Round cylinder »MI« ISO 6432, double-acting, Piston Ø 25, Stroke 300, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Dirt strainer, Red brass, Sieve insert mesh width 0.6 mm, Operating temperature -10 °C to 150 °C, G 1, DN 25, PN max. 25 bar
For liquids, gases, steam, water, mineral, fuel and hydraulic oils, fuels and other
non-corrosive media in a liquid or gaseous state.

Push-in L-fitting »Blue Series«, rotating, Rc 1/4 i., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Angled pivot fitting »value line«, G 1/4 o., for hose 6/4 mm, AF 17, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Adjustable L-fitting, Sealing cone, 360° rotating, Nut M14x1.5 i., Pipe exterior Ø 8 mm, PN max. 315 bar, galvanised steel

Straight screw-in fitting, ET conical, R 1/8, for hose 6/4 mm, AF 12, Working pressure max. 18 bar, nickel-plated brass

Locknut DIN 981 KM 20 thread M100x2 stainless steel 1.4618
Material: Stainless steel 1.4618 (AISI 201).These nuts are used for unsafed, quickly to loosen applications, or for a safe connection with an additional lockwasher DIN 5406 (for these lockwashers, a keyway is required on the shaft thread).Recommend tolerance for the shaft thread: 6g DIN ISO 965.
Article ID: 65399690

Spur gear made of polyacetal resin die-cast with hub module 0.7 35 teeth tooth width 6mm outside diameter 25.9mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28203500

Product inlet/outlet size : Ø500 / #500 mm
SPA-6-B-FI-OS-ST-NA-D-B
SKU: SPEE000066
Stock *: 0
Max. capacity: 350 m³/h
Electro bullet magnets have a powerful bullet-shaped electromagnetic magnet core. They are suitable for filtering medium to large ferrous contaminants from high capacity coarse free-fall bulk flows.Often used in eg. the bulk, animal feed, plastics, ceramics and recycling industries.Electro bullet magnets are automatic cleaning, which makes them suitable for automatic production processes. Because they need a valve box, their installation height is much larger than that of the permanent bullet magnets.

Electromagnet
Capture Fe particles from 0.1 mm
Automatic cleaning (discontinuous)
Overall height 950 to 2433 mm
ATEX II 1/2 D possible

Application

Filtering iron contamination out of high capacity coarse product streams

For filtering ferrous contaminants – such as iron and steel – out of granulates, fibres and coarser materials in high capacity non-pressurized pipelines.
 
Bullet magnets are used in the bulk, animal feed, plastics, ceramics and recycling industries, among others.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
Electro bullet magnets have a large, cylindrical electromagnet core, with a powerful, deeply penetrating magnetic field. The magnetic core has 3 magnetic poles on which trapped ferrous particles are held. The magnetic core can be switched on / off electrically. A valve box is mounted under the pipe magnet in order to be able to automatically discharge the falling ferrous particles.
 
Summary of important specifications

1 bullet-shaped magnet with 60° top cone
Magnet quality: 2000 gauss on magnet surface
Robust steel / stainless steel housing
Finish: painted
Incl. door sensor (open/close safety switch)
Incl. control box
Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Default versions

Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)

Options

Magnet iron saturation signaller 'Met-alert Watch dog'
Kobaflex PU protective coating


Working principle

Cleaning / disposal of caught metal contaminations

How does the magnetic filtering work?
Because the magnetic core is located in the middle of the product stream, the bullet magnet has a very high separation yield. The round shape of the housing and the magnetic core (with a 60° top cone) ensures continuous flow and good distribution of the product stream. The product then passes three powerful magnetic fields, where guide strips redirect any product near the outer walls back toward the magnetic core.
 
The magnets attract passing ferrous particles. The captured particles stick to 1 of the 3 magnet poles, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Fully automatic cleaning. After you have stopped the product flow, give the start signal for the cleaning. The magnetic core is switched off electrically during cleaning. The valve box automatically discharges the falling ferrous particles.
 
Cleaning / iron discharging sequence

Stop the product flow
Give the start signal for a cleaning cycle locally, or from your central control
a. The valve box is switched to iron discharging position
b. The magnet is switched off
c. The captured ferrous particles fall off and are discharged via the valve box
d. The valve box is switched back to production position
e. The magnet is switched on again
Restart the product flow

Spur gear made of polyketone die-cast with hub module 0.7 26 teeth tooth width 6mm outside diameter 19,6mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28202601

Assortment box zinc plated SL-circlips (snap rings)
Material: Steel, zinc plated. The assortment box is made from impact-resitant plastic of premium quality and is filled with SL-Retainers matching BEKbolts with groove/clevises/clevis joints. Contains 560 pieces. Weight 1.23 kg. Size Amount 4 100 5 100 6 100 8 100 10 40 12 40 14 40 16 40
Article ID: 61800002

Polyurethane timing belt HTD 8M width 100mm 8M-100 open length with tensile members from steel packed 2 x 50mm
Material: Thermoplastic polyurethane (TPU), white, with steel tensile member. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. Belts made of TPU can be welded to endless belts. When welded, the perm. tensile force is reduced to 50%.
Article ID: 17566800

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, blue, Roll of 100 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Non-return valve, G 1/4 o.,bite-type tube to thread, Pipe exterior Ø 8, PN max. 250, a/f1 17, a/f2 19, a/f3 19, galvanised steel

L-ring piece, G 1/2, for hose exterior Ø 12 mm, Working pressure max. 15 bar, Stainless steel 1.4404
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

Nipple for couplings I.D. 19, Bright brass, G 3/4 ET, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

Angled piece, 90°, interior / interior, G 1/2, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Closing cap (hexagonal design), G 3/4, AF 29, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Y- angled piece fitting »Blue Series«, rotating, R 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double threaded nipple, Cylindrical, G 1/4 o. left, G 1/4 o. left, Brass
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Bevel gear made of polyacetal resin die-cast module 1.5 10 teeth i=4:1 bore 5mm
Material: Polyacetal resin, die-cast. Shaft angle 90°. Bores from Module 1,5 machined. The bevel gears only run as a pair at the stated ratio. Thermoplastic materials have a far larger thermal expansion than metals. This fact must be considered with view to the crown and flank clearance when mounting the gear. Crown clearance Sk ~ 0,25 . m, flank clearance Sc ~ 0,05 . m. Thermal expansion coefficient = 1,1 . 10-4 1/°C. The bevel gears are also available with smaller bores, or with feather key groove. Additional charge worked out on time basis. Note Regarding the Gears Made of Polyacetal Resin: Inside these die-cast parts are some cavities caused by production. These parts should therefore not be drilled too deep. With larger bores or when grooving the cavities might become visible. This often does not affect the functionality. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 35578800

Ball transfer unit 388 size 38,1 total height 60,3mm housing steel with KTL "anti-oxide" electrophoretic coating
Material: Housing: Steel, with KTL “Anti-Oxide” electrophoretic coating.  Ball cup: Steel, case hardened.  Balls: Steel 100Cr6, hardened. Heavy duty ball transfer unit for high load. High shock resistance. Very low friction. Orientation: Anyway. From size 25.4 with felt seal. With drain hole. Conveying speed max. 2m/sec.Temperature range -30°C to +160°C. 1) Elliptical flange with 2 bores. 2) Not countersunk. Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.
Article ID: 65438838

Sliding hub FS torque adjustable 7-34 Nm with pilot bore 10H8 outer diameter 64mm max. bore: 22mm bush length 10.3mm
Material: Hub: Steel, zinc-plated and passivated. Spring: Steel, black. The sliding hubs can be delivered ex stock, pre-drilled with standard bush length. Required bush length: The required bush length depends on the width of the component to be joined. Up to Prod. No. 612 006 00: Bush length 4.2 mm for a component width of 5.3 to 6.0 mm. From Prod. No. 612 010 00: Bush length in mm = 1.5 x G + C. Other bush lengths and customized bores or feather-key grooves against extra charge. At sizes 120 and 180, the lock washer is a round plate, without edges.
Article ID: 61201000

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 8x6 mm, PN at 23 °C max. 10 bar, black, Roll of 100 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Non-return valve, G 1/2 o., bite-type tube to thread, Pipe exterior Ø 15, PN max. 250, a/f1 27, a/f2 27, a/f3 32, galvanised steel
Non-return valve, flow direction bite-type tube to thread, parallel male thread, light type

Polyurethane DUO hose (PUR), Temperature range -35 °C to 60 °C, Hose Ø 6x4 mm, PN at 20 °C max. 14 bar, Roller length 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to oils, greases, aliphatic hydrocarbons and oxygen.
Suitable for vacuum.

Nipple for couplings I.D. 19, Bright brass, G 1 ET, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

Angled piece, 90°, interior / exterior, G 1/2, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Push-in L-fitting »Blue Series« long, rotating, M5 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

3/3 Stand pipe fitting, G 3/4 ET x 19 mm, nut 1, taper seat, Brass with a bare metal surface

2-ear hose clamp, Steel bright galvanised (W1), Clamping range 43.0 - 46.0 mm, Belt width 10.5 mm
Quick and safe assembly: the two parts are simply pressed together.

Product inlet/outlet size : Ø250 mm
SPA-3-B-TC-FO-ST-Ex-D-B
SKU: SPAB000063
Stock *: 0
Max. capacity: 100 m³/h
Electro bullet magnets have a powerful bullet-shaped electromagnetic magnet core. They are suitable for filtering medium to large ferrous contaminants from high capacity coarse free-fall bulk flows.Often used in eg. the bulk, animal feed, plastics, ceramics and recycling industries.Electro bullet magnets are automatic cleaning, which makes them suitable for automatic production processes. Because they need a valve box, their installation height is much larger than that of the permanent bullet magnets.

Electromagnet
Capture Fe particles from 0.1 mm
Automatic cleaning (discontinuous)
Overall height 950 to 2433 mm
ATEX II 1/2 D possible

Application

Filtering iron contamination out of high capacity coarse product streams

For filtering ferrous contaminants – such as iron and steel – out of granulates, fibres and coarser materials in high capacity non-pressurized pipelines.
 
Bullet magnets are used in the bulk, animal feed, plastics, ceramics and recycling industries, among others.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
Electro bullet magnets have a large, cylindrical electromagnet core, with a powerful, deeply penetrating magnetic field. The magnetic core has 3 magnetic poles on which trapped ferrous particles are held. The magnetic core can be switched on / off electrically. A valve box is mounted under the pipe magnet in order to be able to automatically discharge the falling ferrous particles.
 
Summary of important specifications

1 bullet-shaped magnet with 60° top cone
Magnet quality: 2000 gauss on magnet surface
Robust steel / stainless steel housing
Finish: painted
Incl. door sensor (open/close safety switch)
Incl. control box
Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Default versions

Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)

Options

Magnet iron saturation signaller 'Met-alert Watch dog'
Kobaflex PU protective coating


Working principle

Cleaning / disposal of caught metal contaminations

How does the magnetic filtering work?
Because the magnetic core is located in the middle of the product stream, the bullet magnet has a very high separation yield. The round shape of the housing and the magnetic core (with a 60° top cone) ensures continuous flow and good distribution of the product stream. The product then passes three powerful magnetic fields, where guide strips redirect any product near the outer walls back toward the magnetic core.
 
The magnets attract passing ferrous particles. The captured particles stick to 1 of the 3 magnet poles, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Fully automatic cleaning. After you have stopped the product flow, give the start signal for the cleaning. The magnetic core is switched off electrically during cleaning. The valve box automatically discharges the falling ferrous particles.
 
Cleaning / iron discharging sequence

Stop the product flow
Give the start signal for a cleaning cycle locally, or from your central control
a. The valve box is switched to iron discharging position
b. The magnet is switched off
c. The captured ferrous particles fall off and are discharged via the valve box
d. The valve box is switched back to production position
e. The magnet is switched on again
Restart the product flow

Lifting eye bolt DIN 580 M10 x 17 steel C15E galvanized ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E zinc-plated.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458110

Slide set DA 5321 slide length 500mm aluminium
Material: Slide elements: Aluminium.Ball retainers and balls: Stainless steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Mounting bracket for electrical cabinets on request. Service life 40,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk/ 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. The load capacity was tested at a slide spacing of 450mm. Attention: vertical (side) mounting only.
Article ID: 64904550

Polyurethane timing belt HTD 8M width 100mm 8M-100 open length PAZ = Polyamide fabric on tooth side
Material: Thermoplastic polyurethane (TPU), white, with steel tensile member. With green polyamide fabric on the tooth side. Temperature range -30º to +80ºC. TPU PAZ belts can be welded to endless belts (tensile force -50%). The polyamide fabric reduces the friction on aluminium or steel plates to approx. 50%. On plastic sliding plates, the friction reduction is approx. 30%. So, depending on the application, the needed driving power is much lower. By the fabric, the wear resistance of the belt is much higher and the noise is lower. Application: for example supported transportation belt drives.
Article ID: 17566801

PVC hose, Transparent, Temperature -15 °C to 60 °C, Hose Ø 24x20, PN short time loading at 20 °C max. 3 bar, Roller length 50 m
Food-grade PVC hose in conformity with EU Regulation No. 10/2011.
Unbeatably flexible hose for non-pressurised conveying of a wide variety of liquids such as fruit juices, mineral water, alcoholic beverages (up to 50% vol. at +40 °C), dairy products, diluted acids and alkaline solutions.
Advantages of the hose:

- Optimally visible media transport
- Extreme flexibility
- Good medium resistance

Straight screw-in fitting, 7/8-14 UNF o., Pipe exterior Ø 16 mm, PN max. 400 bar, A/F1 30, A/F2 27, galvanised steel, UNF threat
Male connector, male thread UNF, heavy type

Wear part set for stainless steel casting pressure regulator and stainless steel casting filter regulator, Size 1, G 1/4 and G 3/8

Nipple for couplings I.D. 19, Bright brass, G 3/4 IT, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

Fitting elbow 95, flat sealing, IT/IT Rp 3/4, black malleable iron fitting, Operating temp. -20 °C to 200 °C, ISO 7-1
Maximum temperature and maximum operating pressure should not occur at the same time!

According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Push-in T-fitting »Blue Series«, L-shape, rotating, M5 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 25 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight screw-on fitting, »value line«, G 1/8 i., for hose 8/6 mm, AF 14, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

Product inlet/outlet size : Ø300 mm
SPA-4-B-FI-FO-ST-Ex-D-B
SKU: SPAB000064
Stock *: 0
Max. capacity: 150 m³/h
Electro bullet magnets have a powerful bullet-shaped electromagnetic magnet core. They are suitable for filtering medium to large ferrous contaminants from high capacity coarse free-fall bulk flows.Often used in eg. the bulk, animal feed, plastics, ceramics and recycling industries.Electro bullet magnets are automatic cleaning, which makes them suitable for automatic production processes. Because they need a valve box, their installation height is much larger than that of the permanent bullet magnets.

Electromagnet
Capture Fe particles from 0.1 mm
Automatic cleaning (discontinuous)
Overall height 950 to 2433 mm
ATEX II 1/2 D possible

Application

Filtering iron contamination out of high capacity coarse product streams

For filtering ferrous contaminants – such as iron and steel – out of granulates, fibres and coarser materials in high capacity non-pressurized pipelines.
 
Bullet magnets are used in the bulk, animal feed, plastics, ceramics and recycling industries, among others.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
Electro bullet magnets have a large, cylindrical electromagnet core, with a powerful, deeply penetrating magnetic field. The magnetic core has 3 magnetic poles on which trapped ferrous particles are held. The magnetic core can be switched on / off electrically. A valve box is mounted under the pipe magnet in order to be able to automatically discharge the falling ferrous particles.
 
Summary of important specifications

1 bullet-shaped magnet with 60° top cone
Magnet quality: 2000 gauss on magnet surface
Robust steel / stainless steel housing
Finish: painted
Incl. door sensor (open/close safety switch)
Incl. control box
Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Default versions

Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)

Options

Magnet iron saturation signaller 'Met-alert Watch dog'
Kobaflex PU protective coating


Working principle

Cleaning / disposal of caught metal contaminations

How does the magnetic filtering work?
Because the magnetic core is located in the middle of the product stream, the bullet magnet has a very high separation yield. The round shape of the housing and the magnetic core (with a 60° top cone) ensures continuous flow and good distribution of the product stream. The product then passes three powerful magnetic fields, where guide strips redirect any product near the outer walls back toward the magnetic core.
 
The magnets attract passing ferrous particles. The captured particles stick to 1 of the 3 magnet poles, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Fully automatic cleaning. After you have stopped the product flow, give the start signal for the cleaning. The magnetic core is switched off electrically during cleaning. The valve box automatically discharges the falling ferrous particles.
 
Cleaning / iron discharging sequence

Stop the product flow
Give the start signal for a cleaning cycle locally, or from your central control
a. The valve box is switched to iron discharging position
b. The magnet is switched off
c. The captured ferrous particles fall off and are discharged via the valve box
d. The valve box is switched back to production position
e. The magnet is switched on again
Restart the product flow

Lifting eye nut DIN 582 M10 steel C15E galvanized ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E zinc-plated.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458710

Key steel DIN 6880 16 x 10 x 1000 mm material stainless steel 1.4571
Material: Stainless steel 1.4571. Standard length about 1000 mm.

Article ID: 61991610

Ball transfer unit 384 size 25,4 total height 44,5mm housing steel with KTL "anti-oxide" electrophoretic coating
Material: Housing: Steel, with KTL “Anti-Oxide” electrophoretic coating.  Ball cup: Steel, case hardened.  Balls: Steel 100Cr6, hardened. Heavy duty ball transfer unit for high load. High shock resistance. Very low friction. Orientation: Anyway. From size 25.4 with felt seal. With drain hole. Conveying speed max. 2m/sec.Temperature range -30°C to +160°C. 1) Elliptical flange with 2 bores. 2) Not countersunk. Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.
Article ID: 65438426

Filling unit »FUTURA«, electr. actuated with solenoid 24 V AC, 50 Hz, Size 2, G 3/8, Exhaust G 1/2, Input pressure 2.5 - 10 bar
The filling unit protects devices connected downstream by ensuring a gradual build-up of pressure.
The unit consists of a 3/2-way valve including silencer and a filling valve (start-up valve).
It is connected and disconnected by means of the 3/2-way valve.
The filling time can be altered by turning the adjusting screw.

Closing nipple locking on both sides, Bright brass, G 3/8 IT, I.D. 7.5, Operating pressure max. 200 bar, Temp. -20 °C to 100 °C
Hydraulic couplings, both sides sealing, for liquid media acc. to ISO 7241, B Series.

Areas of application: machine and plant engineering, manufacturing industry, chemical / pharmaceutical industry, automotive, food technology.

T-piece, 3x interior thread, G 2, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Nipple for couplings I.D. 19, Bright brass, G 1 IT, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C

Angled distributor 221, IT/IT/IT, Rp 3/4, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in T-fitting »Blue Series«, L-shape, rotating, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/4, Goods class 1.6, Measurement range 0 - 2.5 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Bushing 270, IT/IT, Rp 3/4, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Product inlet/outlet size : Ø400 mm
SPA-5-B-FI-FO-ST-Ex-D-B
SKU: SPAB000065
Stock *: 0
Max. capacity: 230 m³/h
Electro bullet magnets have a powerful bullet-shaped electromagnetic magnet core. They are suitable for filtering medium to large ferrous contaminants from high capacity coarse free-fall bulk flows.Often used in eg. the bulk, animal feed, plastics, ceramics and recycling industries.Electro bullet magnets are automatic cleaning, which makes them suitable for automatic production processes. Because they need a valve box, their installation height is much larger than that of the permanent bullet magnets.

Electromagnet
Capture Fe particles from 0.1 mm
Automatic cleaning (discontinuous)
Overall height 950 to 2433 mm
ATEX II 1/2 D possible

Application

Filtering iron contamination out of high capacity coarse product streams

For filtering ferrous contaminants – such as iron and steel – out of granulates, fibres and coarser materials in high capacity non-pressurized pipelines.
 
Bullet magnets are used in the bulk, animal feed, plastics, ceramics and recycling industries, among others.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Short description
Electro bullet magnets have a large, cylindrical electromagnet core, with a powerful, deeply penetrating magnetic field. The magnetic core has 3 magnetic poles on which trapped ferrous particles are held. The magnetic core can be switched on / off electrically. A valve box is mounted under the pipe magnet in order to be able to automatically discharge the falling ferrous particles.
 
Summary of important specifications

1 bullet-shaped magnet with 60° top cone
Magnet quality: 2000 gauss on magnet surface
Robust steel / stainless steel housing
Finish: painted
Incl. door sensor (open/close safety switch)
Incl. control box
Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)


Options

Available accessories & options

Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.
 
Default versions

Incl./excl. ATEX II 1/2D certificate (dust-explosion safe)
Incl./excl. valve box for iron disposal
Round or square outlet flange (for types excl. valve box)

Options

Magnet iron saturation signaller 'Met-alert Watch dog'
Kobaflex PU protective coating


Working principle

Cleaning / disposal of caught metal contaminations

How does the magnetic filtering work?
Because the magnetic core is located in the middle of the product stream, the bullet magnet has a very high separation yield. The round shape of the housing and the magnetic core (with a 60° top cone) ensures continuous flow and good distribution of the product stream. The product then passes three powerful magnetic fields, where guide strips redirect any product near the outer walls back toward the magnetic core.
 
The magnets attract passing ferrous particles. The captured particles stick to 1 of the 3 magnet poles, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Fully automatic cleaning. After you have stopped the product flow, give the start signal for the cleaning. The magnetic core is switched off electrically during cleaning. The valve box automatically discharges the falling ferrous particles.
 
Cleaning / iron discharging sequence

Stop the product flow
Give the start signal for a cleaning cycle locally, or from your central control
a. The valve box is switched to iron discharging position
b. The magnet is switched off
c. The captured ferrous particles fall off and are discharged via the valve box
d. The valve box is switched back to production position
e. The magnet is switched on again
Restart the product flow

Ball knob DIN 319 press on type ø40 for shaft diameter 10mm
Material PA: Thermoplast (Polyamide PA6 GV), glass-fibre reinforced, impact resistant, black matt.Version M = With conical bore.Recommended shaft tolerance: h9. Shaft d5 is not included in the delivery.

Article ID: 66434010

Bevel gearbox DZA, size 2, type A, i=1:1
General data: 4 sizes. Ratio either 1 : 1 or 2 : 1. Any mounting position possible. Input shaft / output shaft, speed: At both types and both ratios, the input can be at shaft A as well as at shaft B. At ratio 1:1 the maximum speed is 1400 rpm. Ratio 2:1 can be used for gearing down and also for gearing up. Gearing down: Input at shaft A with max. speed 1400 rpm (output speed max. 700 rpm). Gearing up: Input at shaft B with max. speed 750 rpm (output speed max. 1500 rpm). Housing: Thick-walled, one-piece cast aluminium housing, fully oil-tight and dust-proof. Gearing: The gears are to the Coniflex system, case hardened. Shafts/bearing system: Input and output shaft are ground and mounted on ball bearings. From size 2 with keyways.Lubrication/maintenance: Lubricated for life, viscosity ISO VG 150. Gearboxes are maintenance free. Angular backlash: 15 to 30 angular minutes. Permiss. operating temperature: -18°C to +80°C. * Permiss. radial force for FA=0. ** Permiss. axial force for FR=0.

Article ID: 41001200

Ball transfer unit 368 size 25,4 total height 44mm housing steel with KTL "anti-oxide" electrophoretic coating
Material: Housing: Steel, with KTL "Anti-Oxide" electrophoretic coating.  Ball cup: Steel, case hardend.  Balls: Steel 100Cr6, hardened. Heavy duty ball transfer unit for high load. High shock resistance. Very low friction. Orientation: Anyway. From size 25.4 with felt seal. With drain hole. Conveying speed max. 2m/sec. Temperature range -30°C to +160°C. * Bore size. Recommended bore tolerance: H9.Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.

Article ID: 65436826

Filling unit »FUTURA«, electr. actuated with solenoid 24 V AC, 50 Hz, Size 2, G 1/2, Exhaust G 1/2, Input pressure 2.5 - 10 bar
The filling unit protects devices connected downstream by ensuring a gradual build-up of pressure.
The unit consists of a 3/2-way valve including silencer and a filling valve (start-up valve).
It is connected and disconnected by means of the 3/2-way valve.
The filling time can be altered by turning the adjusting screw.