Cap bearing DIN 505 version L with bearing shells made of red brass bore 30mm D10
Material: Grey Cast Iron GG25. Bush red brass Rg7 (CuSn7Zn4Pb7-C). Bore Tolerance: ISO D10.
Article ID: 62033000

Short stroke cylinder, double-acting, Magnet, Piston Ø 32, Stroke 25, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Service unit 2-part »variobloc«, Metal container incl. viewing tube and metal drip cap, Size 1, G 3/8, Input pressure max. 20 bar
Two-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Corner blocking valve, Brass, ET, interior cone for cone connector, Operating temp. -10 °C to 80 °C, G 3/8, DN 8, PN max. 40 bar

Double threaded nipple, G 2 o., G 2 o., AF 70, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150°C
Suitable for air, water, oil, steam, etc.

Push-in T-fitting »Blue Series«, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, R 1/2 o., Pipe exterior Ø 12 mm, PN max. 315 bar, AF1 22, AF2 22, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, light type

Throttle valve, Both sides throttling (»B«) quick connector Hose 6/4, G 1/8, PN max. 10 bar, Temperature 0 °C to 70 °C
For regulation of a cylinder piston speed at both ends and control of flow rates.
Designed as a banjo-type valve with a hollow bolt and ring piece for mounting directly.
Compact type of construction, also ideal where space is restricted.

Angled fitting, rigid, R 3/8 o., for hose 12/9 mm, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, POM

Splined hub DIN 14 KN 42X48 length 70mm diameter 65mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 A/d up to size 18 x 22 = 0,15 mm, above 0,2 mm
Article ID: 64899310

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 10 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788110

Suitable for belt width : 800 mm
RHP-B406A08-080-RSD-BA
SKU: RHAN40080000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

conical seat DIN6319 PTFE-coated inner-Ø 19mm outer-Ø 30mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65598516

Spiral hose 8x12 length 0,72 - 8 mtr
Material: Polyurethane, flexible and extremely rugged. Fitting made from nickel-plated brass. The hose retracts to its original shape: the coils will not loose their original shape even under most adverse operating conditions. Data of fixed fitting on the supply side: PTFE pre-coated thread PVC coating to protect hose Data of the swivel connection on the side of the compressed-air tool: Swivelling joint with ball bearing Easy swivelling, even under pressure, no overstressing of hose coil. Max. temperature: 70ºC. Operating pressure at 20°C: Ø 5 x 8 : 9 bar Ø 6.5 x 10 : 9 bar Ø 8 x 12 : 8 bar
Article ID: 87010808

Safety ball valve, lockable, without venting hole, nickel-plated brass, Operating temp. max. 170 °C, Rp 1 1/2, PN max. 40 bar
2/2-way safety ball valves made of nickel-plated brass.
The ball valve can be locked manually.
Full bore, heavy-duty type.

Short stroke cylinder, double-acting, Magnet, Piston Ø 80, Stroke 25, G 1/4, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Storz adapter, Aluminium, Storz size 52-C, Tappet distance 66 mm, G 1 1/2 IT, Operating pressure max. 16 bar, Temp. -40°C to 110°C
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Multi-base plate for 3/2-way valve pneumatic / electropneumatic, 7 valve positions, for valves connection M5, G 1/8
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

Straight push-in connector »click-clock«, M24x1, for hose exterior Ø 14 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Protective cap for swing safety couplings »R-SC« DN 11, polyamide unbreakable

Dirt strainer, bright brass, Sieve insert mesh width 0.2 mm, Operating temp. -20 °C to 110 °C, G 3/4, DN 20, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Screw-in hose connector, R 1/8 o., for hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Ready-to-install flange nut Tr.36 x 6 single-start left material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Single-Thread, left handTolerance zone 7H.
Article ID: 64477436

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 11 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788111

Suitable for belt width : 1000 mm
RHP-B406A08-100-RSD-BA
SKU: RHAN40100000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Spur gear made of plastic PA12G with steel core module 4 25 teeth tooth width 40mm outside diameter 108mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 23455025

Sprocket set for chain tensioners, triple 10 B-3 5/8" x 3/8" Z=15
Material: Steel St40/50. The sprocket can be moved on the screw and thus be aligned with the chain. It is locked in the desired position with the nuts. The permanently lubricated 2-Z bearings are sealed on both sides and guarantee perfect running of the sprocket. Accurate-to-size spacers guarantee perfect meshing of teeth and sprocket. Temerature range: -20° to +120°C.

Article ID: 14053601

Spiral hose, Fitting and kink protection spring, PU, G 3/8, Hose Ø 12x8, PN at 23 °C max. 10 bar, Length 3.0 m
Standard type or with braided reinforcements for high pressures.

These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 80, Stroke 300, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Storz adapter, Aluminium, Storz size 52-C, Tappet distance 66 mm, G 1 1/4 IT, Operating pressure max. 16 bar, Temp. -40°C to 110°C
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Multi-base plate for 5/2-5/3-way valve pneumatic / electropneumatic, 7 valve positions, Valves connection M5, G 1/8
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

GEKA hose piece, rigid, bright brass, Connection I.D. 25, Operating pressure max. 40 bar, Medium / ambient temp. -10 °C to 90 °C
Claw couplings (claw distance: 40 mm) made of brass for water, industrial, mortar, suction and discharge hoses. Suitable for a wide range of applications, e.g. industrial plant engineering, civil and structural engineering, environmental engineering, manual trades, domestic water engineering, horticulture and landscaping, agriculture and forestry, etc.
Available in a rigid or 360° swivelling version. The two systems can also be easily coupled to one another!

Hose clamp, Malleable cast iron, 2-part, with loose tongues, Clamping range 32 - 40 mm, for hose I.D. 25 (1")

Adjustable T screw fitting, cone seal, 360° swivel range, female nut M14x1.5 i., Pipe ext. Ø 6, PN max. 630 bar, galvanised steel

Double hose connector, for hose I.D. 6 mm, Brass, Max. working pressure 25 bar, Max. operating temperature 90 °C

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 12 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788112

Suitable for belt width : 1200 mm
RHP-B406A08-120-RSD-BA
SKU: RHAN40120000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Slide set DA 5321 slide length 650mm aluminium
Material: Slide elements: Aluminium.Ball retainers and balls: Stainless steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Mounting bracket for electrical cabinets on request. Service life 40,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk/ 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. The load capacity was tested at a slide spacing of 450mm. Attention: vertical (side) mounting only.
Article ID: 64904565

Bevel gear made of steel module 2 48 teeth i=3:1 milled
Material: up to module 2: 11SMnPb30. From module 2.5: C45.Tooth quality 8 modelled on DIN 3967 (from module 2).Up to module 5 with crowned, milled teeth.From module 6 with planed teeth. Not hardened – not lapped.Shaft angle = 90º.The bevel gears only run as a pair at the stated ratio and at the same module. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module, with a different number of teeth of the same ratio.
Article ID: 36108100

Compact cylinder »ACP«, double-acting, Piston Ø 50, Stroke 35, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 80, Stroke 175, G 3/8, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Car tyre valve connector, Hose connection I.D. 6, for all tyre valves with valve thread VG 8

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ25, Stroke55, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, G 1/2 o., Pipe exterior Ø 14 mm, PN max. 630 bar, A/F1 27, A/F2 27, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 2, Length 100 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Long reducer, Soft sealing, G 3/4 o., G 1 i., PN max. 400 bar, AF1 41, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Bracket 90, 90°, IT/IT, Rp 3/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Flanged bush similar to DIN 1850 V (DIN 4379 F) sintered bronze bore 3mm outer diameter 6mm flange diameter 9mm length 10mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. Edges chamfered at 45°, at choice of the manufacturer. The
concentricity tolerance refers to d2. 1) no statement regarding the
surface roughness according to DIN 3141 (prenorm) can be given due to
the porous structure of the sintered metal. Technical Data: Surface
pressure: max. 35 N/mm², depending on speed and diameter. Temperature
range: -20°C to +120°C. Dimension r: For bores 3 - 8 mm = 0.3 mm, bores
9 - 22 mm = 0.6 mm, bores 25 - 40 mm = 0.8 mm Tolerances: Inner
diameter d1: F8 / G8. Outer diameter d2: s8. Flange diameter d3: js13.
Length b1:+/-0.1mm.Flange thickness b2: js14.

Article ID: 62350200

Double-strand sprocket ZRG with hub 12 B-2 3/4x7/16" 13 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 10,8 mm, B2 = 30,3 mm, c = 2 mm, r3 = 19 mm.Other
dimensions: See the table.

Article ID: 12788113

Suitable for belt width : 1400 mm
RHP-B406A08-140-RSD-BA
SKU: RHAN40140000
Stock *: 0
Diameter: 406 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Slide set DZ 0301 slide length 356mm zinc plated
Material: Slide elements: Cold rolled steel, zinc plated. Ball retainers: Cold rolled steel, zinc plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Low slide profile (only 35.3mm). Bracket mount for electrical cabinets on request. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings. Ordering details: e.g.: Product no. 649 034 12, Slides 0301
Article ID: 64903414

Retractable handwheel 5223 material plastic version B/G diameter 250 mm
Material: Thermoplast reinforced, impact-proof, black, matt finish. Hub bush: Steel, black oxide finish. Folding system: Steel burnished. Retractable handle: Plastic black. Use: When the handle must not stick out. The handle is firmly locked in a slim taper in the operating position. To retract the handle, it is pulled out of its taper seat and then tilted. A compression spring locks the handle in both end positions. When folding the handle away, it automatically locks in position. Version B/G: Without keyway. Version N/G: With keyway to DIN 6885-1.
Article ID: 67552500

Service unit 2-part »FUTURA-mini«, PC container, Standard pressure gauge, Size 0, G 1/4, Control range 0.1 - 4 bar, Semi-auto.
Two-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ125, Stroke60,G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Double threaded nipple, Conical, R 1 a., R 1 1/2 a., AF 50, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ32, Stroke30,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight screw-in fitting, G 3/4 o., Pipe exterior Ø 16 mm, PN max. 400 bar, A/F1 30, A/F2 32, galvanised steel, soft seal
Male connector, parallel male thread and soft seal, heavy type

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1 1/2, Length 150 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Kamlok quick-connect socket with interior thread, D type, Aluminium, G 1 1/2, for plug Ø 53 mm, Pressure max. 16 bar, max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Nipple for couplings I.D. 7.2 - 7.8, bright brass, G 3/8 IT, Operating pressure 0-35 bar, Med./ambient temp. -20°C to 100°C