Knurled nut DIN 466 M3
Material: Steel, tensile strength 5, visible face precision turned, black oxide finish. * Size M12 is not part of the DIN.
Article ID: 65372300

Self-aligning linear bearing KB-3-A ISO series 3 with seals for shaft Ø 50mm
Self-aligning linear bearings series 3 of ISO standard 10285 from premium brand in top quality. High load-bearing capacity, due to the asymmetric position of the rows of balls and the specially shaped raceway segments. These linear bearings can be fitted inside a closed or open housing and are thus adjustable. With wiping double-lip seals. These bearings are self-aligning up to +/- 0,5°. Bearings with FW 5mm must be lubricated before use. All other bearings are lubricated ready-to-install. Recommended shaft tolerance h6, housing tolerance H6 or JS6. Stainless version on request.
Article ID: 64615006

Polyurethane timing belt AT10 width 32mm Lw 1080mm 108 teeth 32 AT10/1080
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. AT timing belts only run on AT pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16881700

Handheld tyre gauge, quick connector, Pressure gauge Ø 80 mm, uncalibrated, 0-4 bar/56 psi, with plug-in nipple I.D. 7.2
These pressure gauges are effectively protected against shock and impact by means of a free-standing plastic cap. They can be loaded against gauge pressure and up to the maximum scale value.
With push-in plug for DN 7.2 coupling.

RIEGLER Brass spray, Weather resistant, for metal coating for protective / decorative purposes, Temp. max. 300 °C, 400 ml
Weatherproof sprays for protective or decorative metal coatings.

Seal set (wear part), for standard cylinder, Piston Ø 63, PU seal
Set of gasket (parts subject to wear)

T-piece, Interior / interior / interior, G 1/4, Operating pressure max. 150 bar, Operating temp. -20 °C to 150 °C, Stainless steel

Straight screw-on fitting G 3/8 i., for hose 6/8 mm, AF 22, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Straight push-in bulkhead connector »Blue Series«, M12x1, for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Mini ball valve, Rotating handle, nickel-plated brass, Medium/ambient temp. -10 °C to 80 °C, Rp 3/8 IT, DN 7, PN max. 10 bar

Reducing nipple short type G 1/4 o., G 1/8 i. AF 17 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

High performance V-belt XPZ EPDM datum length 1462 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091462

Frequency:50 Hz
Speed:2850 1/min
Shaft Output:616 W
Volume Flow:787 m³/h
Pressure:Δp s2098 Pa
Pressure:Δp t2209 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

With Filter Mat Weight:2,2

Ferrite - reinforced Tapered-after roller
HRA-F-102x44-BB-0335-R-B
SKU: TBBB033514
Stock: 4
Width: 102 mm
Height: 44 mm
Length: 335 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Intellitherm C58 General features
Front cover for batteries extraction.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Microprocessor and CMOS circuits.
Double insulation.
Protection degree IP20.
Unit weight 0.22 Kg.
Electric features
Contacts rating: 5(3)A 250Vac.
Type of action: 1BU (micro disconnection)
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.

Neoprene timing belt HTD 14M width 40mm Lw 3500mm 250 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17714200

Polyurethane timing belt AT10 width 32mm Lw 1150mm 115 teeth 32 AT10/1150
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. AT timing belts only run on AT pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16881800

Filter for high pressures up to 40 bar, with manual bleeder valve, 40 µm, G 1/2, Medium temperature max. 60 °C
Centrifugal separators with a sintered filter element.

RIEGLER Copper spray, Weather resistant, for metal coating for protective / decorative purposes, Temp. max. 300 °C, 400 ml
Weatherproof sprays for protective or decorative metal coatings.

Compressed air / liquid gun, infinitely variable, POM, Temp. -20 °C to 60 °C PN max. 16 bar, Nipple I.D. 7.2 (compressed air)
This multifunctional blow gun effectively cleans surfaces with compressed air, water or cooling lubricant. Meets OSHA safety standards when dead-ended. Precise flow is achieved by adjustable flow settings. Nozzle adjusts from narrow jet to wide beam. Ergonomic, non-slip grip with built-in anti-whip function.

T-piece, interior / exterior / interior, G/R 1/4, Operating pressure max. 150 bar, Operating temp. -20°C to 150°C, Stainless steel

Straight push-in bulkhead connector »Blue Series«, M14x1, for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Thread adapter, Aluminium, ET M12x1.25, IT G 1/4, Length 26 mm

Double threaded nipple, Conical, R 3/8 a., R 1 a., AF 36, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Worm thread hose clamp, Chrome steel 1.4016 (W2), according to DIN 3017, Clamping range 50.0 - 70.0 mm, Belt width 12.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, bright galvanised steel, passivated blue.

Shaft collar DIN 705 A set screw with slot bore 5mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62300500

High performance V-belt XPZ EPDM datum length 1470 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091470

Frequency:50 Hz
Speed:2820 1/min
Shaft Output:600 W
Volume Flow:788 m³/h
Pressure:Δp s2040 Pa
Pressure:Δp t2151 Pa
Density:43862 kg/m³
Sound Pressure:80 dB(A)

With Filter Mat, Emc Weight:2,2

Length : 350 mm
BAR-N-23-350-25-1M6-NW-B
SKU: SBAMA100010-350
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Drip feed oiler system UNIKUM drip dosing at the top capacity 315 ml thread G 1/2"
Material: pickled brass. Vase glasses up to Ø 80 mm made from acrylic glass, above made from natural glass. With instantaneous shutting off, with turnable replenishing bowl, easy visual inspection of drop fall.

Article ID: 68040800

Polyurethane timing belt AT10 width 32mm Lw 1210mm 121 teeth 32 AT10/1210
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. AT timing belts only run on AT pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16881900

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 80, Stroke 40, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Seal set (wear part), for standard cylinder, Piston Ø 32, NBR seal
Set of gasket (parts subject to wear)

Counter bearing, »CR« type for standard cylinder »SE«,»SAI«,pistonØ125, only in connection with pivoting fork fastening type »CB«
Counter-hinge model, »CR« type (only in conjunction with female hinge model, »CB« type)

Fitting elbow 97, flat sealing, IT/ET, Rp 2, R 2, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galvanised
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

2/3 Tube fitting, G 1 x 19 mm, swivel nut, taper seat, heavy-duty type, Brass with a bare metal surface

Straight screw-in supports, R 1 o., for hose I.D. 25 mm, AF 32, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Kamlok cap plug, DP type, Stainless steel 1.4401, Size 1 1/4, Plug Ø 46 mm, Operating pressure max. 16 bar, Temp. -20 °C to 95 °C
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1/2, Length 100 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Feather key DIN 6885 version A 5 x 5 x 15 mm material C45
Material: C45K.Version A.
Article ID: 61809600

High performance V-belt XPZ EPDM datum length 1487 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091487

Frequency:50 Hz
Speed:2860 1/min
Shaft Output:1489 W
Volume Flow:1535 m³/h
Pressure:Δp s2270 Pa
Pressure:Δp t2522 Pa
Density:43862 kg/m³
Sound Pressure:79 dB(A)

Llx-800-Sw, 100-240Vac, 4.000Lm, 26W Weight:2,26

Length : 350 mm
BAR-N-23-350-25-1M8-NW-B
SKU: SBAMA100030-350
Interface/connection dim's: Threaded hole M8 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

ECCS15GSA – ECCS20GSA General features
Autonomous hydraulic unit: super dry magnetic transmission.
Long-term performances: pressure-tight casing, sealed with O-ring.
Mechanical register with REED contact.
REED cable with 2 mt length, not extendable.
10 litres/pulse.
R(Q3/Q1)= 25.
Standard reading capacity: 9999.999 m.
Minimum displayed value: 0.001 m³.

Neoprene timing belt HTD 14M width 40mm Lw 3850mm 275 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17714500

Polyurethane timing belt AT10 width 32mm Lw 1250mm 125 teeth 32 AT10/1250
Material: Cast polyurethane (PU) with steel tensile member. Timing belts in metric dimensions. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. AT timing belts only run on AT pulleys. Special length: Open-length timing belts made of thermoplastic TPU can be welded to endless belts at customized lengths.
Article ID: 16882000

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 80, Stroke 40, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 80°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, G 1/2 o., Pipe exterior Ø 20 mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Compact cylinder »ACP«, double-acting, Piston Ø 40, Stroke 85, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Extension pipe 900 mm with multijet nozzle

L-ring piece, for hollow screw G 1/4, for hose exterior Ø 8 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 70 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Angled fitting, Pipe exterior Ø 8 mm, PN max. 315 bar, AF1 17, AF2 12, galvanised steel
Union elbow, light type

Straight screw-on fitting G 1/8 i., for hose 9/12 mm, AF 22, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Bracket 90, 90°, Rp 1/2 IT, Rp 1/2 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Feather key DIN 6885 version A 5 x 5 x 16 mm material C45
Material: C45K.Version A.
Article ID: 61809700

High performance V-belt XPZ EPDM datum length 1500 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091500

Frequency:50 Hz
Speed:2870 1/min
Shaft Output:1513 W
Volume Flow:1555 m³/h
Pressure:Δp s2274 Pa
Pressure:Δp t2533 Pa
Density:43862 kg/m³
Sound Pressure:79 dB(A