Reducing nipple, Short design, G 1/4 ET, M5 IT, AF 17, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Feather key DIN 6885 version A 3 x 3 x 10 mm material C45
Material: C45K.Version A.
Article ID: 61803100

High performance V-belt XPZ EPDM datum length 1662 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091662

Frequency:50 Hz
Speed:2910 1/min
Shaft Output:2513 W
Volume Flow:1493 m³/h
Pressure:Δp s3900 Pa
Pressure:Δp t3992 Pa
Density:43862 kg/m³
Sound Pressure:91 dB(A

Pm 50, 50W, 24V Dc Weight:3,04

Intellitherm C57 General features
Front cover for batteries extraction.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Microprocessor and CMOS circuits.
Double insulation.
Protection degree IP20.
Unit weight 0,22 Kg.
Electric features
Contacts rating: 5(3)A 250Vac.
Type of action: 1BU (micro disconnection)
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.

Elastic coupling RNH with half shell clamps backlash-free size 28 boreholes 35mm outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552835

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 1/4, Control range 0.1-2 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Plug nipple pipe DN 6, Brass 2.0401, Pipe exterior Ø 10 mm, AF 11, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Pressure switch changeover contact, Bayonet connector, galvanised steel, Ambient temperature -25 °C to 85 °C, G 1/4, 1 - 10 bar
Special pressure switches for critical (water) or outdoor applications. Maximum degree of protection IP67 when a bayonet coupling is used for the electrical connection.

Filter element 0.01 µm, Borosilicate-Aluminium, for special filter »Standard«, Size 1, G 1/4 and G 3/8

Straight push-in fitting »Blue Series« mini, round, G 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Threaded plate for the T-nut, for compact cylinder, Standard cylinder, Threaded plate M4
Threaded plate for T-slot

Pipe double nipple 23, ET/ET, Black steel, R 3, Length 120.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Locking screw, Hexagonal socket, without flange, R 1/4 nickel-plated brass Max. working pressure 25 bar Max. operating temp.150 °C
Suitable for air, water, oil, steam, etc.

Feather key DIN 6885 version A 4 x 4 x 25 mm material C45
Material: C45K.Version A.
Article ID: 61807100

High performance V-belt XPZ EPDM datum length 1687 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091687

Frequency:50 Hz
Speed:2900 1/min
Shaft Output:3299 W
Volume Flow:2013 m³/h
Pressure:Δp s3882 Pa
Pressure:Δp t4013 Pa
Density:43862 kg/m³
Sound Pressure:93 dB(A)

With Filter Mat P15/350S And Gasket Weight:3,1

Length : 530 mm
SVM-F-154x47-0530-B-F0E
SKU: SVMF020530
Stock *: 0
Advised max. installation height: 60-75 mm
Height: 47 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 1/4, Control range 0.2-4 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Bleeder valve, Aluminium, with standard nozzle, straight design, Temperature range -20 °C to 100 °C, PN max. 12 bar, Sleeve I.D. 9
Robust, ergonomic blow-off valve for continuous duty under extreme conditions.

Needle valve, Stainless steel 1.4571, Operating temperature -20 °C to 120 °C, G 1/8, DN 4, PN max. 400 bar

Plug nipple with pressure eliminator, Series B, hardened, galvanised steel, G 1/2 IT, I.D. 12.5, Operating pressure max. 300 bar
Acc. to ISO 7241-1, B Series.

This coupling series combines an extremely small pressure drop with maximum hydraulic power transmission.
Interchangeable with all couplings and plugs manufactured according to the above standard.
The patented pressure eliminator permits disconnection even if back pressure has built up (up to 200 bar).
The pressure eliminator can be used in all applications where there is a risk of pressure build-up after the line has been separated. It allows effortless connection under pressure.
The mating part must be pressureless in order for the eliminator to function optimally.

Areas of application: chemical industry, food technology, automotive, offshore.

L screw-in fitting, ET conical, R 1/8, for hose 5/3 mm, AF 8, Working pressure max. 18 bar, nickel-plated brass

Threaded plate for the T-nut, for compact cylinder, Standard cylinder, Threaded plate M3
Threaded plate for T-slot

Distributor strip, Outlets both sides, front and back, Input 2 x 1/8, Output 2 + 2 x M5, Aluminium
For easy assembly of compressed air taps (screw fittings, unions, couplings, etc.).
Optionally with 2, 3, 4, or 6 outlets on one side or both sides.

Plug-in connector for couplings I.D. 5, bright brass, Sleeve I.D. 4, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Feather key DIN 6885 version A 5 x 5 x 35 mm material C45
Material: C45K.Version A.
Article ID: 61810400

Splined hub with flange DIN 14 KN 23X28 length 55mm red brass Rg7
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64855300

Locking assembly COM-A stainless steel 1.4401 bore 24mm size 24-50
Material: Stainless steel 1.4401 (SS316).

Clamping bush for lower torques; not self-centering.
Fit: Shaft h8, Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps. Demounting: Due to the cone angle,
the clamping set is usually released once all screws have been fully
unfastened. There a three large threads cut into the front ring, which
serve to remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61599524

High performance V-belt XPZ EPDM datum length 1700 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091700

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:3452 W
Volume Flow:2029 m³/h
Pressure:Δp s4034 Pa
Pressure:Δp t4167 Pa
Density:43862 kg/m³
Sound Pressure:94 dB(A)

With Z-Line-Filter, Gasket And Weight:3,18

Length : 350 mm
BAR-HT-23-350-25-1M6-NW-B
SKU: SBANA100010-350
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Z42 – Z43 General features
Suitable for O41NCMAUX electrothermal actuator
Nominal pressure PN 16.
2-way valve in bronze.
3-way valve in nickel-plated brass.

Precision double shaft block GWD-3 ISO series 3 for shaft Ø 25mm
Material: Extruded aluminium. Matching quadro linear-bearing units KGQ-3 of the ISO Series 3. Shaft blocks are practical and robust machine elements, that provide a simple way of attaching the guiding shaft of the linear bearings on the respective machine parts. They allow true to size and, most important, cost efficient constructions. *For cylindrical screws with Allen screw according to DIN 912 or ISO 4762.

Article ID: 64642502

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 1/4, Control range 0.5-10 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

L-multi-distributor 4-fold »click-clock«, rotating, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Counter bearing, ISO 15552, ISO 21287, Piston Ø 125, with 4 screws
Counter-hinge model

Straight screw-in fitting, G 3/8 o., for hose 12/9 mm, AF 19, Stainless steel 1.4571

Dust protection hood for hydraulic couplings series A, PVC, for plug nipple I.D. 13
Acc. to ISO 7241-1, A Series.

This coupling series combines an extremely small pressure drop with maximum hydraulic power transmission.
Interchangeable with all couplings and plugs manufactured according to the above standard.
The patented pressure eliminator permits disconnection even if back pressure has built up (up to 200 bar).
The pressure eliminator can be used in all applications where there is a risk of pressure build-up after the line has been separated. It allows effortless connection under pressure.
The mating part must be pressureless in order for the eliminator to function optimally.

Areas of application: Agricultural machines, construction machines, municipal engineering, transportation engineering, industrial plant.

Straight screw-in fitting, G 1/2 o., Pipe exterior Ø 16 mm, PN bar 400, A/F1 30, A/F2 27, galvanised steel
Male connector, parallel male thread, heavy type

Push-in T-fitting »Blue Series«, rotating, R 3/8 o., for hose exterior Ø 16 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, G 3/8 o., for hose 8/6 mm, AF 19, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, POM

Feather key DIN 6885 version A 5 x 5 x 50 mm material C45
Material: C45K.Version A.
Article ID: 61810700

Locking assembly COM-A stainless steel 1.4401 bore 25mm size 25-50
Material: Stainless steel 1.4401 (SS316).

Clamping bush for lower torques; not self-centering.
Fit: Shaft h8, Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps. Demounting: Due to the cone angle,
the clamping set is usually released once all screws have been fully
unfastened. There a three large threads cut into the front ring, which
serve to remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61599525

High performance V-belt XPZ EPDM datum length 1737 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPZ are a good substitute for SPZ and 10.
Width b = 9.7 mm.

Height h = 8 mm.

Smallest medium pulley diametre = 56 mm.

Weight per Metre 0.065 kg.

Article ID: 15091737

Frequency:50 Hz
Speed:2895 1/min
Shaft Output:3625 W
Volume Flow:2232 m³/h
Pressure:Δp s4039 Pa
Pressure:Δp t4186 Pa
Density:43862 kg/m³
Sound Pressure:93 dB(A)

Pk 30 Hk + Ag 30, 30W, 24V Dc Weight:3,22

Length : 350 mm
BAR-HT-23-350-25-1M8-NW-B
SKU: SBANA100030-350
Interface/connection dim's: Threaded hole M8 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellitherm C57 General features
Front cover for batteries extraction.
Display flashing in case of low batteries charge.
Maintenance of all data during batteries replacement.
Microprocessor and CMOS circuits.
Double insulation.
Protection degree IP20.
Unit weight 0,22 Kg.
Electric features
Contacts rating: 5(3)A 250Vac.
Type of action: 1BU (micro disconnection)
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline long life batteries without connection to the electric circuit.

Inner chain link type 4 / B for roller chain 06 B pitch 3/8x7/32"
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.
Article ID: 10100100

Clamp collar for splined hub DIN 14 KN 28x34 diameter 78mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64899609

Tandem linear-bearing unit KGT-1 ISO series 1 with double rubber seal for shaft diameter 16mm
Material: Housing made from extruded aluminium with two compact linear bearings of the ISO Series 1 from premium brand in top quality, with integral double-lip seals. Lubricated ready-to-install.Recommended shaft tolerance h6. * when mounting from the bottom side choose the next smaller screw size.

Article ID: 64640316

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 1, G 1/4, Control range 0.5-16 bar, Fully
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

L-multi-distributor 4-fold »click-clock«, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Compact cylinder »ACP«, double-acting, Piston Ø 32, Stroke 100, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

High-volume blow gun »Typhoon« standard nozzle, Aluminium, Operating temperature -10 °C bis 50 °C, PN max. 10 bar, G 1/4 IT
Steplessly adjustable, lightweight and ergonomically optimised high-volume blow gun with exceptionally high blowing power.
The »Typhoon« model, which achieves approximately three times the blowing power of conventional guns, rests comfortably and securely in the hand even when full pressure is applied. Extension tubes can be supplied for blowing out inaccessible points.

In combination with safety nozzles, this blow gun meets a wide range of safety requirements.