Compressed air connection set, incl. coupling I.D. 7.2 and connector I.D. 9, for supply unit 3-Kraft

Tempered plug-in nipple DN 6, Exterior thread, Brass, M8x0.75, AF 11, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Splined hub with flange DIN 14 KN 32X38 length 60mm red brass Rg7
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64855800

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 25H7 on both sides min. length 350mm max. length 435mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199950

Suitable for belt width : 650 mm
RHP-B254A06-065-RSD-BA
SKU: RHAN25065000
Stock *: 0
Diameter: 254 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ECCF..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for cold water up to 50°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

Mounting device module 2 19°31'42" left handed for gear racks 251603xx, 251605xx and 251609xx
Material: High-quality steel. Helical tooth system, left-hand 19° 31' 42''. Milled teeth, tooth quality 8e27. Application: These left-handed racks are designed to be used in combination with our helical-toothed right-handed gear racks to simplify the mounting.

Article ID: 25160000

SKF cylindrical roller bearing NU 210 ECP single row inner diameter 50mm outer diameter 90mm width 20mm
Material: Bearing steel. Cylindrical roller bearings in premium-quality. - For high radial load. - Displaceable in both directions (type NU) or in one direction (Type NJ). - Usable for high speed, with groove and 3 lubribation holes. - Easy to mount (the inner ring is loose). Temperature range: -30°C to +90°C (for short time up to +110°C). Other versions or other bearing types on request.
Article ID: 64775112

Pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range -1 / +9 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Throttle check valve »Blue Series«, Straight, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

3/2-way solenoid valve »lineonline« controlled venting, Hose - thread, G 1/8, Hose Ø 6, NC, 24 V DC, Operating pressure 2.5-7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Mist oiler »Standard-mini« with PC container, Size 0, G 1/8, Input pressure max. 16 bar, Medium / ambient temperature max. 60 °C
Proportional lubricators in compact design, oil can be filled under pressure.

Foot fastening, »LB« type for round cylinder »MI« and »MSI«, for piston Ø 32
Foot model, »LB« type

T-piece 130, IT/IT/IT, Rp 1, T-branch reducing Rp 3/4, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in bulkhead connector »metallica«, M22x1, for hose exterior Ø 14 mm, Working pressure max. 16 bar
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Tempered plug-in nipple DN 6, Exterior thread, Brass, M10x1, AF 11, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Feather key DIN 6885 version A 3 x 3 x 20 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899038

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 25H7 with keyway DIN 6885-1 on both sides min. length 350mm max. length 435mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199950N

ZL30 General features
Controlled fluid: cold and hot water with max 50% glycol volume, superheated water and steam.
Fluid temperature controlled 5 ÷ 120 ° C.
High closing point (▲).
Stainless steel shutter.
Stem in stainless steel.
EPDM O-ring stem seal.
Flow rate characteristic: regulation port A – AB: equal percentage (VDI / VDE 2173) n (gl) = 3; bypass B – AB: linear (VDI / VDE 2173).
Leakage rate: regulation port A – AB: max 0.05% of Kvs; bypass B – AB: max. 1% of Kvs value.
External thread in accordance with ISO 228.
Red Rg5 stamped brass valve
Nominal pressure 1600 kPa.
Differential pressure Δpmax 400 kPa.

Spur gear made of polyketone die-cast with hub module 0.7 23 teeth tooth width 6mm outside diameter 17,5mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28202301

Spherical bearing DIN 12240-4-K type S with outer ring relubricateable bore 35mm outer diameter 78mm stainless steel == Initial lubrication required before use ==
Material: Inner ring stainless steel 1.4034, hardened, ground and polished.Bearing shell special brass CuZn38Al1. Outer ring stainless steel 1.4305.Dimensions according to DIN 648 / 12240-1 series K (wide version).Can be re-lubricated.Initial lubrication required before useFor high sliding speed up to 60 m/min.With outer ring (bigger outer diameter than version G or G..D).
Article ID: 63399035

SKF cylindrical roller bearing NU 210 ECP/C3 single row inner diameter 50mm outer diameter 90mm width 20mm clearance C3
Material: Bearing steel.Cylindrical roller bearings in premium-quality.- For high radial load.- Displaceable in both directions (type NU) or in one direction (Type NJ).- Usable for high speed, with groove and 3 lubribation holes.- Easy to mount (the inner ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64775412

Pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range -1 / 0 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Plastic silencer with granulate filling, G 1, Operating pressure max. 12 bar, Operating temperature -20 °C to 70 °C
With granular filling, self-cleaning.
The spherical shape of the granules allows very fine dust to escape in addition to air.
Higher blow-off rate.

3/2-way solenoid valve »lineonline« silenced venting, Hose - thread, G 3/8, Hose Ø 8, NC, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Quick-connect coupling I.D. 12, Garage coupling, Bright brass, G 1/2 ET, Pressure max. 16 bar, Medium/ambient temp. -10°C to 50°C
One-hand quick disconnect couplings, one side sealing, for high flow rates.
With rubber ring to protect against wear.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Angled screw-in fitting, R 1/8 o., Pipe exterior Ø 5 mm, PN bar 100, AF1 12, AF2 9, galvanised steel
Male elbow, conical male thread acc. to ISO 7-1, very light type

T-piece 133, Rp 1/2 IT, R 1/2 ET, Rp 1/2 IT, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Thread plug nipple »click-clock«, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar, nickel-plated brass
By combining these parts with unions, union elbows and union tees, you can obtain all essential connecting variants and simultaneously reduce your warehousing costs.

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 30H7 on both sides min. length 400mm max. length 490mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199963

Length : 640 mm
SVM-F-780x313-0640-B-F0E
SKU: SVMF070650
Stock *: 0
Advised max. installation height: 165-320 mm
Height: 385 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

K17C General features
Cable composition:– 2 conductors in solid copper and tinned copper– Outer sheath in pvc– Aluminium foil shielding– Tinned copper sheath
The heating cable includes:– 1 standard length of heating cable– 2 cold tails
Minimum installation room temperature 5 °C
Maximum room temperature 65 °C
Minimum storage room temperature -20 ÷ -25°C
Electric features
Power supply 230V-50Hz
Constant power delivered ~17W/m
Total power absorbed at 230V:– K17C29 510 W– K17C73 1260 W– K17C82 1530 W– K17C102 1750 W– K17C129 2200 W

nut DIN 934 A2 M12 RH
Material: Stainless steel V2A (A2) or V4A (A4).Hexagon nuts according to the old standard DIN 934 with metric ISO thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65299012

Spherical bearing DIN 12240-4-K type SD with outer ring maintenance-free bore 35mm outer diameter 78mm stainless steel
Material: Inner ring stainless steel 1.4034, hardened, ground and polished. Bearing shell stainless steel 1.4571, with PTFE-lining. Outer ring stainless steel 1.4305. Dimensions according to DIN 648 / 12240-1 series K (wide version). Maintenance-free.Suitable for high dynamic loads.With outer ring (bigger outer diameter than version G or G..D).
Article ID: 63399135

Pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 1 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Distributor strip, Outlets one side front, Input 2 x 3/8, Output 4 x 1/8, Aluminium
For easy assembly of compressed air taps (screw fittings, unions, couplings, etc.).
Optionally with 2, 3, 4, or 6 outlets on one side or both sides.

3/2-way solenoid valve »lineonline« silenced venting, Hose - thread, G 3/8, Hose Ø 8, NO, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Quick-connect coupling I.D. 12, Garage coupling, Bright brass, G 3/4 IT, Pressure max. 16 bar, Medium/ambient temp. -10°C to 50°C
One-hand quick disconnect couplings, one side sealing, for high flow rates.
With rubber ring to protect against wear.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Push-in L-fitting »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-in hose connector, G 1/2 o., for hose I.D. 8, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Angled fitting, Pipe exterior Ø 12 mm, AF 15, AF1 22, Operating pressure max. 60 bar, Temperature max 150 °C, nickel-plated brass

Hollow screw, Single, G 1/8, Working pressure max. 16 bar, Operating temperature -20 °C to 70 °C, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Polyurethane timing belt T10 width 100mm 100 T10 open length with tensile members from steel packed 4 x 25mm
Material: Thermoplastic polyurethane (TPU), white, with steel
tensile member.

Good resistance against oil, fats and many chemicals. Temperature range
-30º to +80ºC. T timing belts only run on T pulleys. Belts made of TPU
can be welded to endless belts. When welded, the perm. tensile force is
reduced to 50%.

Article ID: 16490000

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 30H7 with keyway DIN 6885-1 on both sides min. length 400mm max. length 490mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199963N

ECCS..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for hot water up to 90°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

nut DIN 934 A4 M12 RH
Material: Stainless steel V2A (A2) or V4A (A4).Hexagon nuts according to the old standard DIN 934 with metric ISO thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65299112

Spur gear made of POM with hub module 3 56 teeth tooth width 25mm outside diameter 174mm
Material: POM, white / nature, milled teeth. Tooth quality 10d25 DIN 3967. Pressure angle 20°. Untoleranced dimensions in accordance with DIN ISO 2768 middle. Temperature limit: continuous 100°C, only short time 160°C. Water absorption (satiable) 0,5% Cws.
Article ID: 29805600

Polyurethane timing belt T10 width 100mm 100T10 open length PAZ = Polyamide fabric on tooth side
Material: Thermoplastic polyurethane (TPU), white, with steel tensile member. With green polyamide fabric on the tooth side. Temperature range -30º to +80ºC. TPU PAZ belts can be welded to endless belts (tensile force -50%). The polyamide fabric reduces the friction on aluminium or steel plates to approx. 50%. On plastic sliding plates, the friction reduction is approx. 30%. So, depending on the application, the needed driving power is much lower. By the fabric, the wear resistance of the belt is much higher and the noise is lower. Application: for example supported transportation belt drives.
Article ID: 16490001

Pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range 0 - 1.6 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.

Straight push-in bulkhead connector reducing »click-clock«, M20x1, for hose exterior Ø 8/12 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 40, Stroke 15, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Quick-connect coupling I.D. 12, Garage coupling, Bright brass, G 3/4 ET, Pressure max. 16 bar, Medium/ambient temp. -10°C to 50°C
One-hand quick disconnect couplings, one side sealing, for high flow rates.
With rubber ring to protect against wear.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Machine and plant engineering, manufacturing industry, workshops.

Push-in L-fitting »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-connector »metallica«, for hose exterior Ø 4 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 150 °C
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

T-fitting, Pipe exterior Ø 10 mm, AF 13, AF1 19, Operating pressure max. 60 bar, Temperature max 150 °C, nickel-plated brass

Double threaded nipple »value line«, G 3/8, G 3/8, AF 19, Operating pressure max. 60 bar, Operating temperature max. 150 °C
For air, water, steam, oil, etc.

Length : 1226 mm
SVM-F-470x207-1226-F-F0E
SKU: RBPF021200
Stock *: 0
Advised max. installation height: 125-230 mm
Height: 208 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

ZC3 General features
Cast iron valve body.
Bronze rotating sector valve shaped to obtain a very precise regulation.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure PN6.
Maximum operating temperature – 120°C.

Pressure gauge CrNi steel design, Connection radial bottom, G 1/2, Goods class 1.0, Measurement range -1 / +0.6 bar, Ø 100
Bourdon-tube pressure gauge, CrNi steel type, all stainless steel.

Suitable for gaseous or liquid media which do not have high viscosity and do not crystallise,
also in corrosive atmosphere.