Angled screw-in fitting, G 1/4 o., for hose 6/8 mm, Working pressure max. 10 bar (20 °C)/max. 2.5 bar (90 °C), PP
Chemically resistant to almost all inorganic acids and bases, even in high concentrations and at temperatures greater than 90 °C.

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 18 mm, red, Operating temperature max. 90 °C, PN max. 12 bar
For fastening rigid PA or aluminium pipes to the wall.

Feather key DIN 6885 version A 3 x 3 x 16 mm material stainless steel 1.4571
Material: Stainless steel 1.4571.

Version A.

Article ID: 61899036

Clamping bush MSD bore 45mm steel
Material: Steel. The MSD clamping bush consists of a
double-walled, hardened steel sleeve filled with a special pressure
medium, a seal, a piston, a compression flange and fastening screws.
When tightening the screws, the sleeves expand evenly against shaft and
hub, creating a rigid connection. When the screws are loosened, the bush
returns to its initial position and can be easily demounted.
Concentricity: about 0,03 - 0,06 mm Tolerance: Shaft h8 - k6 (for
Product No. 615 215 00 only h7), Hub H7 Advantages: -fast
mounting/demounting -sensitive adjustment of the hub can be carried out
during assembly -low fastening torque and few screws allow very simple
assembly. -good concentricity -small dimensions allow little ouside
diametre of the hub MN = transmittable torque at load of 0. If the
screws are fastened with Manz. Fa = transmittable axial force at torque
of 0. If the screws are fastened with Manz. Manz = required fastening
torque for the screws. The dimensions refer to bushes before assembly. Temperature
range: -30° to +85°C.

Article ID: 61524500

Spherical bearing DIN 12240-4-K type GD without outer ring maintenance-free bore 40mm outer diameter 72mm
Material: Inner ring bearing steel 100Cr6, hardened, ground and polished. Bearing shell steel 9SMnPb28K, zinc plated, with PTFE-lining.Dimensions according to DIN 648 / 12240-1 series K (wide version). Maintenance-free.Suitable for high dynamic loads.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63334000

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 16H7 on both sides min. length 250mm max. length 320mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199932

Length : 1026 mm
SVM-F-470x207-1026-F-F0E
SKU: RBPF021000
Stock: 5
Advised max. installation height: 125-230 mm
Height: 208 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

Intellicomfort CH140GSM2 General features
ON/OFF auxiliary control for electrical utility.
Temperature adjustment range 2 ÷ 40 °C, increment 0.1°C
Room T reading/display range – 50 ÷ + 50 °C
Differential 0.3 ÷ 5 K
Thermal gradient 4 K/h
Maximum room temperature 45°C
Managements: heating and cooling, electrical utility, external probe, alarm management to exceed minimum (only on APP), summer time / Standard time, remote change over, summer/winter
Viewing of energy consumption
Correction of the offset of the temperature read
Storage temperature -10°C ÷ +60°C
Protection degree IP30
Pollution degree 2
SIM Micro SIM card slot
Quad Band EGSM 850/900/1800/1900 MHz
Output power: Class 4 (2w) per 850/900 MHz, Class 1 (1w) per 1800/1900 MHz
Sensitiveness:– 107Dbm@850/900 MHz– 106Dbm@1800/1900 MHz
Display Italian, English, French, Spanish, German, Russian
Screen lock with password
Charge reserve, for sending a power failure message (BLACK-OUT)
Electric features
Power supply 230V-50Hz
Maximum power consumption 10 W
Contact rating 5(3)A 250 Vac
Type of action 1.B.U (micro disconnection)
Outputs: relay 1 to boiler heating/cooling, relay 2 auxiliary, 3 screw clamps (closed + open)
Inputs: 1 auxiliary probe – NTC 10K – lmax 100m, section 0.5 ÷ 1.5 mm2),  2 auxiliary relays – free contacts
Internal battery for programming data and clock / calendar
Software Class A
Electrical insulation: Double insulation
Pulse voltage 4000V

Rod end BR DIN 12240-4 series K internal thread M22x1.5 left with spherical ball bearing
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Thread rolled., Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63247200

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.1 - 2 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Standard pressure gauge with front ring, black, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range -1/0 bar, Ø40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 32, Stroke 80, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Compact cyl.ISO 21287, double-acting, female piston rod,magnet, PistonØ32, Stroke10,G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Quick-connect coupling I.D. 2.7, bright brass, M5 IT, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C
One-hand quick disconnect couplings, one side sealing, extremely compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive.

Screw-in hose connector, G 1/4 o., for hose I.D. 13, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

T-multi-distributor »Blue Series«, 4-fold, rotating, R 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Tempered plug-in nipple DN 6, Exterior thread, nickel-plated brass, G 1/8, AF 11, Operating pressure max. 15 bar
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil, e.g. for cooling circuits on plastics processing machines.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Clamping bush MSD bore 48mm steel
Material: Steel. The MSD clamping bush consists of a
double-walled, hardened steel sleeve filled with a special pressure
medium, a seal, a piston, a compression flange and fastening screws.
When tightening the screws, the sleeves expand evenly against shaft and
hub, creating a rigid connection. When the screws are loosened, the bush
returns to its initial position and can be easily demounted.
Concentricity: about 0,03 - 0,06 mm Tolerance: Shaft h8 - k6 (for
Product No. 615 215 00 only h7), Hub H7 Advantages: -fast
mounting/demounting -sensitive adjustment of the hub can be carried out
during assembly -low fastening torque and few screws allow very simple
assembly. -good concentricity -small dimensions allow little ouside
diametre of the hub MN = transmittable torque at load of 0. If the
screws are fastened with Manz. Fa = transmittable axial force at torque
of 0. If the screws are fastened with Manz. Manz = required fastening
torque for the screws. The dimensions refer to bushes before assembly. Temperature
range: -30° to +85°C.

Article ID: 61524800

Spherical bearing DIN 12240-4-K type G without outer ring relubricateable bore 40mm outer diameter 72mm == Initial lubrication required before use ==
Material: Inner ring bearing steel 100Cr6, hardened, ground and polished.Bearing shell special brass CuZn38Al1.Dimensions according to DIN 648 / 12240-1 series K (wide version).Can be re-lubricated (from size size 6mm with lubrication hole).Initial lubrication required before useFor high sliding speed up to 60 m/min.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63324000

Bush similar to DIN 1850 J (DIN 4379 C) sintered bronze borehole 6mm outer diameter 9mm length 6mm
Self lubricating, oil coated, pressed ready-to-install and 1)
kalibrated. After press-fitting them into a rigid bearing housing with a
mounting hole H7, these bearings have a bore of H7. Edges chamfered at
45°, at choice of the manufacturer. The concentricity tolerance refers
to d2. 1) no statement regarding the surface roughness according to DIN
3141 (prenorm) can be given due to the porous structure of the sintered
metal. Technical Data: Surface pressure: max. 35 N/mm², depending
on speed and diameter. Temperature range: -20°C to +120°C.Tolerances:
Inner diameter F7 / G7. Outer diameter s7. Length +/-0.1mm.

Article ID: 62330905

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 16H7 with keyway DIN 6885-1 on both sides min. length 250mm max. length 320mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199932N

Suitable for belt width : 600 mm
RHP-B254A06-060-RSD-BA
SKU: RHAN25060000
Stock *: 0
Diameter: 254 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

P82 General features
Light signals: 1 red LED, power supply on, 1 yellow LED, general failure; 4 yellow LED, failure for each probe series; 4 red LED, gas alarms for each probe series.
Acoustic signals: 1 buzzer with sound intensity > 60db at 1m.
1 button to reset the alarms and for testing the probes.
Self-extinguishing plastic housing.
Dimensions: 158 x 90 x 58 mm – 9 modules complies with DIN 43880 standard.
Unit weight: 0.25 kg.
Rear panel mounting on Omega DIN EN 50022 rail.
Protection: IP20; IP40 when is properly installed in an electrical box.
Environment temperature: 0 ÷ 50 °C.
Environment humidity ±90% U.R. without condensation.
Electric features
Power supply: 12Vac/dc ± 10%.
Absorption with 1 probe approximately 160mA (320mA).
Absorption with 4 probes approximately 280mA (920mA).
Connection with 2 terminals of 2.5 mm².
Input – fuse power supply 1A 5x20mm.
4 inputs for sensors S81, S82, S83, or probes ATEX S84, S85, S86 (different gas types).
Connection to the probe with 3 terminals of 2.5 mm², for each probe: C (-12…24V); S (+4…20mA); A (+12…24V).
Maximum connection length 50 m, for each probe.
Section of 3 conductors: 1.5 mm².
Alarm output: n.1 relay with 1 SPDT contact 8A 250Vac.
Failure output: n.1 relay with 1 SPDT contact 8A 250Vac.
Outputs connections: n.3 terminals of 2.5 mm² for relay C-NC-NO.

Inner chain link type 4 / B for roller chain no. 04 pitch 6mm
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.
Article ID: 10060100

Ball head precision levelling adjuster with locknut MN 686.7 40-17.5 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. With lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699740

Elastic coupling RNH with half shell clamps backlash-free size 28 prebore 10mm (no H7) outer diameter 65mm overall length 90mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552810

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.2 - 4 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Throttle check valve »Blue Series«, Supply air throttle, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting, R 1/4 o., for hose exterior Ø 12 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ25, Stroke35, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

1/3 Tube fitting, G 1 x 25 mm, taper seat, with collar, CH type, Brass with a bare metal surface

Push-in L-fitting »Blue Series« long, rotating, G 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-in hose connector, G 1 o., for hose I.D. 25, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 22 mm, blue, Operating temp. max. 90 °C, PN max. 12 bar
For fastening rigid PA or aluminium pipes to the wall.

Clamping bush MSD bore 50mm steel
Material: Steel. The MSD clamping bush consists of a
double-walled, hardened steel sleeve filled with a special pressure
medium, a seal, a piston, a compression flange and fastening screws.
When tightening the screws, the sleeves expand evenly against shaft and
hub, creating a rigid connection. When the screws are loosened, the bush
returns to its initial position and can be easily demounted.
Concentricity: about 0,03 - 0,06 mm Tolerance: Shaft h8 - k6 (for
Product No. 615 215 00 only h7), Hub H7 Advantages: -fast
mounting/demounting -sensitive adjustment of the hub can be carried out
during assembly -low fastening torque and few screws allow very simple
assembly. -good concentricity -small dimensions allow little ouside
diametre of the hub MN = transmittable torque at load of 0. If the
screws are fastened with Manz. Fa = transmittable axial force at torque
of 0. If the screws are fastened with Manz. Manz = required fastening
torque for the screws. The dimensions refer to bushes before assembly. Temperature
range: -30° to +85°C.

Article ID: 61525000

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 20H7 on both sides min. length 290mm max. length 360mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199940

Suitable for belt width : 650 mm
RHP-B204A06-065-RSD-BA
SKU: RHAN20065000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ECCF..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for cold water up to 50°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

KL-retainer steel zinc plated size 24 for bolt diameter 20mm and 25mm
Material: Spring steel, zinc plated.KL retainers are used to fix parts on shafts or bolts in axial direction. They can get mounted and dismounted very easily. They are intended for connections which must be disassembled more often. It is necessary to ensure that there is no unwanted strong contact to the retainer, because it is easily to remove.* Max. transmittable force, static, on shafts with min. strength 500 N/mm².** Depending on the shaft diamater.
Article ID: 63781701

Slide set DZ 2907 slide length 305mm zinc plated
Material: Slide elements: Cold rolled steel, zinc-plated. Ball retainers: Plastic / zinc-plated steel. Balls: Hardened steel.Sold by pair (1 x product no. = 1 pair of slides).Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Locks in open position. Fast disconnection. Bracket mount for electrical cabinets on request. Optional clip-on brackets available. For infrequent use, service life up to 2,000 cycles. Temperature range: -20°C to +70°C. NoteRecommended fastening: M4 screw.Use all mounting positions to achieve the max. load ratings.

Article ID: 64902212

Chain tensioner SPANN-BOY® TS 05 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These very low, ready-to-install tensioners enable noise reduction and wear reduction at chain drives.Needed space below chain only 40mm.With two springs of different force, which can get activated separately or together. So it is possible to adjust three different tensioning forces.Usable travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).

Article ID: 14040830

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.5-10 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Standard pressure gauge with front ring, black, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0-1 bar, Ø 40
Bourdon-tube pressure gauge in standard design,
either with panel-mounting bezel made of chrome-plated or black sheet steel or
with 3-hole bezel made of chrome-plated sheet steel.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Spiral hose, Fitting, Kink protection spring, Fibre reinforced, PU, G 3/8, Hose Ø 12x8, PN at 23 °C max. 15 bar, Length 3.0 m
Standard type or with braided reinforcements for high pressures.

These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ32, Stroke10, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjustable male connector, with cone seal, G3/8 o., Pipe exterior Ø 12, PN max. 630, a/f1 22, a/f2 24, galvanised steel

Short reducer, Soft sealing, G 3/8 o., G 3/4 i., PN max. 400 bar, AF1 32, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Push-in Y-connector, Plug nipple 16 mm »Blue Series«, reducing, for hose exterior Ø 12 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 22 mm, red, Operating temperature max. 90 °C, PN max. 12 bar
For fastening rigid PA or aluminium pipes to the wall.

Slip shaft with joints PWNR stainless steel 1.4301 with needle bearings made of bearing steel bore 20H7 with keyway DIN 6885-1 on both sides min. length 290mm max. length 360mm
Material: Stainless steel 1.4301. Needle bearings from bearing steel.Max. Operating Angle per Joint 45°. Other lengths on request.Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199940N

Suitable for belt width : 800 mm
RHP-F324A06-080-RSD-BA
SKU: RHAF32080000
Stock *: 0
Diameter: 324 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ECCS..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for hot water up to 90°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

Ball knob DIN 319 Technopolymer PA6GV type C ø40 M10
Material PA: Thermoplast (Polyamide PA6 GV), glass-fibre reinforced, impact resistant, black matt.Version C = With compression-moulded thread.Size 16/M5, 20/M6, 25/M8, 32/M10 and 40/M12 is not part of the DIN 319.

Article ID: 66474010

Chain tensioner SPANN-BOY® TS 06 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These very low, ready-to-install tensioners enable noise reduction and wear reduction at chain drives.Needed space below chain only 40mm.With two springs of different force, which can get activated separately or together. So it is possible to adjust three different tensioning forces.Usable travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).

Article ID: 14040831

Service unit 3-part »FUTURA« with PC container, Protective cage and pressure gauge, Size 2, G 1/2, Control range 0.5-16 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Plastic silencer with granulate filling, G 3/4, Operating pressure max. 12 bar, Operating temperature -20 °C to 70 °C
With granular filling, self-cleaning.
The spherical shape of the granules allows very fine dust to escape in addition to air.
Higher blow-off rate.

3/2-way solenoid valve »lineonline« controlled venting, Hose - thread, G 1/8, Hose Ø 6, NO, 24 V DC, Operating pressure 2.5-7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Mist oiler »Standard-mini« with PC container, Size 0, G 1/4, Input pressure max. 16 bar, Medium / ambient temperature max. 60 °C
Proportional lubricators in compact design, oil can be filled under pressure.

Double threaded nipple, Cyl., G 3/4 o., G 1 o., AF 38, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

T-piece 130, IT/IT/IT, Rp 1, T-branch reducing Rp 1/2, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.