hose clamp DIN 3017-1 type W1 steel zinc plated diameter range 30-45mm band width 9mm
Material: Steel, zinc-plated (type W1). High-performance hose clamps with worm gear thread, for fixing hoses, bellows and for similar usage. Band width 9 mm. Band thickness 0.6 mm. With hexagon screw head size 7 mm, with cross recess and slot. Other sizes and versions on request.
Article ID: 63811045

Clamp collar for splined hub DIN 14 KN 21x25 diameter 62mm red brass Rg7
Material: Red brass (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64865600

Service unit 3-part »FUTURA-mini«, Metal container, Compact pressure gauge, Size 0, G 1/4, Control range 0.5 - 10 bar, Fully-auto.
Three-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Locking screw, Hexagonal socket and flange G 1 1/4, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Short stroke cylinder »ASQ« single-acting, Magnet, Piston Ø 50, Stroke 10, G 1/4, Working pressure 2-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ20, Stroke60, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled screw-in fitting G 1/8 o., for hose 4/10 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Push-in Y-connector, Plug nipple 8 mm »Blue Series«, reducing, for hose exterior Ø 6 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Hose sleeve, nickel-plated brass, rotating, G 1/4 ET, I.D. 8, Operating pre. 0 - 35 bar, Temp. 0°C to 70°C

Bushing 270, IT/IT, Rp 3/8, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

High performance V-belt XPA EPDM datum length 1532 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291532

Frequency:50 Hz
Speed:2980 1/min
Shaft Output:111032 W
Volume Flow:19407 m³/h
Pressure:Δp s16180 Pa
Pressure:Δp t17304 Pa
Density:43862 kg/m³
Sound Pressure:109 dB(A)

Length : 150 mm
SVM-N-204x55-0150-B-F1M
SKU: SVMN020150
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

CH130RFR General features
Auxiliary input for minimum window and/or thermostat contact using an external probe.
Screwed terminals.
Double insulation.
Electric features
Power supply from 2 AA type batteries of 1,5V.
Remote actuator with 5 output relays, voltage 250 Vac.
Contacts rating 5(3)A.

spherical washer DIN6319 PTFE-coated inner-Ø 6,4mm outer-Ø 12mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with conical seat DIN 6319.
Article ID: 65598406

Glycerine pressure gauge, front ring, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range -1 / 0 bar, Ø 100
Bourdon-tube pressure gauge in standard design, with panel-mounting bezel
made of chrome-plated and polished steel.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Pipe double nipple, R 3/4, Length 120 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Pressure regulator »variobloc«, incl. pressure gauge, Size 2, G 1/2, Input pressure max. 25 bar, Control range 0.5 - 6 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the knob down.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ25, Stroke20, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Push-in L-connector »Blue Series«, for hose exterior Ø 16 mm, Working pressure max. 10 bar, Plastic / nickel-plated brass
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Metal mounting bracket, horizontal, suitable for electronic pressure switches with digital display

Hose sleeve, nickel-plated brass, rotating, G 1/4 ET, I.D. 10, Operating pre. 0 - 35 bar, Temp. 0°C to 70°C

Reducing piece 241, R 3/8 ET, Rp 1/4 IT black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Round gear rack made of stainless steel 1.4305 module 1 diameter 10mm h9 length 500mm
Material: Stainless steel 1.4305.
Outside diameter = h9 drawn.

Straight teeth, milled.
Pressure angle 20°. Tooth quality 8d25 modelled on DIN 3967.

The teeth on the gear racks are manufactured using an overhead milling cutter.
This leads to negative tolerances. Dimensions ha and h0:
up to Module 2: -0,2 mm.
Module 2,5 - 4: -0,3 mm.


Article ID: 22499631

High performance V-belt XPA EPDM datum length 1550 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291550

Locking assembly COM-B stainless steel 1.4401 bore 38mm size 38-50
Material: Stainless steel 1.4401 (SS316).

Self-centering clamping bush for small hub diametres. For low torques.
Self-locking. No axial movement during mounting.
Fit: Shaft h8. Hub H8. Mounting: Slightly oil the clamping
set before mounting, do not use molibdenum disulphide or grease. Tighten
the screws evenly and crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange, until the flange is
released.

Article ID: 61599638

Frequency:50 Hz
Speed:2980 1/min
Shaft Output:134567 W
Volume Flow:20967 m³/h
Pressure:Δp s18070 Pa
Pressure:Δp t19384 Pa
Density:43862 kg/m³
Sound Pressure:111 dB(A

Length : 350 mm
SVM-F-304x99-0350-B-F0E
SKU: SVMF050350
Stock *: 0
Type: VMF5
Advised max. installation height: 90-140 mm
Interface/connection dim's: Threaded hole M8 (4x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

ZC3 General features
Cast iron valve body.
Bronze rotating sector valve shaped to obtain a very precise regulation.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure PN6.
Maximum operating temperature – 120°C.

spherical washer DIN6319 PTFE-coated inner-Ø 8,4mm outer-Ø 17mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with conical seat DIN 6319.
Article ID: 65598408

SKF spherical roller bearing 22209 E double row inner diameter 45mm outer diameter 85mm width 23mm
Material: Bearing steel. Spherical roller bearings in premium-quality. - For very high radial load and common high axial load in both directions. - Usable at angular displacement. - Usable for high speed, with groove and 3 lubribation holes. Temperature range: -30°C to +150°C (for short time up to +200°C). Other versions or other bearing types on request.
Article ID: 64776022

Double shaft block GWD-1 ISO series 1 for shaft diameter 25mm
Material: Extruded aluminium. Matching quadro linear-bearing units KGQ-1 of the ISO Series 1. Shaft blocks are practical and robust machine elements, that provide a simple way of attaching the guiding shaft of the linear bearings on the respective machine parts. They allow true to size and, most important, cost efficient constructions. *For cylindrical screws with Allen screw according to DIN 912 or ISO 4762.

Article ID: 64640225

Glycerine pressure gauge, front ring, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 1 bar, Ø 100
Bourdon-tube pressure gauge in standard design, with panel-mounting bezel
made of chrome-plated and polished steel.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Pipe double nipple, G 1, Length 100 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Pressure regulator »variobloc«, incl. pressure gauge, Size 2, G 3/4, Input pressure max. 25 bar, Control range 0.5 - 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the knob down.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ20, Stroke60, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

T-connection »value line«, for hose exterior Ø 12 mm, Operating pressure max. 16 bar, Operating temperature -20 °C to 70 °C
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Metal mounting bracket, vertical, suitable for electronic pressure switches with digital display

Nipple for couplings I.D. 7.2-7.8, nickel-plated brass, G 1/4 IT, rotating, Operating pressure 0-35 bar, Temp. 0 °C to 70 °C

Hexagonal coupling nut, G 1/4, for sleeve size I.D. 4, 6, AF 17, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

High performance V-belt XPA EPDM datum length 1557 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291557

Frequency:50 Hz
Speed:6000 1/min
Shaft Output:710 W
Volume Flow:338 m³/h
Pressure:Δp s4050 Pa
Pressure:Δp t4515 Pa
Density:43862 kg/m³
Sound Pressure:81 dB(A)

Ferrite - reinforced 1000 mm
HRA-F-102x44-AA-1000-R-W
SKU: TBAA100054
Stock *: 0
Width: 102 mm
Height: 44 mm
Water-resistant: yes
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

conical seat DIN6319 PTFE-coated inner-Ø 7,1mm outer-Ø 12mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65598506

SKF spherical roller bearing 22209 E/C3 double row inner diameter 45mm outer diameter 85mm width 23mm clearance C3
Material: Bearing steel.Spherical roller bearings in premium-quality.- For very high radial load and common high axial load in both directions.- Usable at angular displacement.- Usable for high speed, with groove and 3 lubribation holes.Temperature range: -30°C to +150°C (for short time up to +200°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64776322

Linear bearing unit KG-3-O ISO series 3 Economy-Line with self-aligning linear ball bearing with seals for shaft Ø 20mm open design
Material: Material: Housing made from extruded aluminium with an open linear bearing of the ISO Series 3 from reliable brand in good quality at low price. Self-aligning capability that accommodates tilting. All bearings are lubricated ready-to-install. Recommended shaft tolerance h6.
Article ID: 64672003

Glycerine pressure gauge, front ring, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 1.6 bar, Ø 100
Bourdon-tube pressure gauge in standard design, with panel-mounting bezel
made of chrome-plated and polished steel.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Throttle check valve »Blue Series«, Supply air throttle, R 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pressure regulator »variobloc«, incl. pressure gauge, Size 2, G 3/4, Input pressure max. 25 bar, Control range 0.5 - 10 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design.
The pressure setting can be locked by pushing the knob down.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ25, Stroke20, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Screw-in hose connector, G 3/4 o., for hose I.D. 19, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Metal mounting bracket, horizontal, suitable for digital pressure gauge

Hose sleeve, nickel-plated brass, rotating, G 1/4 IT, I.D. 6, Operating pre. 0-35 bar, Temp. 0°C to 70°C

Hexagonal coupling nut, G 1/4, for sleeve size I.D. 9, AF 17, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

High performance V-belt XPA EPDM datum length 1582 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291582

Frequency:50 Hz
Speed:4600 1/min
Shaft Output:636 W
Volume Flow:418 m³/h
Pressure:Δp s3027 Pa
Pressure:Δp t3263 Pa
Density:43862 kg/m³
Sound Pressure:96 dB(A)

Length : 550 mm
BAR-HT-23-550-25-1M6-NW-B
SKU: SBANA100010-550
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

CH120RF General features
CH120RF room thermostat shows the current settings, temperature and humidity levels and regulates the temperature in the zone in which it is installed, by communicating with the O60RF and CH175 actuators in the zone.
Zone heating, cooling and humidity control;
3 settable temperatures: COMFORT, ECONOMY and OFF
Lock function with password;
Standard time management;
White positive backlight LCD;
It can control up to 15 wireless actuators, O60RF or CH175;
Electric features
Power supply: 2 batteries AA 1,5V;
Contacts rating 5(3)A / 250Vac
Free voltage contacts
Connection to boiler heating/air-conditioning systems or dehumidifier: 3 screw terminals (contact switching NC and NO);
Type of action: 1BU (micro disconnection);
Software: A class
Auxiliary input for floor probe;
Electrical insulation: double insulation
Pulse voltage: 4000V;
Transceiver frequency: 868MHz
Maximum radio frequency power transmitted < 10mW

conical seat DIN6319 PTFE-coated inner-Ø 9,6mm outer-Ø 17mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65598508

Precision spur gear made of steel 16MnCr5 module 2 36 teeth bore 25mm hardened and ground outside diameter 76mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2.
Teeth, bores and faces ground.

Tooth quality 7 e25.
Pressure angle 20°.

Feather Keyways in accordance with DIN 6885/1, tolerance P9.
Position of keyway to tooth is not defined.

Article ID: 24183625