Slanted seat valve with spring return actuator

M23 General features
Press-forged brass valve body OT58 UNI 5705.
Gaskets in NBR (Buna N) – Viton.
Rod in stainless steel AISI 304.
Core in stainless steel AISI 430F.
Spring in stainless steel AISI 302.
Antivibration brass ring.
Operating temperature: -10 ÷ 90°C.

Polyamide hose PA (hard), color black outer diameter 4mm, inner diameter 2,5mm
Material: Polyamide. Dimensions and tolerances to DIN 73378. Max. length 100m. Application: Pneumatic-hose for Pneufit-Push-In or Pneufit C connectors. PA-hoses allow a higher pressure than PU-hoses, but they need a bigger radius. Max. Operating Pressure: The pressures shown in the table are valid for -40°C up to +20°C. At higher temperature note follwing factors: Temperature 30 °C: Factor 0,83. Temperature 40 °C: Factor 0,72. Temperature 50 °C: Factor 0,64. Temperature 60 °C: Factor 0,57. Temperature 70 °C: Factor 0,47 (max. operating temperatur).
Article ID: 86980403

Chain tensioner SPANN-BOX® size 1 short high tensioning force 12 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040407

Rod end BR DIN 12240-4 series K internal thread M20x1.5 left with spherical ball bearing
Material: Outer part: Alloyed steel, forged, quenched and tempered. Bearing race hardened, ground and lapped. Thread rolled., Surface zinc-plated and chromatised. Inner ring: Roller bearing steel, hardened, ground and polished. Lubrication: Aluminium-complex-soap-grease, approval according to NSF H1, -45ºC to +120ºC. Wide version. Dimensions according to DIN 648 / 12240 series K. Thread either right-handed or left-handed. Heavy-duty rod ends with roller bearing. very light running (basically without friction). Long-term lubricated and sealed with cover plates. For high loads.
Article ID: 63247000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 14.9 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Ball valve EN 331 DVGW, nickel-plated brass, Hand lever, IT/IT, Rp 3/8, DN 10, Operating temp. -15°C to 60°C, PN max. 5 bar (Gas)
Ball valves with full bore, for gas installations. Applications: Natural gas, LPG, town gas

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 32, Stroke 60, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

High-volume blow gun »Typhoon« standard nozzle, Aluminium, Operating temperature -10 °C bis 50 °C, PN max. 10 bar, Sleeve I.D. 6
Steplessly adjustable, lightweight and ergonomically optimised high-volume blow gun with exceptionally high blowing power.
The »Typhoon« model, which achieves approximately three times the blowing power of conventional guns, rests comfortably and securely in the hand even when full pressure is applied. Extension tubes can be supplied for blowing out inaccessible points.

In combination with safety nozzles, this blow gun meets a wide range of safety requirements.

Standard pressure gauge »pressure line« Connection, rear, centric, G 1/8, Goods class 2.5, Measurement range 0-6 bar/90 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Reduction, Pipe exterior Ø Bushing 15/10 mm, PN max. 315 bar, AF1 17, AF2 19, AF3 SW 27, galvanised steel
Reducer, light type

Fitting elbow 97, flat sealing, IT/ET, Rp 1, R 1, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galvanised
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Extension piece, short, R 1/8 o., G 1/8 i., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

High performance V-belt XPB EPDM datum length 1690 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491690

Slanted seat valve with spring return actuator

EV84A General features
Alphanumeric display and 4 functional keys for parameters easy setting.
Digital clock with charge reserve over 5 years.
Switch-on times optimization.
Electric features
Power supply: 230V 50Hz.
Consumption; 4VA.
3 output relays: 1 relay to control the circulation pump, 1 relay to control valve opening, 1 relay to control valve closing.
3 analog inputs to control: the external temperature, the limit temperature, the delivery temperature.
1 humidistat input
1 digital input for SUMMER/WINTER switch.

Round trapezoidal nut nylatron Tr.40 x 14 P7 double-thread right length 80mm outer diameter 80mm
Material: Plastic (PA6.6 with MoS2), black. Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64594000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 19.8 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Ball valve EN 331 DVGW, nickel-plated brass, Hand lever, IT/ET, Rp/R 1/4, DN 8, Operating temp. -15 °C to 60 °C, PN max. 5 bar
Ball valves with full bore, for gas installations. Applications: Natural gas, LPG, town gas

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 32, Stroke 60, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

High-volume blow gun »Typhoon« standard nozzle, Aluminium, Operating temperature -10 °C bis 50 °C, PN max. 10 bar, Nipple I.D. 7.2
Steplessly adjustable, lightweight and ergonomically optimised high-volume blow gun with exceptionally high blowing power.
The »Typhoon« model, which achieves approximately three times the blowing power of conventional guns, rests comfortably and securely in the hand even when full pressure is applied. Extension tubes can be supplied for blowing out inaccessible points.

In combination with safety nozzles, this blow gun meets a wide range of safety requirements.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0-2.5 bar/36 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-on hose connector, G 1/4 i., for hose I.D. 12, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Silencer, Stainless steel, flat type, G 3/8, AF 19, Operating pressure 0 to 15 bar, Operating temperature -10 °C to 250 °C

Screw-in hose connector, O-ring »value line«, G 1/4, for hose I.D. 12, Operating pressure max. 60 bar, Operating temp. max. 80°C
For air, water, steam, oil, etc.

Chain KE similar to 12B-1 plastic with stainless steel
Similar to DIN ISO 606 (ex DIN 8187).Material and type:Type KE: Inner links made from special polycarbonatewith high chemical resistance, for food industry or labority.Outer links from stainless steel 1.4301.Type KE-Eco: Similar to KE, but inner links from standardpolycarbonate, with lower chemical resistance.Main dimensions according to DIN.Very light and silent running.Very clean due to closed surfaces on the inner link.High corrosion resistance.Long lifetime, without any lubrication.Breaking load significantly higher than pure plastic chains.Temperature range -10°C to +80°C.Vmax 70m/min.Sold by meter. Connecting links have to be ordered seperately.
Article ID: 10755000

Chain connecting link type 11 / E for roller chain 08 B-1 pitch 1/2x5/16" packing unit 5 pieces
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.* Company standard.** Packing units of 5 pieces.
Article ID: 10500300

High performance V-belt XPB EPDM datum length 1700 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491700

Slanted seat valve with spring return actuator

Length : 500 mm
SVM-N-114x34-0500-B-F1M
SKU: SVMN060500
Stock *: 0
Advised max. installation height: 65-80 mm
Height: 34 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

OCM1A General features
Wind alarm regulation range 5 ÷ 40 Km / h
Brightness regulation range only 0 ÷ 50 lux
Operating temperature -10 ÷ 60 ° C
ABS material case
Dimensions 120x80x50 mm
Electric features
Power supply: 230Vac 50Hz
Rain sensor power supply: 12Vdc
Relay maximum capacity: 250Vac 4A

Chain tensioner SPANN-BOX® size 1 short low tensioning force 16 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040308

Round trapezoidal nut nylatron Tr.40 x 7 single-start left length 80mm outer diameter 80mm
Material: Plastic (PA6.6 with MoS2), black. Tolerance zone 7H. Height = 2 x diameter.

Article ID: 64394000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 21 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Ball valve EN 331, DVGW, nickel-plated brass, Butterfly handle, IT/IT, Rp 3/8, DN 10, Operat. temp. -15 °C to 60 °C, PN max. 5 bar
Ball valves with full bore, for gas installations. Applications: Natural gas, LPG, town gas

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 32, Stroke 75, G 1/8, Working pressure 1.5 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

High-volume blow gun »Typhoon« standard nozzle, Aluminium, Operating temperature -10 °C bis 50 °C, PN max. 10 bar, Sleeve I.D. 9
Steplessly adjustable, lightweight and ergonomically optimised high-volume blow gun with exceptionally high blowing power.
The »Typhoon« model, which achieves approximately three times the blowing power of conventional guns, rests comfortably and securely in the hand even when full pressure is applied. Extension tubes can be supplied for blowing out inaccessible points.

In combination with safety nozzles, this blow gun meets a wide range of safety requirements.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0 - 6 bar/90 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Silencer, Stainless steel, flat type, M5, AF 8, Operating pressure 0 to 15 bar, Operating temperature -10 °C to 250 °C

Trunnion mounting, ISO 21287, Piston Ø 25, with 4 screws
Male hinge model

Worm thread hose clamp, Chrome steel 1.4016 (W2), according to DIN 3017, Clamping range 70.0 - 90.0 mm, Belt width 9.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, bright galvanised steel, passivated blue.

Washer DIN 6340 for bolt size M6 steel hardened bore 6.4mm outer diameter 17mm width 3mm
Material: Quenched and tempered steel, stamped out, pressed flat or machine straightened, hardened.

* Diameter d1 = 15mm is not part of the DIN.


Article ID: 65310600

High performance V-belt XPB EPDM datum length 1750 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491750

Slanted seat valve with spring return actuator

OT.. General features
Asynchronous single-phase tubular motor.
Operation with switch, button or radio using the form OCR1.
Electromechanical stroke end.
2 adjustable stroke end points.
Stroke adjustment via adjustment cams.
Exit pin with spline shaft.
Continuous operating time 4 min
Electric features
Power supply: 230V 50Hz
Type of cable: H05VVF white
Cable length: 2,5 meters
Conductor: 4×0,75 mm2

Chain tensioner SPANN-BOX® size 1 short high tensioning force 16 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040408

Flexible coupling EL nominal torque 20Nm long version with pilot bore overall length 80mm outer diameter 35mm
Material: Hubs 11 SMn Pb 37, from Ø 55 mm CK45. Spring: Spring steel type C. These couplings are elastic all-metal couplings and completely maintenance free. The all-metal design leads to a strong resistance against oil and higher temperatures: -40°C to +100°C. The elastic part consists of a spring body, made up of three layers of wound springs welded into the connecting hubs. The couplings are suitable for both rotating directions. They can be locked against rotation with a feather key or with pins. The couplings are pressfitted. Demounting is done by pressing or pulling off. Vibrations and shocks are largely absorbed. Depending on the length of the coupling - S, L or Db - bending of 3 - 6° or axial displacement of 3 - 6% of the nominal shaft diametre are possible. Couplings are available pre-drilled ex stock. Customized bores and feather-key grooves available at surcharge.
Article ID: 60202100

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 25 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Ball valve EN 331, DVGW, nickel-plated brass, Butterfly handle, IT/ET, Rp/R 1/4, DN 8, Operat. temp. -15°C to 60°C, PN max. 5 bar
Ball valves with full bore, for gas installations. Applications: Natural gas, LPG, town gas

Standard cylinder SAI, ISO 15552, double-acting, Piston Ø 32, Stroke 125, G 1/8, Working pressure 1.5-10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on two sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

High-volume blow gun »Typhoon« standard nozzle, Aluminium, Operating temperature -10 °C bis 50 °C, PN max. 10 bar, Sleeve I.D. 13
Steplessly adjustable, lightweight and ergonomically optimised high-volume blow gun with exceptionally high blowing power.
The »Typhoon« model, which achieves approximately three times the blowing power of conventional guns, rests comfortably and securely in the hand even when full pressure is applied. Extension tubes can be supplied for blowing out inaccessible points.

In combination with safety nozzles, this blow gun meets a wide range of safety requirements.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0 - 4 bar/60 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Screw-in fitting, Aluminium, for PVC braided hose 10x4, G 1/8, Temperature range -10 °C to 60 °C, PN max. 10 bar

Straight screw-in fitting, NPT 3/4 o., Pipe exterior Ø 20mm, PN max. 400 bar, A/F1 36, A/F2 32, galvanised steel, NPT threat
Male connector, male thread NPT, heavy type

Closing cap (hexagonal design), G 1, AF 37, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Retaining ring DIN 471 30mm
Material: Feather steel, phosphated, oiled. External rings for
axial fixing a machine part on a shaft.

Article ID: 61743000

High performance V-belt XPB EPDM datum length 1800 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491800

Slanted seat valve with spring return actuator

O24 General features
Coupled with the most common valves from DN15 to DN100 and from G1“to G2”, for the ZC (Fantini Cosmi) series up to DN150.
Single-phase synchronous motor with bidirectional rotation.
Bottom and device bracket in die-cast aluminum.
Cover and indicator made of thermoplastic material.
Angle of rotation equal to 90°.
Possibility of manual operation.
Adjustable height of the bracket, max 30mm.
Possibility to add an auxiliary microswitch for pump control, signaling etc. (optional).
Rotation torque: 15Nm.
Insulation class: I.
Screw terminals.
Fitting for smooth pipes and for spiral ducts Pg 13.5.
Reversible plate.
Electric features
Power supply: 230Vca 50Hz.
Power consumption: 4W.
Contacts rating: 6(2)A 250Vca (micro aux).

Electric drip-feed oiler ELO 230V 50Hz capacity 140ml
Material: Brass nickel-plated. Glass cylinder made from acrylic glass. Voltage: On choice: 230V AC, 50Hz, or 24V DC. Drip rate normal: about 45 drops per 1 ml. Other than the manual drip-feed oiler, which also drips when the machine has stopped, the electric drip-feed oiler only drips as long as the machine is running. When the machine stops, the electric drip-feed oiler is also automatically shut off, as the oiler is controlled via the machine programme. Finest dosing of drops is possible - by turning a knurled nut at the top part of the oiler. Almost all liquids can be dosed drop by drop, provided they are not mixed with solid matters. It is also suited for other media, provided they do not thicken with heat. Attention must be paid to the compatibility with acrylic glass and buna N used as sealing material. (possibly natural glass and vitone sealings on request). Duty cycle: intermittent 20%. Protection class acc. to EN 60529: IP20. Power consumption: 12VA (12W).
Article ID: 68030100