Clamp collar for splined hub DIN 14 KN 28x34 diameter 78mm steel C45Pb
Material: Steel C45Pb, from Ø 70 C45 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05.
Article ID: 64860900

High performance V-belt XPZ EPDM datum length 1612 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091612

Frequency:50 Hz
Speed:2880 1/min
Shaft Output:1553 W
Volume Flow:1100 m³/h
Pressure:Δp s3322 Pa
Pressure:Δp t3392 Pa
Density:43862 kg/m³
Sound Pressure:91 dB(A)

With Filter Mat, With 4 Flat Fans Weight:2,6

Magnet width : 300 mm
MAGNETIC SWEEPER NdFB D23x300
SKU: SEMV030020
Stock *: 0
Type: Bar type - manually operated
Magnetic system: Permanent Neoflux® magnet
Magnetic brooms sweep up iron and steel parts from clean or rough floors or sandy surfaces. In short, in places where iron is not or very difficult to sweep together or is not visible, such as in sand.The brooms collect metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds. Fast and easy cleanable.

Push manually or tow as a trailer
Permanent magnet
Magnet width 300-1600 mm
Quick cleaning through use of extractor plates
Engineering, production & service

Application

Sweeping floors to clean them from iron particles

Magnetic brooms (magnetic sweepers) 'sweep up' iron particles from clean or rough floors or sandy surfaces. They work well in areas where it is very difficult to sweep up iron (or just the iron and nothing else) or it is not visible, such as in sand.
 
The strong magnet in the broom collects metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds.

Types

We have standard types and 'specials' available

In addition to the standard magnetic brooms on this page, we are happy to make a special broom for you on request. Other dimensions or attachments for forklift forks or trailers, etc.

Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Cleaning (iron disposal)

Cleaning & discharging of caught iron particles

Bar magnet type
The bar magnet has a scraper ring, with which you can slide the captured iron particles to the side. There the iron automatically falls from the bar housing.
 
Plate magnet type
This type of magnetic broom contains a strong plate magnet with a hinged separator plate (extractor plate) in front. After the floor has been swept the separation plate can be swung away, causing the iron particles to automatically fall off. It can then easily be swept up with a dustpan and broom.

Conical seat DIN 6319 diameter 17mm for bolt diameter 8mm steel hardened
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65550800

Elastic coupling RNH with half shell clamps backlash-free size 28 boreholes 24mm outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552824

3/2 solenoid valve, single-sided magnet magnet type 1 voltage 24V DC port G1/8
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85011811

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ80, Stroke275,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male hinge model, ISO 15552, ISO 21287, Ø40, with 4 screws
Male hinge model

Cross fitting, Pipe exterior Ø 20 mm, PN 400, A/F1 36, A/F2 27, galvanised steel
Cross-fitting, heavy type

Syphon in U shape with welded connection to the pressure relief side, according to DIN 16282, G 1/2, made of CrNi steel 1.4571
Suitable as a cooling section for liquids, gases or steam during pressure measurements.
The use of a siphon permits the medium to cool down to a temperature that is compatible with the pressure gauge and protects the gauge against pulsating media. The condensate that forms in the siphon prevents the hot medium from entering the pressure gauge. We recommend filling the siphon with cooling sealing liquid prior to using the pipe.

Straight screw-in fitting, NPT 1/2 o., Pipe exterior Ø 15 mm, PN max. 315 bar, A/F1 27, A/F2 24, galvanised steel, NPT threat
Male connector, male thread NPT, light type

Bellows suction cup, Round 2.5 folds, Material NBR, »FG«, suitable connection nipple IT G 1/8, ET M5 / G 1/8, Ø12mm
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Soft, flexible foldsSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Plug-in connector for couplings I.D. 2.7, Stainless steel 1.4305, Sleeve I.D. 3, Operating pressure 0-35 bar, Temp. -25°C to 200°C

Angled fitting, rigid, R 1/8 o., for hose 8/6 mm, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, POM

High performance V-belt XPZ EPDM datum length 1632 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091632

Frequency:50 Hz
Speed:2895 1/min
Shaft Output:4913 W
Volume Flow:3464 m³/h
Pressure:Δp s3748 Pa
Pressure:Δp t3970 Pa
Density:43862 kg/m³
Sound Pressure:97 dB(A)

3 Fans, Single Row, 1 Height Unit Weight:2,8

O60RF General features
Power supply: 2 AA batteries 1.5V;
Battery life: approx. 2 years based on a standard use;
Transceiver frequency: 868MHz;
Max. radiofrequency transmitted power: < 10mW;
Protection degree: IP 30;
Operating temperature: 0 ÷ 50°C;
Storage temperature: -20 ÷ +70°C;
Shell: white ABS;
Compact case;
Shell size: 48x63x74mm;
Internal temperature sensor.
Electric features
Power supply: 2 AA batteries 1.5V;

Elastic coupling RNH with half shell clamps backlash-free size 28 boreholes 25mm outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552825

3/2 solenoid valve single-sided magnet magnet type 1 voltage 230V 50/60Hz port G1/8
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85011812

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ80, Stroke275, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male hinge model, ISO 15552, ISO 21287, Ø63, with 4 screws
Male hinge model

Pressure switch changeover contact, Bayonet connector, galvanised steel, Ambient temperature -25 °C to 85 °C, G 1/8, 0.5 - 2 bar
Special pressure switches for critical (water) or outdoor applications. Maximum degree of protection IP67 when a bayonet coupling is used for the electrical connection.

Pipe double nipple, R 1, Length 200 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Straight push-in fitting »metallica«, G 1/4 i., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight push-in fitting »click-clock«, G 1/2 i., for hose exterior Ø 12 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Plug-in connector for couplings I.D. 2.7, Stainless steel 1.4305, Sleeve I.D. 4, Operating pressure 0-35 bar, Temp. -25°C to 200°C

Rem. double threaded nipple, conical sealing, R 1/8 o., R 1/8 o., Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Ball knob DIN 319 PF version C made from plastic ball diameter 20mm
Material PF31: Duroplatic PF31 (phenolic resin), impact resistant, black, high-gloss finish.Version C = With compression-moulded thread.Size 45/M10 is not part of the DIN 319.

Article ID: 66402000

High performance V-belt XPZ EPDM datum length 1637 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091637

Frequency:50 Hz
Speed:2925 1/min
Shaft Output:5175 W
Volume Flow:3752 m³/h
Pressure:Δp s3729 Pa
Pressure:Δp t3914 Pa
Density:43862 kg/m³
Sound Pressure:97 dB(A)

With Filter Mat, With 4 Flat Fans Weight:2,82

Length : 200 mm
SVM-N-114x34-0200-B-F1M
SKU: SVMN060200
Stock *: 0
Advised max. installation height: 65-80 mm
Height: 34 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

C801 General features
C801 controls up to 8 wireless radiator thermostats model O81RF
The warm water flow into the radiators is managed through O81RF according to the room temperature and thepreset values in order to allow a good comfort and cost saving on heating.
Radio frequency: 868,3 MHz
Range: 100 mt free field
Battery life: approx 2 years
LCD dimensions: 33 x 20 mm.
Dimensions 86 x 86 x 21,5 mm.
Electric features
Supply voltage: 3V (2 batteries 1,5V AA).

Elastic coupling RNH with half shell clamps backlash-free size 28 boreholes 28mm outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552828

Hand Operator GR/I for 1-2 actuators
Material: housing made of shock resistant black plastic. For use with actuators and control boxes GR/I. With one hand operator, 1-4 actuators can be oprated seperately. For control boxes with 24V DC or 230V AC. For 1 actuator, 1-2 actuators or 1-4 actuators. To operate each actuator seperately. Protection class IP54. cable length approx. 2m. Actuators, control box and hand operator have to be ordered seperately.
Article ID: 47519202

Polyurethane DUO hose (PUR), Temperature range -35 °C to 60 °C, Hose Ø 10x8 mm, PN at 20 °C max. 9 bar, Roller length 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to oils, greases, aliphatic hydrocarbons and oxygen.
Suitable for vacuum.

Trunnion mounting, »CA« type for standard cylinder »SE« and »SAI«, for piston Ø 63
Male hinge model, »CA« type

Pressure switch changeover contact, Bayonet connector, galvanised steel, Ambient temperature -25 °C to 85 °C, G 1/8, 1 - 10 bar
Special pressure switches for critical (water) or outdoor applications. Maximum degree of protection IP67 when a bayonet coupling is used for the electrical connection.

Dirt strainer nickel-plated brass, Sieve insert mesh width 0.05 mm, Operating temp. -20°C to 110°C, G 1 1/4, DN 32, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Screw-on hose connector, G 1/4 i., for hose I.D. 10, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Bulkhead fitting, M26x1.5 o., G 3/8 i., AF1 27, AF2 32 nickel-plated brass Max. working pressure 25 ba, Max. operating temp.150 °C
Suitable for air, water, oil, steam, etc.

Straight screw-in fitting, G 1/9 o., for hose 4/12 mm, AF 22, Working pressure max. 10 bar (20°C)/max. 1 bar (60°C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Reducing nipple, R 1/4 o., G 1/8 i., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Feather key DIN 6885 version A 2 x 2 x 16 mm material C45
Material: C45K.Version A.
Article ID: 61800800

High performance V-belt XPZ EPDM datum length 1650 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091650

Frequency:50 Hz
Speed:2935 1/min
Shaft Output:5179 W
Volume Flow:3595 m³/h
Pressure:Δp s3806 Pa
Pressure:Δp t4047 Pa
Density:43862 kg/m³
Sound Pressure:97 dB(A)

Stainless Steel 1.4301, With Gasket Weight:3

Adapter set from square to round #250-Ø250
REDUCER DN250 EN1092-1
SKU: A333_030000
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

Intellitherm C57 General features
Front cover for batteries extraction.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Microprocessor and CMOS circuits.
Double insulation.
Protection degree IP20.
Unit weight 0,22 Kg.
Electric features
Contacts rating: 5(3)A 250Vac.
Type of action: 1BU (micro disconnection)
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.

Elastic coupling RNH with half shell clamps backlash-free size 28 boreholes 32mm outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552832

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 1/4, Control range 0.1-1 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Pivoting fork fastening, »CB« type for standard cylinder »SE« and »SAI«, for piston Ø 63
Female hinge model, »CB« type

Pressure switch changeover contact, Bayonet connector, galvanised steel, Ambient temperature -25 °C to 85 °C, G 1/4, 0.5 - 2 bar
Special pressure switches for critical (water) or outdoor applications. Maximum degree of protection IP67 when a bayonet coupling is used for the electrical connection.

Elbow 40, 45°, Rp 2 IT, R 2 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in fitting »Blue Series« mini, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Double threaded nipple 280, ET/ET, R 2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Adjustable angle fitting, Sealing cone, 360° rotating, Nut M18x1.5 i., Pipe exterior Ø 12 mm, PN max. 315 bar, galvanised steel