Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 80, Stroke 160, G 3/8, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure gauge pushbutton valve, G 1/2, Pressure max. 25 bar / max. 4 bar (DVGW approval), made of nickel-plated brass
For measuring local pressure.

The pressure is only measured when the piston is actuated. The measuring system is disconnected again automatically as soon as the piston is released.
In the normal position, no pressure is applied to the pressure gauge.

T-hose fitting, for hose 6/8 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 8, Stroke 30, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Push-in T-fitting »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in connector »click-clock«, M15x1, for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 2.5, Measurement range 0 - 1.6 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Replacement seal made of NBR, for Kamlok couplings made of stainless steel, for coupling DN 40 (1 1/2")

Internal gear made of 1.4305 (AISI303) module 1,0 40 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499440

Double-strand sprocket ZRG with hub 06 B-2 3/8x7/32" 9 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 5,2 mm, B2 = 15,4 mm, c = 1,0 mm, r3 = 10 mm.Other
dimensions: See the table.

Article ID: 12188109

Product inlet/outlet size : #200 mm
SBP-2020-N-F1E-B-B
SKU: SBPN202000
Stock: 1
Max. capacity: 75 m³/h
No of magnets: 2
Weight: 78 kg
For filtering ferrous contaminants from coarse, free-falling, high-capacity pipelines.The magnet plates are placed outside the product channel to secure an unobstructed product flow.Cleaning is quick and easy, by means of a hinged extractor plate (quick-cleaning).

Quick cleaning through use of extractor plates
Capacity up to 200 m³/h
With neodymium or ferrite plate magnets
Installation height 400 to 760 mm
Capture Fe particles from 0.5 mm

Application

Free-fall pipes for powders & granulates

External pole magnets filter ferromagnetic (Fe) impurities – such as iron and steel – from 0.5 to 50 mm out of powders and granulates in free-fall lines. They are used in the bulk, animal feed, plastics, ceramic and recycling industries, among others.
 
External pole magnets are very robust and are able to process high capacities. The magnets are located outside the product channel, so the product can fall through freely.
 
If fine ferrous particles must be separated from powder flows, we recommend our Cleanflow magnets.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Two magnetic plates are located opposite each other, outside the product chute. They have a deeply reaching, powerful holding field, which is strengthened through clever construction of the magnets. This enables them to 'capture' Fe particles from the product stream.
 
The magnets are fitted with hinged extractor plates for quick and easy cleaning. The magnets attract the ferrous contaminants, and clamp them against the extractor plate. Ridges on the extractor plate provide extra 'shelter' and extra clamping force for the captured ferrous parts. As a result, the product flow cannot "drag them along" again.
 
Summary of important specifications

Magnet quality ferrite or neodymium
Materials housing and materials in contact with product: stainless steel
Finishing: grit blasted / magnets painted
Material gaskets neodymium version: Silicone acc. EC1935 / FDA
Material gaskets ferrite version: sponge rubber / silicone


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.
 
Options

Magnet quality: ferrite or neodymium
Basic type: standard execution, grit blasted

Round or square in-/outlet
Food/pharma type: hygienic execution, polished

Only square in-/outlet


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The 2 magnetic plates are placed on the outside of the product channel. Therefore a guide profile is placed in the center of the inlet flange, to force the product flow towards the magnets. The product contaminated with ferrous particles passes the magnets while flowing through the separator.
The magnets attract the ferrous particles, which are then held against the extractor plate. Ridges on the extractor plates provide extra 'shelter' and extra clamping force for the captured ferrous particles, so that the product flow cannot 'drag' them along again.
 
How does the cleaning / iron discharging work?
For these quick-cleaning type external pole magnets, you need to interrupt the product flow in order to be able to clean the magnets.
 
Swing the magnets with extractor plates completely outwards. Then turn the hinged extractor plates away from the magnets. As soon as the captured ferrous particles are out of the magnetic field reach, they will automatically fall off.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the quick-release clamps
Swing the complete magnet unit as far away from the housing as possible
Swing the extractor plate away from the magnet
The ferrous particles now fall from the extractor plates; collect and dispose of them
Clean all parts with a soft, clean cloth and - if necessary - a suitable cleaning liquid
Swing the extractor plate back against the magnet
Swing the complete magnet unit back against the housing
Retighten the quick-release clamps
Restart the product flow

Rubber-metal MGE diameter 15mm height 15mm inner thread M4
Material: Elastomer: Natural rubber, hardness 55º Shore. Metal parts: Steel, zinc plated. One side with internal thread. Standard components for elastic mounting. The grade of rubber used has perfect physical properties. Temperature resistant up to 80ºC. Other sizes, Shore hardnesses or elastomer types on request.
Article ID: 68510152

Angle seat valve, Piston drive without NAMUR interface, Bronze, Medium temp. -10°C to 180°C, G 1, Pressure difference max 11 bar
Angle-seat valves with external pilot control and a self-aligning valve disc for neutral (bronze body) or corrosive (stainless steel body) media.
Very high flow due to angled seat designWater hammer prevented by fluid entry under the discSuitable for vacuum operation (low vacuum)

Distributor with 2 quick-connect couplings I.D. 7.2, »R26EMS«, Bright brass, G 1/2 IT, Operating pressure 0 - 35 bar
2-way distributor pieces made of brass with a bare metal surface, pre-assembled with quick disconnect coupling DN 7.2.
Available with threaded connection inside or outside.

Low noise flat nozzle, 1/2 - 27 UNS, Safety nozzle for high performance air gun, nickel-plated brass, Nozzle width 21 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 10, Stroke 10, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Push-in T-fitting »Blue Series«, rotating, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Angled pivot fitting »value line« rotating, G 1/8 o., for hose exterior Ø 4 mm, Operating pressure max 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 10 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Flat seal, (NBR with aramid fibres), for connection size (inch) 1 1/4, Operating temperature -20 °C to 200 °C
Maximum temperature and maximum operating pressure should not occur at the same time!

Round gear rack made of stainless steel 1.4305 module 1.5 diameter 15mm h9 length 1000mm
Material: Stainless steel 1.4305.
Outside diameter = h9 drawn.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
up to Module 2: -0,2 mm.
Module 2,5 - 4: -0,3 mm.


Article ID: 22899632

Internal gear made of 1.4305 (AISI303) module 1,0 45 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499445

Locking assembly BAR bore 48mm
Material: Steel.

For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft. For
medium torques. Self-centering. Slight axial offset possible during
assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub
12.5µm.

Article ID: 61544800

Double-strand sprocket ZRG with hub 06 B-2 3/8x7/32" 10 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 5,2 mm, B2 = 15,4 mm, c = 1,0 mm, r3 = 10 mm.Other
dimensions: See the table.

Article ID: 12188110

Product inlet/outlet size : #250 mm
SBP-2525-N-F1E-B-B
SKU: SBPN252500
Stock *: 0
Max. capacity: 100 m³/h
No of magnets: 2
Weight: 90 kg
For filtering ferrous contaminants from coarse, free-falling, high-capacity pipelines.The magnet plates are placed outside the product channel to secure an unobstructed product flow.Cleaning is quick and easy, by means of a hinged extractor plate (quick-cleaning).

Quick cleaning through use of extractor plates
Capacity up to 200 m³/h
With neodymium or ferrite plate magnets
Installation height 400 to 760 mm
Capture Fe particles from 0.5 mm

Application

Free-fall pipes for powders & granulates

External pole magnets filter ferromagnetic (Fe) impurities – such as iron and steel – from 0.5 to 50 mm out of powders and granulates in free-fall lines. They are used in the bulk, animal feed, plastics, ceramic and recycling industries, among others.
 
External pole magnets are very robust and are able to process high capacities. The magnets are located outside the product channel, so the product can fall through freely.
 
If fine ferrous particles must be separated from powder flows, we recommend our Cleanflow magnets.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Two magnetic plates are located opposite each other, outside the product chute. They have a deeply reaching, powerful holding field, which is strengthened through clever construction of the magnets. This enables them to 'capture' Fe particles from the product stream.
 
The magnets are fitted with hinged extractor plates for quick and easy cleaning. The magnets attract the ferrous contaminants, and clamp them against the extractor plate. Ridges on the extractor plate provide extra 'shelter' and extra clamping force for the captured ferrous parts. As a result, the product flow cannot "drag them along" again.
 
Summary of important specifications

Magnet quality ferrite or neodymium
Materials housing and materials in contact with product: stainless steel
Finishing: grit blasted / magnets painted
Material gaskets neodymium version: Silicone acc. EC1935 / FDA
Material gaskets ferrite version: sponge rubber / silicone


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.
 
Options

Magnet quality: ferrite or neodymium
Basic type: standard execution, grit blasted

Round or square in-/outlet
Food/pharma type: hygienic execution, polished

Only square in-/outlet


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The 2 magnetic plates are placed on the outside of the product channel. Therefore a guide profile is placed in the center of the inlet flange, to force the product flow towards the magnets. The product contaminated with ferrous particles passes the magnets while flowing through the separator.
The magnets attract the ferrous particles, which are then held against the extractor plate. Ridges on the extractor plates provide extra 'shelter' and extra clamping force for the captured ferrous particles, so that the product flow cannot 'drag' them along again.
 
How does the cleaning / iron discharging work?
For these quick-cleaning type external pole magnets, you need to interrupt the product flow in order to be able to clean the magnets.
 
Swing the magnets with extractor plates completely outwards. Then turn the hinged extractor plates away from the magnets. As soon as the captured ferrous particles are out of the magnetic field reach, they will automatically fall off.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the quick-release clamps
Swing the complete magnet unit as far away from the housing as possible
Swing the extractor plate away from the magnet
The ferrous particles now fall from the extractor plates; collect and dispose of them
Clean all parts with a soft, clean cloth and - if necessary - a suitable cleaning liquid
Swing the extractor plate back against the magnet
Swing the complete magnet unit back against the housing
Retighten the quick-release clamps
Restart the product flow

Linear ball bearing unit KG-1 ISO series 1 with shields for shaft diameter 40mm
Material: Housing made of extruded aluminium with a compact linear bearing of the ISO Series 1 from premium brand in top quality. Either with integral double-lip seal or with shields. Lubricated ready-to-install.Recommended shaft tolerance h6. * when mounting from the bottom side choose the next smaller screw size. A = with shields. B = with seals.

Article ID: 64654040

Dekabon tube, Tube-Ø: 10x6.2 mm, PN at 23 °C max. 28.8 bar, Temp. -40 °C to 80 °C, black, Roll of 25 m
Dekabon tubing, which combines the advantages of metal and plastic tubing.
Bending the very light tubing is possible without special tools. Good resistance against corrosion and various chemicals. The interior tube remains dry due to a film/aluminium barrier and can be laid in the ground without additional protection.
Connection is possible with push-in connectors (additional self testing) and cutting ring fittings (amplification sleeve recommended).

Areas of application:
- pneumatic measurement and control lines in very wet or moist environments
- air and gas sampling
- aggressive environments (corrosion)
- The interior surface is best suited for air

Mounting bracket with 2 screws, »multifix«, Size 4, G 3/4 and G 1

Low noise flat nozzle, M12x1.25, Safety nozzle standard design, nickel-plated brass, Length 100.0 mm, Nozzle width 21 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 8, Stroke 40, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Push-in L-fitting »Blue Series«, rotating, G 3/8 i./o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Replacement seal for Storz coupling, made of NBR, Storz size 90, Tappet distance 105 mm

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 16 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Plug nipple »Blue Series«, plug nipple 4 mm, Working pressure max. 15 bar, Plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Round gear rack made of stainless steel module 1.59 (metrical pitch 5mm) Ø 15mm h9 length 1000mm
Material: Stainless steel 1.4305.
Outside diameter = h9 drawn.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

Pitch 5 mm = module 1.59.
Pitch 10 mm = module 3.18.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
Pitch 5 mm: -0.2 mm.
Pitch 10 mm: -0.3 mm.


Article ID: 20599632

Internal gear made of 1.4305 (AISI303) module 1,0 48 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499448

Double-strand sprocket ZRG with hub 06 B-2 3/8x7/32" 11 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 5,2 mm, B2 = 15,4 mm, c = 1,0 mm, r3 = 10 mm.Other
dimensions: See the table.

Article ID: 12188111

Product inlet/outlet size : #300 mm
SBP-3030-N-F1E-B-B
SKU: SBPN303000
Stock *: 0
Max. capacity: 140 m³/h
No of magnets: 2
Weight: 104 kg
For filtering ferrous contaminants from coarse, free-falling, high-capacity pipelines.The magnet plates are placed outside the product channel to secure an unobstructed product flow.Cleaning is quick and easy, by means of a hinged extractor plate (quick-cleaning).

Quick cleaning through use of extractor plates
Capacity up to 200 m³/h
With neodymium or ferrite plate magnets
Installation height 400 to 760 mm
Capture Fe particles from 0.5 mm

Application

Free-fall pipes for powders & granulates

External pole magnets filter ferromagnetic (Fe) impurities – such as iron and steel – from 0.5 to 50 mm out of powders and granulates in free-fall lines. They are used in the bulk, animal feed, plastics, ceramic and recycling industries, among others.
 
External pole magnets are very robust and are able to process high capacities. The magnets are located outside the product channel, so the product can fall through freely.
 
If fine ferrous particles must be separated from powder flows, we recommend our Cleanflow magnets.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Two magnetic plates are located opposite each other, outside the product chute. They have a deeply reaching, powerful holding field, which is strengthened through clever construction of the magnets. This enables them to 'capture' Fe particles from the product stream.
 
The magnets are fitted with hinged extractor plates for quick and easy cleaning. The magnets attract the ferrous contaminants, and clamp them against the extractor plate. Ridges on the extractor plate provide extra 'shelter' and extra clamping force for the captured ferrous parts. As a result, the product flow cannot "drag them along" again.
 
Summary of important specifications

Magnet quality ferrite or neodymium
Materials housing and materials in contact with product: stainless steel
Finishing: grit blasted / magnets painted
Material gaskets neodymium version: Silicone acc. EC1935 / FDA
Material gaskets ferrite version: sponge rubber / silicone


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.
 
Options

Magnet quality: ferrite or neodymium
Basic type: standard execution, grit blasted

Round or square in-/outlet
Food/pharma type: hygienic execution, polished

Only square in-/outlet


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The 2 magnetic plates are placed on the outside of the product channel. Therefore a guide profile is placed in the center of the inlet flange, to force the product flow towards the magnets. The product contaminated with ferrous particles passes the magnets while flowing through the separator.
The magnets attract the ferrous particles, which are then held against the extractor plate. Ridges on the extractor plates provide extra 'shelter' and extra clamping force for the captured ferrous particles, so that the product flow cannot 'drag' them along again.
 
How does the cleaning / iron discharging work?
For these quick-cleaning type external pole magnets, you need to interrupt the product flow in order to be able to clean the magnets.
 
Swing the magnets with extractor plates completely outwards. Then turn the hinged extractor plates away from the magnets. As soon as the captured ferrous particles are out of the magnetic field reach, they will automatically fall off.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the quick-release clamps
Swing the complete magnet unit as far away from the housing as possible
Swing the extractor plate away from the magnet
The ferrous particles now fall from the extractor plates; collect and dispose of them
Clean all parts with a soft, clean cloth and - if necessary - a suitable cleaning liquid
Swing the extractor plate back against the magnet
Swing the complete magnet unit back against the housing
Retighten the quick-release clamps
Restart the product flow

Spur gear made of plastic PA12G with steel core module 1.5 90 teeth tooth width 17mm outside diameter 138mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 21855090

Linear ball bearing unit KG-1 ISO series 1 with double rubber seal for shaft diameter 40mm
Material: Housing made of extruded aluminium with a compact linear bearing of the ISO Series 1 from premium brand in top quality. Either with integral double-lip seal or with shields. Lubricated ready-to-install.Recommended shaft tolerance h6. * when mounting from the bottom side choose the next smaller screw size. A = with shields. B = with seals.

Article ID: 64664040

Compressed air and water hose NR / SBR, black, Temperature range -20 °C to 70 °C, Hose Ø 13x6, PN max. 20 bar, Roll of 50 m
Robust yet flexible hose type for high pressure loads.
The hose cover resists the temporary influence of oil and is non-abrasive and weatherproof.

Male hinge model, ISO 15552, ISO 21287, Ø50, with 4 screws
Male hinge model

Spray gun made of plastic, Coupling plug for standard coupling I.D. 7.2, PN max. 16 bar, Plastic container 1.2 l
Plastic gun with a lightweight yet robust plastic container. The gun rests in a cradle and can easily be removed or replaced. Suitable for solvents! The spray fan can be adjusted with a throttle.

Round cylinder »MSI«, single-acting, Magnet, Piston Ø 8, Stroke 50, M5x0.8, Working pressure 2 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Kamlok closing cap for quick-connect plug, DC type, Aluminium, Size 3/4, for plug Ø 32 mm, Pressure max. 16 bar, Temp. max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Angled screw-in fitting, R 1/8 o., Pipe exterior Ø 8 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 25 bar, Ø 63
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Angled screw-in supports, R 1/8 o., for hose I.D. 8 mm, AF 10, Over-pressure max. 14 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Internal gear made of 1.4305 (AISI303) module 1,0 50 teeth teeth width 10mm
Material: Stainless steel 1.4305.Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.
Article ID: 22499450

Rubber buffer GH ø 25mm height 30mm with through hole 10,5mm
Material: Natural rubber hardness 55º Shore A.

Simple, reasonably priced standard components used for elastic mounting.

The grade of rubber used has perfect physical
properties.

Article ID: 68572530

Double-strand sprocket ZRG with hub 06 B-2 3/8x7/32" 12 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 5,2 mm, B2 = 15,4 mm, c = 1,0 mm, r3 = 10 mm.Other
dimensions: See the table.

Article ID: 12188112

Product inlet/outlet size : #350 mm
SBP-3535-N-F1E-B-B
SKU: SBPN353500
Stock *: 0
Max. capacity: 190 m³/h
No of magnets: 2
Weight: 153 kg
For filtering ferrous contaminants from coarse, free-falling, high-capacity pipelines.The magnet plates are placed outside the product channel to secure an unobstructed product flow.Cleaning is quick and easy, by means of a hinged extractor plate (quick-cleaning).

Quick cleaning through use of extractor plates
Capacity up to 200 m³/h
With neodymium or ferrite plate magnets
Installation height 400 to 760 mm
Capture Fe particles from 0.5 mm

Application

Free-fall pipes for powders & granulates

External pole magnets filter ferromagnetic (Fe) impurities – such as iron and steel – from 0.5 to 50 mm out of powders and granulates in free-fall lines. They are used in the bulk, animal feed, plastics, ceramic and recycling industries, among others.
 
External pole magnets are very robust and are able to process high capacities. The magnets are located outside the product channel, so the product can fall through freely.
 
If fine ferrous particles must be separated from powder flows, we recommend our Cleanflow magnets.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Description
Two magnetic plates are located opposite each other, outside the product chute. They have a deeply reaching, powerful holding field, which is strengthened through clever construction of the magnets. This enables them to 'capture' Fe particles from the product stream.
 
The magnets are fitted with hinged extractor plates for quick and easy cleaning. The magnets attract the ferrous contaminants, and clamp them against the extractor plate. Ridges on the extractor plate provide extra 'shelter' and extra clamping force for the captured ferrous parts. As a result, the product flow cannot "drag them along" again.
 
Summary of important specifications

Magnet quality ferrite or neodymium
Materials housing and materials in contact with product: stainless steel
Finishing: grit blasted / magnets painted
Material gaskets neodymium version: Silicone acc. EC1935 / FDA
Material gaskets ferrite version: sponge rubber / silicone


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.
 
Options

Magnet quality: ferrite or neodymium
Basic type: standard execution, grit blasted

Round or square in-/outlet
Food/pharma type: hygienic execution, polished

Only square in-/outlet


Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The 2 magnetic plates are placed on the outside of the product channel. Therefore a guide profile is placed in the center of the inlet flange, to force the product flow towards the magnets. The product contaminated with ferrous particles passes the magnets while flowing through the separator.
The magnets attract the ferrous particles, which are then held against the extractor plate. Ridges on the extractor plates provide extra 'shelter' and extra clamping force for the captured ferrous particles, so that the product flow cannot 'drag' them along again.
 
How does the cleaning / iron discharging work?
For these quick-cleaning type external pole magnets, you need to interrupt the product flow in order to be able to clean the magnets.
 
Swing the magnets with extractor plates completely outwards. Then turn the hinged extractor plates away from the magnets. As soon as the captured ferrous particles are out of the magnetic field reach, they will automatically fall off.
 
Cleaning / iron discharging sequence

Stop the product flow
Loosen the quick-release clamps
Swing the complete magnet unit as far away from the housing as possible
Swing the extractor plate away from the magnet
The ferrous particles now fall from the extractor plates; collect and dispose of them
Clean all parts with a soft, clean cloth and - if necessary - a suitable cleaning liquid
Swing the extractor plate back against the magnet
Swing the complete magnet unit back against the housing
Retighten the quick-release clamps
Restart the product flow

Lifting eye bolt M6 x 13 stainless steel A2 casted
Material: Stainless steel A2 or stainless steel A4, cast, polished.Cost-effective version for many fastening applications, for example in household and garden for light tensioning.Not permitted as lifting device or in safety-relevant areas.Temperature range: -20°C to +200°C. Note: These ring bolts are not according to DIN 580. The load capacity is not like DIN. So, theses parts may only be used for light loads in responsibility of the customer, and never for safety-relevant applications. Depending on the casting company, these parts are marked with the size of thread and / or the manufacturer symbol.

Article ID: 65458306

Ball joint RW bore 25H7 with keyway DIN 6885-1 on both sides outer diameter 50mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63135000N

Precision levelling adjuster MN 686.3 50-22.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For parall surfaces. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699355

Pressure regulator »multifix«, incl. pressure gauge, Size 5, G 1, Input pressure max. 16 bar, Control range 0.5 - 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the button down.

Male hinge model, ISO 15552, ISO 21287, Ø80, with 4 screws
Male hinge model

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ63, Stroke90,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure regulator, continuous pressure supply »FUTURA-mini«, incl. compact press. gauge, Size 0, G 1/4, PE max. 12 bar, 0.1-4 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched.

Kamlok quick-connect socket with exterior thread, B type, Aluminium, R 3/4, for plug Ø 32 mm, Pressure max. 16 bar, max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.