Kamlok quick-connect plug, Hose sleeve, E type, Aluminium, for hose I.D. 19, Plug Ø 32 mm, Pressure max. 16 bar, Temp. max. 68°C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Push-in L-fitting »click-clock«, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Screw-on hose connector, IT, cyl. G 3/4, for hose I.D. 13 , AF 30 Brass
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Double-strand sprocket ZRG with hub 16 B-2 1"x17.02mm 12 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 15,8 mm, B2 = 47,7 mm, c = 2,5 mm, r3 = 26 mm.Other
dimensions: See the table.

Article ID: 12888112

Working width : 600 mm
RMD-06-32-RN-F-OR-30S2
SKU: E0026046
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Clamp collar single-split stainless steel 1.4305 bore 90mm with bolt DIN 912 A2-70
Material: Stainless steel 1.4305. Screw stainless steel A2-70.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62399190

Slide set DZ 2642 slide length 450mm zinc plated
Material: Slide elements: Cold rolled steel, zinc-plated. Ball retainers: Cold rolled steel, zinc-plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Low slide height. Slot or side mounting possible. Hold-in in closed position. Service life 80,000 cycles. Temperature range: -20°C to +70°C. NoteRecommended fastening: M4 screw/6mm Euro screw/4mm wood screw. Max. head. height 2mm/ Ø7.8mm. Use all mounting positions to achieve the max. load ratings.

Article ID: 64900845

Short stroke cylinder, double-acting, Magnet, Piston Ø 32, Stroke 30, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 63, Stroke 800, G 3/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Long reducer, G 3/8 o., G 1/4 i., PN max. 630 bar, Stainless steel 1.4571

3/2-way valve, Pneumatic, »3A«, monostable, NC, G 3/8, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
3/2-way pilot valves
- Pneumatic -

Push-in L-fitting »Blue Series«, rotating, Rc/R 3/8 i./o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight Check valve »Blue Series«, Hose to thread, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Nipple, I.D. 7.2-7.8, bright brass, for hose 12x9, Coupling nut, Kink protection, Operating pre. 0 - 35 bar, Temp. -20°C to 100°C

Screw-on hose connector, IT, cyl. G 3/4, for hose I.D. 16 , AF 30 Brass
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Feather key DIN 6885 version A 4 x 4 x 28 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899072

Double-strand sprocket ZRG with hub 16 B-2 1"x17.02mm 13 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 15,8 mm, B2 = 47,7 mm, c = 2,5 mm, r3 = 26 mm.Other
dimensions: See the table.

Article ID: 12888113

Working width : 800 mm
RMD-08-32-RN-F-OR-30S2
SKU: E0026048
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Bevel gear made of polyacetal resin die-cast module 1 15 teeth i=2:1 bore 5mm
Material: Polyacetal resin, die-cast. Shaft angle 90°. Bores from Module 1,5 machined. The bevel gears only run as a pair at the stated ratio. Thermoplastic materials have a far larger thermal expansion than metals. This fact must be considered with view to the crown and flank clearance when mounting the gear. Crown clearance Sk ~ 0,25 . m, flank clearance Sc ~ 0,05 . m. Thermal expansion coefficient = 1,1 . 10-4 1/°C. The bevel gears are also available with smaller bores, or with feather key groove. Additional charge worked out on time basis. Note Regarding the Gears Made of Polyacetal Resin: Inside these die-cast parts are some cavities caused by production. These parts should therefore not be drilled too deep. With larger bores or when grooving the cavities might become visible. This often does not affect the functionality. Note for ordering: These gears are sold singulary, not by pair. For a pair of bevel gears, you have to order two matching gears of the same module and ratio. At ratio 1:1, you need two pieces of the same number of teeth. At ratio uneven 1:1, you need two pieces with a different number of teeth of the same ratio.
Article ID: 35555600

Clamp collar double-split stainless steel 1.4305 bore 90mm with bolts DIN 912 A2-70
Material: Stainless steel 1.4305. Screws stainless steel A2-70.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62399490

Precision levelling adjuster MN 686.3 60-33.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For parall surfaces. Lower overall height with short adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699375

Standard cylinder, ISO 15552, double-acting, Piston Ø 32, Stroke 50, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches can be mounted in two T-slots on the same side as the compressed air supply.
The version with a 125 mm bore is provided with fixing accessories on three sides as standard.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 63, Stroke 500, G 3/8, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pipe double nipple, R 1/4, Length 200 mm, Working pressure max. 40 bar, Stainless steel 1.4571

3/2-way valve, Pneumatic, »3A«, monostable, NO, G 3/8, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
3/2-way pilot valves
- Pneumatic -

Push-in T-fitting »Blue Series«, L-shape, rotating, G 1/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Wall bracket made of brass, »speedfit« series, 1/2 BSP, for pipe exterior Ø 15 mm

Multi-base plate for 3/2-way valve pneumatic / electropneumatic, 2 valve positions, for valves connection M5, G 1/8
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

Screw-in hose connector, G 3/4 o., for hose I.D. 16, nickel-plated brass
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Double-strand sprocket ZRG with hub 16 B-2 1"x17.02mm 14 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 15,8 mm, B2 = 47,7 mm, c = 2,5 mm, r3 = 26 mm.Other
dimensions: See the table.

Article ID: 12888114

Working width : 1000 mm
RMD-10-32-RN-F-OR-30S2
SKU: E0026050
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

MAEDLER deep groove ball bearing single row inner diameter 8mm outer diameter 22mm width 7mm shielded on both sides clearance C3
Single row deep groove radial ball bearingsMaterial: Bearing steel. - Standard ball bearings in high quality. - Most common bearing type. - Usable for high speed. - Insensitive in use and maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or with contacting rubber seals 2RS. Temperature range: -20°C to +90°C (caused by type of lubrication), short-term up to 110°C.Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 608-ZZ-C3-MAE

Slide set DS 5321 slide length 300mm stainless steel
Material: Stainless steel 1.4301 Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Mounting bracket for electrical cabinets on request. Service life 10,000 / 80,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk / 6mm countersunk screw. Use all mounting positions to achieve the max. load ratings. Attention: Vertical mounting only Ordering details: e.g.: Product no. 649 440 30, Slides DS 5321
Article ID: 64944030

2/2-way solenoid valve brass, NC, directly operated, 230 V, 50 - 60 Hz, Medium temperature -25 °C to 80 °C, G 1/8, PN 0 - 12 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

5/3-way valve pneumatic, monost. G 1/2, mid-position pressurised, Operating pre. 2.5 to 10 bar, Operating temp. -10°C to 60°C

Pipe double nipple, R 3/8, Length 200 mm, Working pressure max. 40 bar, Stainless steel 1.4571

3/2-way valve, Pneumatic, »3A«, monostable, NC, G 1/4, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
3/2-way pilot valves
- Pneumatic -

Push-in L-fitting »Blue Series«, rotating, G 3/8 i./o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Flat suction cup, round, Silicone material, »PFG«, ø:3,5 suitable connection nipple ET M3
Robust and hard-wearing suction pad with a single sealing lip.
Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to handle smooth or slightly rough surfaces. Due to its flat shape, it can grip the workpiece in a very short time and withstand the forces that result from fast movement of the object during handling. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very short evacuation timesSuitable for high lateral forcesGood intrinsic stability when attached to the loadSupports on the bottomVery short cycle timesHigh suction forces with small dimensions

Applications:
Handling workpieces with smooth or slightly rough surfaces, e.g. metal sheets,
cardboard boxes, sheets of glass, plastic parts and sheets of wood.

Multi-base plate for 5/2-5/3-way valve pneumatic / electropneumatic, 2 valve positions, Valves connection M5, G 1/8
Aluminium alloy manifold bases 6061-T6 for 2 to 8 valve positions.

Screw-in hose connector, G 1/4 o., for hose I.D. 4 mm, AF 17, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Spur gear made of stainless steel 1.4305 with hub module 3 25 teeth tooth width 25mm outside diameter 81mm
Material: Stainless steel 1.4305

Milled teeth.
Tooth quality 8d25 DIN 3967.
Pressure angle 20°.


Article ID: 23399025

Double-strand sprocket ZRG with hub 16 B-2 1"x17.02mm 15 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 15,8 mm, B2 = 47,7 mm, c = 2,5 mm, r3 = 26 mm.Other
dimensions: See the table.

Article ID: 12888115

Working width : 1500 mm
RMD-15-32-RN-F-OR-30S2
SKU: E0026052
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

MAEDLER deep groove ball bearing single row inner diameter 3mm outer diameter 10mm width 4mm shielded on both sides clearance C3
Single row deep groove radial ball bearingsMaterial: Bearing steel. - Standard ball bearings in high quality. - Most common bearing type. - Usable for high speed. - Insensitive in use and maintenance. - On choice: With friction-free metal shields ZZ (= 2Z) or with contacting rubber seals 2RS. Temperature range: -20°C to +90°C (caused by type of lubrication), short-term up to 110°C.Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 623-ZZ-C3-MAE

Slide set DZ 3307 slide length 406mm zinc plated
Material: Slide elements: Cold rolled steel, zinc-plated. Ball retainers: Cold rolled steel, zinc-plated. Balls: Hardened steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Locks in open position. Fast disconnection. Bracket mount for electrical cabinets on request. Mounting accessories included. Service life 10,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M4 screw. Use all mounting positions to achieve the max. load ratings.

Article ID: 64903016

timing bar AT5 36 teeth length 160mm material aluminium
Material: Aluminium similar EN AW2017A.
Article ID: 16693600

2/2-way solenoid valve brass, NC, directly operated, 24 V DC, Medium temperature -25 °C to 80 °C, G 1/8, PN 0 - 5 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

5/3-way valve pneumatic, monost. G 1/2, mid-position exhausted, Operating pre. 2.5 to 10 bar, Operating temp. -10°C to 60°C

Pipe double nipple, R 3/4, Length 150 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Hydraulic coupling, Series A, I.D. 13, Brass, G 1/2 IT, Operating pressure max. 250 bar, Operating temp. -30 °C to 100 °C
Acc. to ISO 7241-1, A Series.

This coupling series combines an extremely small pressure drop with maximum hydraulic power transmission.
Interchangeable with all couplings and plugs manufactured according to the above standard.
The patented pressure eliminator permits disconnection even if back pressure has built up (up to 200 bar).
The pressure eliminator can be used in all applications where there is a risk of pressure build-up after the line has been separated. It allows effortless connection under pressure.
The mating part must be pressureless in order for the eliminator to function optimally.

Areas of application: Agricultural machines, construction machines, municipal engineering, transportation engineering, industrial plant.

Straight push-in fitting »metallica«, R 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

U-element for hose 6 mm, for serial set up of lineonline components

Trunnion mounting, »CA« type for standard cylinder »SE« and »SAI«, for piston Ø 40
Male hinge model, »CA« type

Cross-connection supports, for hose I.D. 6 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Double-strand sprocket ZRG with hub 16 B-2 1"x17.02mm 16 teeth material steel teeth induction hardened
Material: Steel C45, teeth induction hardened (≈ HRC 50).Pre-bored.
General dimensions: B1 = 15,8 mm, B2 = 47,7 mm, c = 2,5 mm, r3 = 26 mm.Other
dimensions: See the table.

Article ID: 12888116

Working width : 2000 mm
RMD-20-32-RN-F-OR-30S2
SKU: E0026054
Stock *: 0
Field strength (flux density) (±10%): 1800 gauss (on shell) gauss
Magnetic field depth: 100 mm
Min. Fe-particle size that can be caught: 2 mm
Easy-to-install drum magnets for the continuous separation of coarse or sharp iron particles. Various magnet strengths and types available to separate strong- or weakly- magnetic particles.

High capacity (up to 550 m³/h)
Various dimensions and flange types
With neodymium or ferrite magnets
For belt width 600-2000 mm
Suitable for sharp or abrasive particles

Application

Application

Add-on magnetic drum separators purify product streams. This takes place before the next processing step, such as non-ferrous separation or plastic sorting.
 
The undesired, weakly magnetic iron parts are then separated from the main current so that they do not interfere in the next machining step. This way you achieve a higher separation efficiency, which also results in the recovery (recycling) of a clean, salable iron fraction.
 
To achieve good separation it is important that the material is supplied in a consistent flow, which can be achieved with a vibratory feeder or conveyor belt for example.

Types

Types

Type F
The 1,800 drum magnets have an axial magnet system and are suitable for separation of ferromagnetic particles. These are built with a ferrite magnet segment, in some cases strengthened with neodymium. These drum magnets are not suitable for separation of weakly magnetic metal particles.

cost effective
axial magnet system
capture Fe particles from 2 mm
max. particle size 100 mm
magnetic field depth 100 mm
ferrite magnet

 
Type B
The 3000 gauss magnet has the same configuration as type F, however, this system is built with Neodymium magnets instead of Ferrite magnets.

axial magnet system
capture Fe particles from 0.5 mm
max. particle size 100 mm
magnetic field depth 100 mm

 
Type P
The 6,000 gauss (Power) drum magnet also has an axial magnetic system, but thanks to its high magnetic force and deep holding field it is also suitable for separation of coarse and even fine Fe particles and weakly magnetic particles such as stainless steel and other steel alloys. The magnet segment consists entirely of neodymium magnets.

axial magnet system
capture weakly magnetic particles > 0.5 mm
capture Fe particles > 0.1 mm
magnetic field depth 150 mm

 
Type H
The 8,000 gauss ('High gradient') drum magnet has a radial magnet system and is used for smaller layer thickness than the 6,000 gauss drum magnet. The 8,000 gauss is not really intended for separation of ferromagnetic particles. These may only be present sporadically, because they disrupt the magnetic field, which is detrimental to the separation of weakly magnetic metal particles. Therefore a 8,000 gauss drum magnet is usually placed at the end of a processing step (preceded by other separators).

radial magnet system
capture weakly magnetic particles > 0.1 mm
capture Fe particles > 30 µm (sporadically)
magnetic field depth 30 mm


Working principle

Working principle

In case of overfed drum magnets, the material is fed over the drum. As soon as an iron part passes through the magnet, it is attracted and carried over the drum until the part comes out of the magnetic field. The iron part is then released and falls behind a divider plate.

Flanged bush BBP bore 10mm polyamide 6.6 outer diameter 16mm length 10mm flange diameter 20mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62381300

Ball head precision levelling adjuster MN 686.8 50-26.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For non-parall surfaces up to 4° slope. Larger overall height with more adjustment travel. Without lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699860

Tubular handle 335 length 600 mm stainless steel 1.4305 / 1.4308
Material: Grip tube Ø28mm x 2 mm made from stainless steel 1.4305, silk matt gloss, ground. Feet made from stainless steel, precision cast 1.4308, matt blasted. Very high stability for small sizes. Connection between tube and foot is sealed against water spray. Other sizes on request.
Article ID: 66699562