PKD General features
Kits composed of Sicurgas gas leak detectors P21 – P22 and safety solenoid valves normally open or normally closed.
Available for methane gas and LPG detection.
Electric features
Shockproof insulating material casing.
Internal visual and acoustic alarms.
Sicurgas has three warning lights: green LED – indicates that the detector works properly, yellow LED – indicates detector failure, red LED – indicates the gas presence in the environment (ALARM).
Semiconductor sensor for gas detection (can be replaced).
Sensor life time approximately 5 years from installation.
The used relay is sealed and filled with inert gas, which ensures in any case the absolute absence of sparks during switching phases.
Internal switch for choosing the functioning mode of the relay: stable or impulse.

Spur gear made of polyketone die-cast with hub module 0.7 15 teeth tooth width 6mm outside diameter 11,9mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28201501

Sliding hub FA size 01 torque adjustable 5-35 Nm outer diameter 58 mm max. bore: 22mm
Material: Steel, zinc-plated and chromated. - High-quality version. - The slipping torque can be adjusted with common assembly tools for screws, also after mounting. - By mounting additional springs, the torque range can be increased. (additional springs have to be ordered separately). - The hubs are delivered with pilt bore and max. bush length. Customized bores, keyways and bush lengths at extra charge. Required bush length: The bush length required depends on the width of the component to be joined. To calculate the bush length take the width of the component and add 1.5 times the thickness of the friction disc, plus an additional 0.5mm. Bush length in mm = 1.5 x s + b + 0.5.
Article ID: 61210100

Profile damper TR 93-57 diameter 93mm thread M8
Material: Co-Polyester Elastomer. The profile damper TR is a maintenance-free, self-contained damping element. The radial deformation provides a very soft deceleration with a progressive energy absorption towards the end of the stroke. The excellent temperature characteristic of the material provides consistent damping performance over a temperature range of -40°C to +90°C. The low installed weight, the economic price and the long operating life of up to 1 million cycles makes this an attractive alternative to hydraulic end position damping, if the moving mass does not need to stop in an exact datum position and it is not necessary to absorb 100% of the incoming energy. The life cycle is up to 20 times longer than for urethene dampers and up to ten times longer than for rubber springs. Environment: Resistant to oil, grease seawater and to microbe or chemical attack. Excellent UV and ozone resistance. Material does not absorb water or swell. Dynamic Force Range: 218 N to 7,500 N. Temperature Range: -40°C to +90°C. Energy Absorption: 25% to 45%. Material Hardness: Shore 40D. Mounting: in any position. Impact Velocity range: up to max. 5 m/s. Mounting Bolt Torque: M5: 4 Nm. M6: 6 Nm. M8: 20 Nm. On request: special strokes, characteristics, spring rates, sizes and materials. Download Energy-Stroke Characteristics 0.7 MB 1) Max. energy capacity per cycle for continuous use. 2) For a single cycle, e.g. an emergency stop.
Article ID: 69129300

Glycerine pressure gauge, front ring, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 16 bar, Ø 100
Bourdon-tube pressure gauge in standard design, with panel-mounting bezel
made of chrome-plated and polished steel.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Elbow 2a, short, 90°, IT/IT, Rp 2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ63, Stroke60,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjustable L screw conn., cone seal, 360° swivel range, female nut M16x1.5 i., Pipe ext. Ø 8, PN max. 630 bar, galvanised steel

Stopper, Hexagonal, G 1, AF 38, Working pressure max. 20 bar, Stainless steel 1.4408

Push-in L-fitting »Blue Series« mini, rotating, R 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Rem. Double threaded nipple, Interior / exterior thread, flat sealing, G 3/8, Working pressure max. 10 bar, Stainless steel 1.4408

T-reducer supports, for hose I.D. 6/4/6 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

High performance V-belt XPA EPDM datum length 1657 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291657

Frequency:50 Hz
Speed:2835 1/min
Shaft Output:536 W
Volume Flow:467 m³/h
Pressure:Δp s2513 Pa
Pressure:Δp t2774 Pa
Density:43862 kg/m³
Sound Pressure:78 dB(A)

5-ways solenoid valve

Length : 500 mm
BAR-ES-23-500-25-1M8-NW-B
SKU: SBAQA100030-500
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (1x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

OT.. General features
Asynchronous single-phase tubular motor.
Operation with switch, button or radio using the form OCR1.
Electromechanical stroke end.
2 adjustable stroke end points.
Stroke adjustment via adjustment cams.
Exit pin with spline shaft.
Continuous operating time 4 min
Electric features
Power supply: 230V 50Hz
Type of cable: H05VVF white
Cable length: 2,5 meters
Conductor: 4×0,75 mm2

Ball knob DIN 319 PF version E made from plastic with threaded bush of steel ball diameter 20mm
Material PF31: Duroplatic PF31 (phenolic resin), impact resistant, black, high-gloss finish.Version E = With threaded bush of zinc-plated steel.Size 16/M4 threaded bush made from brass.      
Article ID: 66412000

Double-acting compact cylinder with magnetic piston, cylinder diameter 40mm, travel 50mm
Materials: Profile barrel: Anodised aluminium. End covers: Aluminium die-cast. Piston rod: Stainless steel (Ø 20 and 25 mm austenitic, Ø 32 and 40 mm ferritic). Piston rod seal: Polyurethane. Piston seal: Nitrile rubber. O-ring seals: Nitrile rubber. Medium: Compressed air, filtered, lubricated or non-lubricated. Standard: ISO 21287. Mode of operation: double-acting, magnetic piston, piston rod with internal thread, buffer cushioning. Operating pressure: 1 to 10 bar. Operating temperature: -5°C* to +80°C max. *With temperatures below +2°C please consider the air quality. On request also available with external thread.

Article ID: 80340050

Glycerine pressure gauge, front ring, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 40 bar, Ø 100
Bourdon-tube pressure gauge in standard design, with panel-mounting bezel
made of chrome-plated and polished steel.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Double threaded nipple, reducing, Octagonal, R 1 1/2, R 1 1/4, AF 50, Working pressure max. 20 bar, Stainless steel 1.4408

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ63, Stroke60, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male branch tee, R 1/4 o., Pipe exterior Ø 8 mm, PN max. 630 bar, a/f1 19, a/f2 14, galvanised steel
Male branch tee, conical male thread acc. to ISO 7-1, heavy type

Hexagonal coupling nut, G 1, for sleeve size I.D. 19, AF 38, Brass, Max. working pressure 25 bar, Max. operating temperature 150°C

Angled piece, interior / interior, G 1/4, AF 13, Operating pressure max. 60 bar, Operating temperature max. 150 °C, Bright brass

Worm thread hose clamp, Steel bright galvanised (W1), Clamping range 267.0 - 302.0 mm, Belt width 20.0 mm
Worm-drive type.

Extremely robust hose clamps for all applications where heavy loads occur and high forces are transmitted.

Hexagon-head screw slotted, a/f 13, bright galvanised steel, passivated blue.

Y reducing supports, for hose I.D. 4/6/4 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Rod end GT-R DIN 12240-4 series K external thread M24x2 right maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299825

High performance V-belt XPA EPDM datum length 1682 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291682

Frequency:50 Hz
Speed:2870 1/min
Shaft Output:701 W
Volume Flow:380 m³/h
Pressure:Δp s3807 Pa
Pressure:Δp t3977 Pa
Density:43862 kg/m³
Sound Pressure:81 dB(A

5-ways solenoid valve

Length : 500 mm
BAR-ES-23-500-25-2M6-NW-B
SKU: SBAQA100020-500
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M6 (2x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

OCR1 General features
White ABS anti-UV case.
Dimensions 160 x 140 x 45 mm.
Electric features
Power supply: 230V~.
Max. output current: 10(4)250V~.
Reception frequency: 433.92 Mhz.
Operating temperature: -10 ÷ 60°C.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ100,Stroke160,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Long reducer, Soft sealing, G 1 1/4 o., G 1 i., PN max. 400 bar, AF1 50, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Female hinge model for articulated male hinge model, ISO 15552, ISO 21287, Ø125, 4 screws, 1 bolt and retainer
Female hinge model

Male branch tee, R 1/2 o., Pipe exterior Ø 14 mm, PN max. 630 bar, a/f1 27, a/f2 19, galvanised steel
Male branch tee, conical male thread acc. to ISO 7-1, heavy type

Hexagonal coupling nut, G 1, for sleeve size I.D. 25, AF 38, Brass, Max. working pressure 25 bar, Max. operating temperature 150°C

Angled piece, interior / interior, G 1/4, AF 13, Operating pressure max. 60 bar, Operating temp. max. 150 °C, nickel-plated brass

Jaw coupling with hose connection, I.D. 13 (1/2"), with brass seal, Malleable cast iron, galvanised/yellow passivated, max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Push-in L-fitting »Blue Series« mini, Long, rotating, M3, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Feather key DIN 6885 version A 2 x 2 x 12 mm material C45
Material: C45K.Version A.
Article ID: 61800500

Splined hub with flange DIN 14 KN 18X22 length 45mm red brass Rg7
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64855100

Rod end GT-R DIN 12240-4 series K external thread M24x2 left maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299925

High performance V-belt XPA EPDM datum length 1700 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291700

Frequency:50 Hz
Speed:2830 1/min
Shaft Output:681 W
Volume Flow:381 m³/h
Pressure:Δp s3678 Pa
Pressure:Δp t3849 Pa
Density:43862 kg/m³
Sound Pressure:81 dB(A)

5-ways solenoid valve

Length : 500 mm
BAR-ES-23-500-25-2M8-NW-B
SKU: SBAQA100040-500
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (2x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

PKD General features
Kits composed of Sicurgas gas leak detectors P21 – P22 and safety solenoid valves normally open or normally closed.
Available for methane gas and LPG detection.
Electric features
Shockproof insulating material casing.
Internal visual and acoustic alarms.
Sicurgas has three warning lights: green LED – indicates that the detector works properly, yellow LED – indicates detector failure, red LED – indicates the gas presence in the environment (ALARM).
Semiconductor sensor for gas detection (can be replaced).
Sensor life time approximately 5 years from installation.
The used relay is sealed and filled with inert gas, which ensures in any case the absolute absence of sparks during switching phases.
Internal switch for choosing the functioning mode of the relay: stable or impulse.

Neoprene timing belt HTD 14M width 55mm Lw 1400mm 100 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17731400

Precision double universal joint WDR DIN 808 bore 14H7 stainless steel 1.4301 total length 119mm outer diameter 25mm
Material: Stainless steel 1.4301. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques only amount to 90% of the single precision universal joints, stainless. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199729

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ100,Stroke160, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Short reducer, Soft sealing, G 1 o., G 1/4 i., PN max. 400 bar, AF1 41, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Female hinge model for articulated male hinge model, ISO 15552, Ø200, 4 screws, 1 bolt and retainer

Silencer, Stainless steel 1.4401, G 1/2, AF 23, Operating pressure max. 8 bar, Operating temperature -10 °C to 250 °C

Bellows suction cup, Round 2.5 folds, Material NBR, »FG«, suitable connection nipple IT G 1/8, ET M5 / G 1/8, Ø14mm
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Soft, flexible foldsSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Long reducer, Soft sealing, G 1/2 o., G 3/8 i., PN max. 630 bar, AF1 27, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Mini ball valve, nickel-plated brass, Butterfly handle, Medium/ambient temp. -10 °C to 90 °C, G 3/8 IT/ET, PN max. 10 bar

Push-in L-fitting »Blue Series« mini, Long, rotating, M5, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Feather key DIN 6885 version A 6 x 6 x 35 mm material C45
Material: C45K.Version A.
Article ID: 61812700