Reduction, Pipe exterior Ø Bushing 12/10 mm, PN max. 315 bar, AF1 17, AF2 19, AF3 AF 22, galvanised steel
Reducer, light type

T-ring piece, for hollow screw G 1/8, for hose exterior Ø 4 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 70 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

T-connection POM, for hose exterior Ø 15 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Plug-in connector for couplings I.D. 5, bright brass, Sleeve I.D. 6, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Adjusting ring DIN 705 A set screw with slot bore 11mm zinc-plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388011

High performance V-belt XPZ EPDM datum length 1750 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091750

Frequency:50 Hz
Speed:2925 1/min
Shaft Output:6602 W
Volume Flow:3207 m³/h
Pressure:Δp s5172 Pa
Pressure:Δp t5353 Pa
Density:43862 kg/m³
Sound Pressure:96 dB(A)

Pk 50, 50W, 24V Dc Weight:3,28

Length : 350 mm
BAR-HT-23-350-25-2M6-NW-B
SKU: SBANA100020-350
Interface/connection dim's: Threaded hole M6 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

L02A.. – L02C.. – L02D.. General features
Code LT312U: power supply transformer 230/12V 50/60Hz 3VA;
Code LS130: NTC10k probe;
Code LS120: PTC1000 probe;
Code LS140: PT100 probe;
Code LS150: thermocouple J probe.
Electric features
Power supply: 12Vac/dc ± 10%, 2W (L02AI-/L02CI-/L02DI-)
Power supply: 110 – 230Va c±10%, 50/60Hz, 3W (L02AM-/L02CM-/L02DM-)

Inner chain link type 4 / B for roller chain 08 B pitch 1/2x5/16"
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.
Article ID: 10500100

5/3 solenoid valve magnet on both sides magnet type 1 voltage 24V DC port G1/4 Off-position: all ports closed
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85052811

Rod end PF short version bore 20mm internal thread M16 right relubricateable
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Short version. Available only with internal thread. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates.
Article ID: 63442000

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 3/8, Control range 0.1-1 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Throttle check valve, Supply air throttle (»V«) push-in connector hose 10, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For fine regulation of a cylinder piston speed in the forward and return motion and precise control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece.
Can be screwed directly onto the valve or cylinder.
Compact type of construction, also ideal where space is restricted.
On the version with a knurled screw, the set volumetric flow rate can be locked with the hexagon nut to obtain a fixed setting.

Check valve, Inclined seat design, Brass, Medium / ambient temp. max. 80 °C, Rp 2, PN max. 10 bar, Opening pressure 0.5 bar

Screw-on hose connector, G 1 1/2 i., for hose I.D. 50 mm, AF 55, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Locking screw, Exterior hexagonal, G 1/2, AF 24, nickel-plated brass, Max. working pressure 25 bar Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

T-ring piece, for hollow screw G 1/8, for hose exterior Ø 8 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 70 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Nipple for couplings I.D. 7.2 - 7.8, »stream line«, hardened / galvanised steel, for hose 10x6.5, Operating pressure max. 16 bar

Y hose connection supports, for hose I.D. 10 mm, Bracket 90°, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

High performance V-belt XPZ EPDM datum length 1762 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091762

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:7812 W
Volume Flow:2970 m³/h
Pressure:Δp s6502 Pa
Pressure:Δp t6777 Pa
Density:43862 kg/m³
Sound Pressure:99 dB(A

Pk 50 Hk, 50W, 24V Dc Weight:3,3

Length : 350 mm
BAR-HT-23-350-25-2M8-NW-B
SKU: SBANA100040-350
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

L02A.. – L02C.. – L02D.. General features
Code LT312U: power supply transformer 230/12V 50/60Hz 3VA;
Code LS130: NTC10k probe;
Code LS120: PTC1000 probe;
Code LS140: PT100 probe;
Code LS150: thermocouple J probe.
Electric features
Power supply: 12Vac/dc ± 10%, 2W (L02AI-/L02CI-/L02DI-)
Power supply: 110 – 230Va c±10%, 50/60Hz, 3W (L02AM-/L02CM-/L02DM-)

Spur gear made of polyketone die-cast with hub module 0.5 27 teeth tooth width 3mm outside diameter 14,5mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28102701

5/3 solenoid valve magnet on both sides magnet type 1 voltage 230V 50/60Hz port G1/4 Off-position: all ports closed
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85052812

Rod end PF short version bore 20mm internal thread M16 left relubricateable
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Short version. Available only with internal thread. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates.
Article ID: 63447000

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 3/8, Control range 0.1-2 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Throttle valve, Both sides throttling (»B«) push-in connector hose 10, G 1/4, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
On the version with a knurled screw, the set volumetric flow rate can be locked with the hexagon nut to obtain a fixed setting.

Pressure regulator, continuous pressure supply »variobloc«, Size 1, G 1/4, Input pressure max. 25 bar, Control range 0.5 - 6 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side. The pressure setting can be locked by pushing the knob down. By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Compact cyl.ISO 21287, single-acting, female piston rod,retr.,magnet,PistonØ16,Stroke25,M5,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 3/8, Length 180 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Nipple for pushbutton safety couplings I.D. 6, ISO 6150 C, Stainless steel, G 3/8 ET, max. 12 bar, Temp. -20 °C to 200 °C

Check valve, Small design, nickel-plated brass, Medium / ambient temp. max. 70 °C, G 1/4, PN max. 10 bar, Opening pressure 0.2 bar

Push-in T-fitting »Blue Series« mini, rotating, R 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

High performance V-belt XPZ EPDM datum length 1787 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091787

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:7938 W
Volume Flow:2985 m³/h
Pressure:Δp s6568 Pa
Pressure:Δp t6857 Pa
Density:43862 kg/m³
Sound Pressure:99 dB(A

Pk 50-Hd, 50W, 24V Dc Weight:3,32

Length : 250 mm
SVM-F-204x92-0250-B-F0E
SKU: SVMF040250
Stock: 4
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (4x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

L03B.. General features
Inputs: NTC 10k.
Operating temperature -10 ÷ 50 ° C.
Frontal protection degree IP40 if correctly installed behind the panel.
ON / OFF button on the front.
Resolution 0.1(-19.9÷99.9), 1 °C
Possibility to connect PT1000 (LS120, not included) instead of NTC 10K.
Electric features
Power supply L03BI- 12Vac/dc ±10%, 3W – L03BM- 230Vac±10%, 50/60Hz, 3W
Relay outputs (L03B—) OUT1 16(4)A 240Vac, OUT2 16(4)A 240Vac

Spur gear made of polyketone die-cast with hub module 0.7 13 teeth tooth width 6mm outside diameter 10,5mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28201301

5/3 solenoid valve magnet on both sides magnet type 1 voltage 24V DC port G1/4 Off-position: port 2 and 4 vented
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85062811

Rod end BR-R DIN 12240-4 series K internal tread M16 right with spherical ball bearing stainless
Material: Outer part: Stainless steel, forged, hardened. Bearing race superfinished.Inner ring and rollers: Stainless steel, hardened, superfinished. Lubrication: Aluminium-complex-soap-grease,approval according to NSF H1, -45ºC to +120ºC.If required special lubricants. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63299416

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 3/8, Control range 0.2-4 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

L-multi-distributor »Blue Series«, 3-fold, rotating, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pressure regulator, continuous pressure supply »variobloc«, Size 1, G 1/4, Input pressure max. 25 bar, Control range 0.5 - 16 bar
Diaphragm pressure regulators with self-relieving design for mounting side by side. The pressure setting can be locked by pushing the knob down. By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line.

Compact cyl.ISO 21287, single-acting, female piston rod,retr.,magnet,PistonØ20,Stroke5,M5, Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Angled screw-in fitting POM, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Nipple, I.D. 10, Hardened / nickel-plated steel, R 1/2 ET, PTFE coated, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Push-in T-fitting »Blue Series«, L-shape, rotating, G 3/8 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in T-fitting »Blue Series« mini, L-shape, rotating, R 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

High performance V-belt XPZ EPDM datum length 1800 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091800

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:7362 W
Volume Flow:3070 m³/h
Pressure:Δp s5857 Pa
Pressure:Δp t6149 Pa
Density:43862 kg/m³
Sound Pressure:101 dB(A)

With Z-Line-Filter And Gasket Weight:3,4

Ferrite - reinforced 1000 mm
HRA-F-102x44-AA-1000-R-B
SKU: TBAA100014
Stock *: 0
Width: 102 mm
Height: 44 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

B11AN General features
Elements in contact with the fluid are in stainless steel, laser welded.
Metallic frame.
Cover in shockproof thermoplastic material.
Output connections with PVC cable gland.
Connection G 1/4.
Maximum temperature of the controlled fluid: 120 °C.
Pressure switch body admissible temperature: -35 ÷ 60°C.
Storage and transport temperature: -35 ÷ 60 °C.
Unit weight: 0,47 Kg.
Electric features
Rated insulation voltage Ui 415V~
Continuous duty rated current Ith 16A

KL-retainer steel zinc plated size 14 for bolt diameter 14mm
Material: Spring steel, zinc plated.KL retainers are used to fix parts on shafts or bolts in axial direction. They can get mounted and dismounted very easily. They are intended for connections which must be disassembled more often. It is necessary to ensure that there is no unwanted strong contact to the retainer, because it is easily to remove.* Max. transmittable force, static, on shafts with min. strength 500 N/mm².** Depending on the shaft diamater.
Article ID: 63781301

5/3 solenoid valve magnet on both sides magnet type 1 voltage 230V 50/60Hz port G1/4 Off-position: port 2 and 4 vented
Materials: Housing and base plates: Aluminium, Spindle: Stainless steel; Piston, spacers and cover: Plastic; Static and dynamic seals: NBR; Screws: zinc-plated; Springs: Stainless Steel. Standard pilot controls with replaceable solenoid system for all common voltages. The valves are suitable for lubricated or non-lubricated standard compressed air. At normal operating conditions the system has a lifespan of 50 million switching cycles. The valve system (cartridge) is an optimised version of the million-times proven sealing system. Manual override with detent.

Article ID: 85062812