Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ63, Stroke100, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure gauge CrNi steel design, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 16 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Quick-connect coupling I.D. 7.8, Steel, Hose connection 8x6, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Single-sided blocking, high quality and robust quick connect coupling for high flow values.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive, mining.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 6x4 mm, PN at 23 °C max. 11 bar, green, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Push-in Y-fitting »Blue Series«, rotating, R 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Closing cap, Octagonal, G 3/4, AF 32, Working pressure max. 20 bar, Stainless steel 1.4408

Check valve, Full passage, Brass, Operating temperature -10 °C to 100 °C, Rp 3/4, PN max. 40 bar, Opening pressure 20 - 50 mbar
Low-price non-return valves with full passage and very low opening pressure.

Tempered plug-in nipple DN 9, Exterior thread, Brass 2.0401, M16x1.5, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Spur gear made of stainless steel 1.4305 with hub module 3.18 (metrical pitch 10mm) 25 teeth tooth width 25mm
Article ID: 21099025

Shaft collar DIN 705 A set screw with slot bore 12mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62301200

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 24 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788124

Working width : 600 mm
RHPS-HF-06-SCS-N-SM-B-N-B-N
SKU: E0117739
Stock *: 0
Min. Fe-particle size that can be caught: 0.03 mm (Fe-parts, sporadically)
High-gradient magnetic head pulley systems are used to capture weakly magnetic particles. Due to the low magnetic field depth, this system is not suitable for high processing capacities.

Very powerful
Capture Fe and weakly magnetic particles from 0.1 mm
Continuous automatic cleaning
For belt width 600-800 mm
Max. layer thickness 30 mm

Application

Application

An extra powerful magnetic head pulley with radial magnet construction. Separate weakly magnetic and paramagnetic particles such as stainless steel and steel alloys in small, mono-layer fractions ranging in size from 0 to 40 mm - at low capacities. The high-gradient magnet is used after the separation step for the strongly magnetic ferrous particles. The total solution is a compact and maintenance-friendly conveyor belt system that can be used for applications such as:

removing stainless steel rings, springs and balls from shredded plastic bottles with pump mechanism
removing small metal particles from soil contaminants, soil or stones
removing smashed pieces of stainless steel from wood recycling processes to protect shredding blades
separating pieces of stainless steel from shredded WEEE and ASR fractions
separating iron dust from ceramics or blasting grit
separating pieces of stainless steel from cable shredder flows before the copper shredder processing step
separating stainless steel needles from plastic hospital syringes


Design

Design

The high-gradient magnetic head roller system can be divided into three segments:
 
1. Supply segment
Vibratory feeder for magnetic head pulley separator This is a stainless steel vibratory feeder, driven by two magnetic linear vibration motors. The vibration frequency is easily adjusted via the supplied control box. Advantages of these motors are the robustness, durability and maintenance-friendliness.
 
2. Middle segment
Conveyor belt for magnetic head roller separator The middle segment contains stainless steel protection covers. This means that the machine requires little maintenance, is easy to clean and can even be used for certain food applications. The sealing strips and wavy edge make product loss impossible. To achieve 9,000 gauss the thin 1.3 mm PU conveyor belt is essential to the functionality of the machine.
 
3. Discharge segment
Splitter for magnetic head pulley separator The splitter, also known as a separation partition, ensures the physical separation of the two product flows. The stainless steel splitter is designed to be adjustable both horizontally and vertically. The result: perfect separation, tailored to product flow and capacity. You can optionally choose product hoppers with the machine.

Features

Features

Through the use of high-quality magnets, the high-gradient magnetic head pulley (mounted in the head pulley) has the following characteristics:

separates weakly magnetic particles > 0.1 mm
separates ferrous particles > 30 µm (sporadic)
magnetic field depth 10 mm
radial magnet construction
neodymium magnet (10,000 gauss at the shell)


Working principle

Working principle

A high-gradient magnetic head pulley system is a conveyor belt system with a very powerful integrated magnetic conveyor roller. This powerful field is created by the combination of neodymium magnets and radial magnet construction. The result: a flux density of 9,000 gauss on the conveyor belt. The high magnetic force is necessary because the crystal lattice of stainless steel does not actually allow magnetism. However, when a stainless steel particle is processed it undergoes a number of plastic deformations caused by shredding, sieving, falling or granulating. These deformations in the stainless steel result in localized material defects in the crystal lattice. This causes the material to acquire slight or weakly magnetic properties. By the time a stainless steel particle reaches the high-gradient separator, its deformation causes it to be between 5 and 10% magnetizable. The need to deflect a weakly magnetic particle from a product flow is why the extra-high magnetic force is needed.
 
The belt is fed from a vibratory feeder, possibly in combination with a supply hopper. The belt speed is continuously adjustable. This ensures that the product supply (capacity/layer thickness), along with the attracting power of the magnetic conveyor roller and ballistic effect of the product speed, can be perfectly regulated. The splitter separates the product flow physically into a weakly magnetic metal fraction and an inert (non-magnetic) fraction.
 
A drawback of a high-gradient magnet it that it is so powerful that it also attracts other bits of magnetic material. Such as pieces of plastic, wood or rubber contaminated with iron oxide. This can result in a metal fraction contaminated with undesirable materials. In this case, the obtained product requires further purification to yield a saleable fraction.

Elastic coupling RNK with clamp hubs backlash-free size 38 boreholes 28mm outer diameter 80mm overall length 114mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Size 5 - 9: Shore hardness 92°A (gelb oder weiß). From size 14: Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With clamps, ready-to-install for rapid mounting. - Many different sizes and diameters available. - From size 14 can be exchanged with couplings RN, RNH and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60543828

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 20, Stroke 350, G 1/8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Pressure gauge CrNi steel design, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 25 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Quick-connect coupling I.D. 7.8, Steel, Hose connection 10x8, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Single-sided blocking, high quality and robust quick connect coupling for high flow values.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive, mining.

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 6x4 mm, PN at 23 °C max. 11 bar, yellow, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Push-in Y-fitting »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Short reducer, Soft sealing, G 3/4 o., G 1/4 i., PN max. 400 bar, AF1 32, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Check valve, reduced passage, Operating temperature -10 °C to 100 °C, G 1, PN max. 25 bar, Opening pressure 20 mbar
Compact, low-price non-return valves with very low opening pressure.

Screw-in hose connector, G 1/8 o., for hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Shaft collar DIN 705 A set screw with slot bore 14mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62301400

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 25 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788125

Elastic coupling RNK with clamp hubs backlash-free size 38 boreholes 32mm outer diameter 80mm overall length 114mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Size 5 - 9: Shore hardness 92°A (gelb oder weiß). From size 14: Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With clamps, ready-to-install for rapid mounting. - Many different sizes and diameters available. - From size 14 can be exchanged with couplings RN, RNH and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60543832

Spiral hose coupling set, Safety coupling I.D. 7.4, Nylon 11 PA, Hose ø 9.5x7.9, PN at 23 °C max. 12 bar, Length 2.5 m
These hoses allow gaseous and liquid media to flow safely and efficiently (Air, gases, oils, greases, fuels, organic and inorganic substances).

Thanks to their small coil diameter, they are compact, easy to handle and lightweight.
Very good recoil force owing to the use of nylon 11 (PA).

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Pressure gauge CrNi steel design, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 40 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Quick-connect coupling I.D. 7.8, Steel, Hose connection 12x9, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Single-sided blocking, high quality and robust quick connect coupling for high flow values.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive, mining.

Fitting 330, flat sealing, IT/IT, Rp/Rp 2 1/2, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Fitting elbow 96, conical sealing, IT/IT, Rp 1/2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight screw-in fitting, NPT 1/2 o., Pipe exterior Ø 12 mm, PN max. 315 bar, A/F1 22, A/F2 22, galvanised steel, NPT threat
Male connector, male thread NPT, light type

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 3x1.5 mm, PN at 20 °C max. 21 bar, natural (milky), Roll of 25 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Hollow screw, G 1/8, AF 14, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, Aluminium

Shaft collar DIN 705 A set screw with slot bore 15mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62301500

Locking assembly BAR bore 75mm
Material: Steel.

For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft. For
medium torques. Self-centering. Slight axial offset possible during
assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub
12.5µm.

Article ID: 61547500

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 30 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788130

Precision spur gear made of steel 16MnCr5 module 3 36 teeth bore 30mm hardened and ground outside diameter 114mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24383630

Elastic coupling RNK with clamp hubs backlash-free size 38 boreholes 38mm outer diameter 80mm overall length 114mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Size 5 - 9: Shore hardness 92°A (gelb oder weiß). From size 14: Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With clamps, ready-to-install for rapid mounting. - Many different sizes and diameters available. - From size 14 can be exchanged with couplings RN, RNH and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60543838

Kamlok quick-connect socket with exterior thread, B type, Stainless steel 1.4401, R 3, for plug Ø 92 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Pressure gauge CrNi steel design, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range -1 / 0 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

3/2-way miniature valve, Mechanical, Tappet, NC, Connection M5, Operating pre. 0.5 - 10 bar, Operating temp. -10 °C to 60 °C
Miniature valves, 3/2-way type, NC or NO.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 100, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Knurled nut, M18x1.5, for hose 9/12 mm, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Screw-in fitting, Aluminium, for PVC braided hose 10x4, G 1/4, Temperature range -10 °C to 60 °C, PN max. 10 bar

Vibration damper with 300 mm PVC workshop hose, plug I.D. 12, G 1/2 ET, pressed, max. 15 bar, Temp. -20 °C to 60 °C
When using pulsating tools it is recommended to observe the standard ISO 6150, § 7.1.
It recommends installing a minimum 300 mm long, flexible hose between the pulsating tool and the quick-connect coupling.

The oscillating forces are taken by the hose piece and thus increase the service life of the quick-connect coupling. No warranty can be made for couplings mounted directly on pulsating tools.

Double threaded nipple, G 1/4 o., G 1/4 o., AF 17, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Feather key DIN 6885 version A 4 x 4 x 25 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899071

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 32 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788132

Ball joint RW bore 30H7 with keyway DIN 6885-1 on both sides outer diameter 55mm steel
Material: Steel 11SMnPb30K. Max. Operating Angle 35°. Temperature range: -70°C to +160°C. Optionally without or with keyway DIN 6885-1, on both sides. The ball joints RW are simple, sliding-contact bearing elements and can only be used at low speeds. The respective maximum speeds depend on operating angle and load, but should possibly not exceed 500 rpm. The maximum torque values listed in the table are limits, which must also never be exceeded. They may only be used to their full extend with intermittent operation or at low speed and small operating angle. Can be used from -70° to +160°C.
Article ID: 63135500N

Ball head precision levelling adjuster MN 686.4 50-33.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68646500

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 40, Stroke 25, G 1/4, Working pressure 1.5 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pressure gauge CrNi steel design, Connection, rear, eccentric, G 1/2, Goods class 1.0, Measurement range 0 - 4 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Quick relief valve »lineonline«, with silencer, Hose - thread, G 3/8, for hose Ø 8 mm, Operating pressure 1 - 10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 125, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Quick-connect coupling I.D. 2.7, bright brass, Sleeve I.D. 3, Operating pressure 0 - 35 bar, Medium / ambient temp. -20°C to 100°C
One-hand quick disconnect couplings, one side sealing, extremely compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive.

Nipple for couplings I.D. 7.2 - 7.8, hardened / galvanised steel, G 1/4 IT, Operating pressure max. 16 bar, Temp. -20 °C to 100 °C

Reducing sleeve, round, G 1 i., G 3/8 i., Working pressure max. 20 bar, Stainless steel 1.4408

Cover panel for base plate, for valves connection M5, G 1/8
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

Cranked chain link type 12 / L for roller chain 081 pitch 1/2x1/8"
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel. With cranked links the power and breaking loads of the chain are reduced by 20%.
Article ID: 10200400

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 38 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788138

Working width : 600 mm
RMD-06-32-RS-F-OR-30S2
SKU: E0061054
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.