special spring locks itself between shaft and nut. The system is locked in any position!
Article ID: 65349500

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 80, Stroke 160, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Mini ball valve, Stainless steel 1.4401, IT/IT, Operating temperature -20 °C to 120 °C, G 1/4, DN 7, PN max. 63 bar

Push-in T-fitting, L-shape, rotating, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Dirt strainer, Red brass, Sieve insert mesh width 0.25 mm, Operating temperature -10 °C to 150 °C, G 1, DN 25, PN max. 25 bar
For liquids, gases, steam, water, mineral, fuel and hydraulic oils, fuels and other
non-corrosive media in a liquid or gaseous state.

Male branch tee »universal short«, L-shape, rotating 1/8,hose-Ø 6,taper seat,Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Straight screw-in fitting, G 3/8 o., Pipe exterior Ø 12 mm, PN max. 630 bar, A/F1 24, A/F2 22, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 40 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

O-ring for sealing containers, »FUTURA-mini«, Size 0, G 1/4

Internal gear made of 1.4305 (AISI303) module 1,0 30 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499430

Timing belt pulley AT10 material aluminium 84 teeth for belt width 32 mm 47 AT10/84-0
Material: Aluminium similar EN AW2017A. Flanges zinc-plated steel.
Article ID: 16848400

Loctite 2700, High Strength Thread Locking, Content 50 ml ================================================= Actual safety data sheet from 30.11.2016 on the internet in the section Downloads =================================================
Specifications
“White” material safety data sheet without hazard symbols.

Thread size: To M20.

Strength: High.

Functional strength (Typical value at 22°C): 3 hours.

Breakaway torque tested according to ISO 10964: 20 Nm.

Long-term temperature resistance: -55°C to +150°C.
Approvals
WRAS (BS 6920): 1104508.

High-strength threadlocker for maximum efficacy in the securing and
sealing of bolts, nuts and studs to prevent loosening due to vibration.
The product serves to permanently lock assemblies which must not come
loose. It works on all metals, including passive substrates . Slight
contamination is tolerated. Its key differentiator is the “White” Material
Safety Data Sheet. LOCTITE 2700 carries no hazard symbols, risk or safety
phrases and does not contain any declarable carcinogens, mutagens or
reproductive toxins.ApplicationsAll threaded
connections which require high durability against strong vibrations and
shocks.



Article ID: 14073117

Magnet dimensions : 480x204x55 mm
SCH-M-N-204x55-0500-B-B-B
SKU: E0014327
Stock *: 0
Width: 638 mm
Height: 520 mm
Weight: 58 kg
Chute magnets are neodymium plate magnets with a hinged extractor plate and a mounting construction for self-mounting the systeem against the wall of your product channel.They are used for removal of ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes up to 45°.

With neodymium plate magnets
Max. holding field 180 mm
Capture Fe particles from 0.5 mm
Quick cleaning through use of extractor plates
Max. chute angle 45°

Application

Free-fall and chute transport

Chute magnets are mainly used for removing ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes with a sliding angle of max. 45˚.
 
Chute magnets are a simple solution for removing iron contamination. You can easily install them yourself, and they deliver a high separation efficiency. We default use neodymium magnetic plates, because they are extremely powerful, compact and lightweight.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Chute magnets have robust neodymium magnetic plates that are placed behind a stainless steel extractor plate. 2 quick-release fasteners clamp the magnet with extractor plate against the pipe channel.
 
Summary of important specifications

Materials system and magnet casing: stainless steel
Finish: grit blasted,
Material seals: EPDM, FDA-approved


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Filtering & discharging of ferrous contaminants

You can clean the chute magnet through use of the hinged extractor plate for quick-cleaning. When you swing the hinged extractor plate away from the magnet, the ferrous particles will fall off of the extractor plate as soon as they are far enough away from the magnet.
 
For reasons of safety, the operator must operate the chute magnets with two hands. The magnets are secured in the outermost cleaning position, after which the operator has both hands free for cleaning.

Rubber-metal MGE diameter 10mm height 15mm inner thread M4
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510102

Linear bearing unit KG-3-KO ISO series 3 with self-aligning linear ball bearing with seals for shaft Ø 40mm open design
Material: Housing made from extruded aluminium with an open linear bearing of the ISO Series 3 from reliable brand in good quality. Self-aligning capability that accommodates tilting. All bearings are lubricated ready-to-install. Recommended shaft tolerance h6.
Article ID: 64674005

Spur gear made of POM black with hub module 2,5 60 teeth tooth width 25mm outside diameter 155mm
Material: POM, white / nature, milled teeth. Tooth quality 10d25 DIN 3967. Pressure angle 20°. Untoleranced dimensions in accordance with DIN ISO 2768 middle. Temperature limit: continuous 100°C, only short time 160°C. Water absorption (satiable) 0,5% Cws.
Article ID: 29711060

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 80, Stroke 250, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

L-multi-distributor »Blue Series«, 3-fold, rotating, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Professional cleaning gun, Bright brass with EPDM rubber cover, Operating temperature max. 50 °C, PN max. 24 bar, G 1/2 IT
Ideal for cleaning in industry and manual trades. The thick rubber coating provides thermal insulation for the hot or cold water flowing inside as well as impact protection. The flow rate is controllable with the adjustment screw (using a coin). The steel shackle allows the lever to be latched for extended use. Also suitable for drinking water.

Long reducer, Soft sealing, G 1 1/4 o., G 1 1/2 i., PN max. 315 bar, AF1 60, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Reducer, cone seal, Pipe exterior Ø Female connector 12/8 mm, PN max. 630 bar, a/f1 17, a/f2 19, a/f3 24, galvanised steel
Reducer, with cone seal, heavy type

Straight push-in connector reducing »click-clock«, M13x1, for hose exterior Ø 4/6 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 1 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Sintered bronze silencer, flat, G 1/4 o., AF 15, Operating pressure 0 - 8 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Internal gear made of 1.4305 (AISI303) module 1,0 36 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499436

Timing belt pulley AT10 material aluminium 96 teeth for belt width 32 mm 47 AT10/96-0
Material: Aluminium similar EN AW2017A. Flanges zinc-plated steel.
Article ID: 16849600

Double-strand sprocket ZRG with hub 06 B-2 3/8x7/32" 8 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 5,2 mm, B2 = 15,4 mm, c = 1,0 mm, r3 = 10 mm.Other
dimensions: See the table.

Article ID: 12188108

Magnet dimensions : 580x204x55 mm
SCH-M-N-204x55-0600-B-B-B
SKU: E0013215
Stock *: 0
Width: 738 mm
Height: 520 mm
Weight: 67 kg
Chute magnets are neodymium plate magnets with a hinged extractor plate and a mounting construction for self-mounting the systeem against the wall of your product channel.They are used for removal of ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes up to 45°.

With neodymium plate magnets
Max. holding field 180 mm
Capture Fe particles from 0.5 mm
Quick cleaning through use of extractor plates
Max. chute angle 45°

Application

Free-fall and chute transport

Chute magnets are mainly used for removing ferrous contaminants from powders, granulates, and even coarser raw material flows in free-fall pipes or chutes with a sliding angle of max. 45˚.
 
Chute magnets are a simple solution for removing iron contamination. You can easily install them yourself, and they deliver a high separation efficiency. We default use neodymium magnetic plates, because they are extremely powerful, compact and lightweight.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Chute magnets have robust neodymium magnetic plates that are placed behind a stainless steel extractor plate. 2 quick-release fasteners clamp the magnet with extractor plate against the pipe channel.
 
Summary of important specifications

Materials system and magnet casing: stainless steel
Finish: grit blasted,
Material seals: EPDM, FDA-approved


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Filtering & discharging of ferrous contaminants

You can clean the chute magnet through use of the hinged extractor plate for quick-cleaning. When you swing the hinged extractor plate away from the magnet, the ferrous particles will fall off of the extractor plate as soon as they are far enough away from the magnet.
 
For reasons of safety, the operator must operate the chute magnets with two hands. The magnets are secured in the outermost cleaning position, after which the operator has both hands free for cleaning.

Rubber-metal MGE diameter 15mm height 10mm inner thread M4
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510151

Spur gear made of plastic PA12G with steel core module 2 60 teeth tooth width 20mm outside diameter 124mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 23155060

Spur gear made of plastic PA12G with steel core module 1.5 70 teeth tooth width 17mm outside diameter 108mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 21855070