Spherical bearing DIN 12240-4-K type G without outer ring relubricateable bore 30mm outer diameter 55mm stainless steel == Initial lubrication required before use ==
Material: Inner ring stainless steel 1.4034, hardened, ground and polished.Bearing shell special brass CuZn38Al1.Dimensions according to DIN 648 / 12240-1 series K (wide version).Can be re-lubricated (from size 6mm with lubricatin hole).Initial lubrication required before useFor high sliding speed up to 60 m/min.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63399230

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 26 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Double threaded nipple, Conical, R 1 1/4 a., R 1 1/4 a., AF 44, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

5/2-way valve, Pneumatic, »4A«, monostable, G 1/2, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
5/2-way pilot valves
- Pneumatic -

Fitting elbow 98, conical sealing, IT/ET, Rp 2, R 2, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in L-fitting »click-clock«, rotating, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Straight screw-in fitting, Kink protection spring, G 1/4 o., for hose 8/6 mm, Working pressure max. 18 bar, nickel-plated brass

Angled screw-in fitting POM, G 1/2 o., for hose exterior Ø 15 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Locking screw, Exterior hexagonal, G 1/8, AF 14, nickel-plated brass, Max. working pressure 25 bar Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Rubber-metal buffer MGH stainless steel diameter 15mm height 8mm bore 4,3mm (for screw M4)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921150

High performance V-belt XPB EPDM datum length 1850 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491850

Slanted seat valve with spring return actuator

Length : 250 mm
SVM-N-204x55-0250-B-F1M
SKU: SVMN020250
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ECCM32 General features
The calculator features separate sections able to simultaneously record the following:• thermal energy in a heating and cooling circuit;• sanitary cold water volume;• sanitary hot water volume.
The unit has been designed to facilitate the installation and reduce the time needed for the commissioning operations.The ECCM32 unit is equipped with a wired “M-Bus” interface and a wired “Local-bus” interface that allow the user to read, by means of compatible equipment, the consumption from inside one’s own apartment.
Ambient operating temperature: +5 ÷ +55 °C
Storage temperature: -20 ÷ +55 °C
Dimensions: 141 x 77,5 x 47 mm
Degree of protection: IP52
Environmental class: A (E1, M1)
Maximum value of thermal power: 33000 kW with a pulse rate < 100 l/pulse; 330000 kW with a pulse rate ≥ 100 l/pulse
Temperature measurement range: 2 ÷ 150°C (Θmin=2°C Θmax=150°C)
Temperature difference: 3 ÷ 148°C (ΔΘmin=3°C ΔΘmax=148°C)
Heating/cooling switching: According to the sign of temperature difference between sensors (ΔΘ); in any case, no energyrecording takes place in case of –3°C < ΔΘ < +3°C
Display unit features: Liquid crystal display (LCD) with 8 digits, 19 icons and 2 auxiliary digits
Energy measurement unit on the LCD: MWh (standard), configurable kWh, MJ and GJ
Type of sensors: Pt500 sensors pairs with 2-wire lead (Platinum precision resistor, IEC 60751 compliant
Type of sensor cables: Unshielded
RMS Sensor current value: < 72 µA (measurements made every 30 seconds)
Pulse inputs: One input for the heating/cooling flow meter; two inputs for the sanitary water flow meters
Pulse inputs class: IB (in accordance with the EN 1434-2 Standard)
Pulse inputs circuit type: Pull-up (1 MΩ) with reference to ground (GND terminal); voltage: +3.6 V
Pulse input compatibility: Flow Meters with class OA (reed output) and class OC (open-collector) pulse outputs
Max. frequency / Pulse min. duration: 5Hz – 100ms
Flow Meter installation position: Return (standard), configurable on the forward
Pulse rate: 1 – 2,5 – 10 – 25 – 100 – 250 – 1000 – 2500 litres/pulse
Heat carrier fluid: Water (standard), configurable for water and glycol solution
M-Bus communication interface: Compliant to EN 1434-3, with galvanic separation
M-Bus baud rate: 2400 baud (standard), also configurable to 300 or 9600 baud
Type of cable for M-Bus connection: Telephone cable J-Y(ST) Y2 x 2 x 0,8mm²
Local Bus interface: Compliant to EN 13757-6, 2400 baud, proprietary unidirectional protocol
Type of cable for Local Bus connection: Two wire cable (2 x 0.6mm² , max. length: 50m)
Billing recording: 12 fixed monthly recordings, two periods with programmable dates (DD/MM)
Anomaly/alarm recording: Circular log, four events (type of event and date)
Other recordings: Heat carrier fluid max. flow rate and max. power
Type of connections: Removable, 14-pole terminal block (5mm pitch)
Electric features
Power supply: Battery-operated
Battery rated voltage: 3,6V
Type of battery: Pre-wrapped package (2xAA – capacity: 4.8 Ah – spare part code: 1592269)
Battery life: 10 years operation + 1 year stock

Electric drip-feed oiler ELO 24V DC capacity 140ml
Material: Brass nickel-plated. Glass cylinder made from acrylic glass. Voltage: On choice: 230V AC, 50Hz, or 24V DC. Drip rate normal: about 45 drops per 1 ml. Other than the manual drip-feed oiler, which also drips when the machine has stopped, the electric drip-feed oiler only drips as long as the machine is running. When the machine stops, the electric drip-feed oiler is also automatically shut off, as the oiler is controlled via the machine programme. Finest dosing of drops is possible - by turning a knurled nut at the top part of the oiler. Almost all liquids can be dosed drop by drop, provided they are not mixed with solid matters. It is also suited for other media, provided they do not thicken with heat. Attention must be paid to the compatibility with acrylic glass and buna N used as sealing material. (possibly natural glass and vitone sealings on request). Duty cycle: intermittent 20%. Protection class acc. to EN 60529: IP20. Power consumption: 12VA (12W).
Article ID: 68033100

Swing bolt DIN 444 thread M20x63mm l1=130mm stainless steel
Material: Stainless steel 1.4305. Precision made, thread rolled. The thread lentgh is larger than DIN. The same size stainless steel version is not part of the DIN.
Article ID: 65499429

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 30 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Push-in L-fitting »Blue Series«, Self-locking, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Standard cylinder »SE« ISO 15552, double-acting, Piston Ø 32, Stroke 75, G 1/8, Working pressure 1 - 10 bar, Temp. -20°C to 70°C
These cylinders are ideal for a wide range of applications owing to their robust design and ecxellent value for money.
The standard type has a double-acting cylinder and features a magnetic piston as well as integrated cushioning.
The magnetic switches are mounted in T-slots on three sides of the body.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Pushbutton safety coupling I.D. 6, ISO 6150 C, Stainless steel, Sleeve I.D.6, Operating pressure max. 12 bar, Temp. -20°C to 200°C
High quality, robust and long-lifetime quick connect coupling in a safety design that can be operated with one hand.
When pushed for the first time the coupling is vented, the plug remains securely in the coupling.
After a second push the plug is released.
This prevents a potential "whiplash effect" and the risk of operating personnel is practically excluded.

The safety version meets ISO standard DIN EN ISO 4414.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive, mining, offshore.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0-1.6 bar/23 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Kamlok quick-connect plug with interior thread, A type, Aluminium, G 3/4, Plug Ø 32 mm, Pressure max. 16 bar, Temp. max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Quick relief valve »lineonline«, with silencer, Hose - hose, for hose Ø 4 mm, Operating pressure 1 - 10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.

Hex. coupl. nut G 1/8 sleeve size I.D. 4, I.D. 6 AF 14 nickel-plated br. Max. working pressure 25 bar Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Rubber-metal buffer MGH stainless steel diameter 20mm height 10mm bore 5,3mm (for screw M5)
Material: Elastomer: Rubber NBR, black, hardness 55º Shore A. Metal part: Stainless steel 1.4301.Hollow design. One side metal, with mounting bore for allen screw DIN 912.Due to the hollow design, these elements are particularly suitable as end stops. Also usable as elastic machine feet.The grade of rubber has perfect physical properties.Temperature resistant up to +100ºC (for short time +120°C).Other sizes, Shore hardnesses or elastomer types on request.* Permissible Pressure Load.
Article ID: 68921200

High performance V-belt XPB EPDM datum length 1860 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491860

Pneumatic shuttle valve

ASM2 General features
Aluminium alloy body.
Output connections with shockproof thermoplastic cable gland G 1/2” .
Nitrile rubber membrane, on request in teflon or other special materials.
Working temperature: -20 ÷ 70 °C.
Storage and transport ambient temperature: -25 ÷ 70°C.
Unit weight: 1,4 Kg.
Electric features
Commutation of two single-pole microswitches.
Rated insulation voltage Ui 380V~
Continuous duty rated current Ith  10A

Cylindrical bush slotted version 12 x 14 x 15 mm
Main characteristics Self lubricating and maintenance free, ready to install. Perfectly suited for lower sliding speeds. Low wear, low friction coefficient, no 'stick slip'. Perfectly suited for circular, swivelling and partly for axial movement. Can be used at extremely high bearing loads. No moisture absorption. High corrosion Construction Tin-plated steel back (incl. edges). Multi-porous bronze layer, sliding surface PTFE-lead-compound. Technical data Stat. surface pressure: max. 250 N/mm² Dyn. bearing load: max. 56 N/mm² Friction coefficient: 0.03 - 0.20 Sliding speed: max. 2 m/s Temperature range: -195°C to 280°C Therm. conductivity: 40 W/K*m Recommended mounting tolerances Housing bore H7, shaft tolerance up to 55 Ø f7 above 55 Ø h8

Article ID: 62401215

Chain tensioner SPANN-BOX® size 1 short low tensioning force 20 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040309

Spherical bearing DIN 12240-4-K type GD without outer ring maintenance-free bore 30mm outer diameter 55mm stainless steel
Material: Inner ring stainless steel 1.4034, hardened, ground and polished. Bearing shell stainless steel 1.4571, with PTFE-lining.Dimensions according to DIN 648 / 12240-1 series K (wide version). Maintenance-free.Suitable for high dynamic loads.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63399330

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 20 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Fork head, »Y« type (incl. thread adapter), for compact cylinder »ACP«, Piston Ø 16, Piston rod thread M4x0.7 i.
Fork model, »Y« type (incl. threaded adapter)

Push-in L-fitting, R 1/2 o., for hose exterior Ø 10 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Pushbutton safety coupling I.D.6, ISO 6150 C, Stainless steel, Sleeve I.D.13, Operating pressure max. 12 bar, Temp. -20°C to 200°C
High quality, robust and long-lifetime quick connect coupling in a safety design that can be operated with one hand.
When pushed for the first time the coupling is vented, the plug remains securely in the coupling.
After a second push the plug is released.
This prevents a potential "whiplash effect" and the risk of operating personnel is practically excluded.

The safety version meets ISO standard DIN EN ISO 4414.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive, mining, offshore.

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0-10 bar/145 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight push-in fitting »Blue Series«, G 1/2 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in T-fitting »click-clock«, rotating, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 15 mm, white, Operating temp. max. 90 °C, PN max. 12 bar
For fastening rigid PA or aluminium pipes to the wall.

High performance V-belt XPB EPDM datum length 1900 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491900

Pneumatic shuttle valve

Length : 800 mm
SVM-F-204x92-0800-B-F0E
SKU: SVMF040800
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

EV40 General features
Backlighting LCD display with graphic visualization of the system and its data.
6 buttons for selection.
3 LED for relays status indication.
DIN Container: 6 modules.
Disconnection type: 1B (micro-disconnection).
Pulse voltage: 4000V.
Software class: A.
Clock charge reserve: 5 years.
Probes measurement range: 0 ÷ 150°C (+/-1°C).
Electric features
Power supply: 230 Vac.
Consumption: 5VA.
Analog inputs: collector probe, boiler probe and integration probe NTC 1k-200°C (EC21).
2 optoisolated inputs.Output relays: 1 relay for collector circulation pump, 1 relay for integration pump or for deviation valve, 1 relay with programmable function.
Contacts rating: 5(3)A 230Vca.
Serial port RS232: for remote control with GSM modem (by means of SMS).

Cylindrical bush slotted version 14 x 16 x 10 mm
Main characteristics Self lubricating and maintenance free, ready to install. Perfectly suited for lower sliding speeds. Low wear, low friction coefficient, no 'stick slip'. Perfectly suited for circular, swivelling and partly for axial movement. Can be used at extremely high bearing loads. No moisture absorption. High corrosion Construction Tin-plated steel back (incl. edges). Multi-porous bronze layer, sliding surface PTFE-lead-compound. Technical data Stat. surface pressure: max. 250 N/mm² Dyn. bearing load: max. 56 N/mm² Friction coefficient: 0.03 - 0.20 Sliding speed: max. 2 m/s Temperature range: -195°C to 280°C Therm. conductivity: 40 W/K*m Recommended mounting tolerances Housing bore H7, shaft tolerance up to 55 Ø f7 above 55 Ø h8

Article ID: 62401410

Chain tensioner SPANN-BOX® size 1 short high tensioning force 20 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040409

Precision worm wheel centre distance 40mm i=75 75 teeth
Material: Special brass CuZn40Al2/So. Pressure angle 15°. Attention: Keyway not according to DIN. The gear wheels can only be used with worms having the same centre distance and the same transmission. Can be built into gear systems, no reworking required, thus short assembly times. * Worm only polished - worm gear with helical gearing. ** The figures stated for the efficiency are only reference values, since - besides the lead angle - also mounting, lubrication, speed and assembly have an influence on the efficiency.

Article ID: 32237500

Compact cylinder »ACP«, double-acting, Piston Ø 80, Stroke 85, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Fork head, »Y« type (incl. thread adapter), for short stroke cylinder »ACQ« and »ASQ«, Piston Ø 16, Piston rod thread M4x0.7 i.
Fork model, »Y« type (incl. threaded adapter)

Ball valve EN 331 DVGW, nickel-plated brass, Hand lever, IT/IT, Rp 1 1/4, DN 32, Operat. temp. -15°C to 60°C, PN max. 5 bar (Gas)
Ball valves with full bore, for gas installations. Applications: Natural gas, LPG, town gas

Bulkhead elbow connector, Pipe exterior Ø 22 mm, PN max. 160 bar, a/f1 36, a/f2 41, a/f3 27, galvanised steel
Bulkhead elbow connector, light type

Standard pressure gauge »pressure line« Connection radial bottom, G 1/8, Goods class 2.5, Measurement range 0-16 bar/235 psi, Ø 40
Low-priced series of standard pressure gauges available in all popular diameters with the most frequently requested measuring ranges.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Straight push-in connector »Blue Series«, reducing, for hose exterior Ø 10/6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »Blue Series«, G 1/2 i., for hose exterior Ø 14 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 18 mm, white, Operating temp. max. 90 °C, PN max. 12 bar
For fastening rigid PA or aluminium pipes to the wall.

High performance V-belt XPB EPDM datum length 1950 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491950

Pneumatic shuttle valve

Size : 200 mm
SMR-N-0200x200x40-04E-S6-S
SKU: SEMR202038
Stock: 10
Magnet quality: Neodymium GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C
No of bars: 4
Weight: 4.1 kg
Magnetic grids - also called magnetic grates - are often placed at a pouring point or receiving hopper. They filter very fine magnetic and even weakly magnetic ferrous contaminants from free-flowing powders and granulates.Often used for control purposes.Manual quick-cleaning by extractor.

Optimal magnet contact
Low overall height
Capture Fe particles from 30 µm
Max. particle size 10 mm
With neodymium magnetic bars

Application

In pouring points, hoppers, as inspection before bagging, etc.

Magnetic grids filter very fine magnetic and weakly magnetic ferromagnetic contaminations from free-flowing powders and granulates. Often used for control purposes. Manual cleaning (quick cleaning).
 
They are used for applications in the plastics, food, pharmaceutical, ceramics and other industries. In the hopper of your injection moulding machine, for protection of your installation or as final inspection of your product, e.g. just prior to bagging.
 
Magnetic grids consist of several very powerful Neoflux® (neodymium) magnetic bars. These are located in the middle of your product flow and therefore even capture the smallest ferrous particles, down to 30 microns. Even stainless steel scrapings are captured. These particles are so small that they cannot even be detected by a metal detector.
 
An effective use is to place two magnetic grids in a cascade configuration, so the product flowing past them must contact the magnetic bars or at least pass extremely close to them. We also use this method with our Cleanflow magnets (grids in housing).

Design

Construction & materials data

Goudsmit magnetic grids are available in square and round.
 
The neodymium magnetic bars are provided with enveloping extractor tubes. This makes the grate robust and manual wiping unnecessary. By pulling the magnetic bar unit from the extractor tubes, the captured ferrous contaminants will fall off automatically. We call this 'manual quick-cleaning'.
 
The extractor tubes also serve to protect the magnetic bars, making them last longer.
 

Magnet quality: neodymium N-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (8,000 gauss on tube Ø25)
Materials - in contact with product: AISI304 (RVS 1.4301) / AISI316 (SS 1.4401)


Iron discharging / cleaning

Filtering & discharging of ferrous contaminants

The procedure for discharging the filtered ferrous particles is as follows:

stop the product flow
remove the entire grid from the product chute or hopper and place it on a pre-cleaned, non-magnetic surface (e.g. wood, aluminium or stainless steel)
remove the retainer for the two grid parts
pull the magnetic bars unit out of the extractor housing
the captured metal particles now fall off the extractor tubes. Make sure you keep the magnet bars away from these magnetic metals during this procedure.
lay the part with the magnetic bars on another well-cleaned surface
now make sure you also place the magnetic bars far enough away from the magnetic particles.
dispose of the metal contaminants
if necessary: clean all the grid parts with a dry cloth and/or suitable stainless steel cleaning fluid
mount the two grid parts and the retainer
place the grid back in the product chute or hopper
restart the product flow.

ZL30 General features
Controlled fluid: cold and hot water with max 50% glycol volume, superheated water and steam.
Fluid temperature controlled 5 ÷ 120 ° C.
High closing point (▲).
Stainless steel shutter.
Stem in stainless steel.
EPDM O-ring stem seal.
Flow rate characteristic: regulation port A – AB: equal percentage (VDI / VDE 2173) n (gl) = 3; bypass B – AB: linear (VDI / VDE 2173).
Leakage rate: regulation port A – AB: max 0.05% of Kvs; bypass B – AB: max. 1% of Kvs value.
External thread in accordance with ISO 228.
Red Rg5 stamped brass valve
Nominal pressure 1600 kPa.
Differential pressure Δpmax 400 kPa.

Cylindrical bush slotted version 15 x 17 x 10 mm
Main characteristics Self lubricating and maintenance free, ready to install. Perfectly suited for lower sliding speeds. Low wear, low friction coefficient, no 'stick slip'. Perfectly suited for circular, swivelling and partly for axial movement. Can be used at extremely high bearing loads. No moisture absorption. High corrosion Construction Tin-plated steel back (incl. edges). Multi-porous bronze layer, sliding surface PTFE-lead-compound. Technical data Stat. surface pressure: max. 250 N/mm² Dyn. bearing load: max. 56 N/mm² Friction coefficient: 0.03 - 0.20 Sliding speed: max. 2 m/s Temperature range: -195°C to 280°C Therm. conductivity: 40 W/K*m Recommended mounting tolerances Housing bore H7, shaft tolerance up to 55 Ø f7 above 55 Ø h8

Article ID: 62401510

Chain tensioner SPANN-BOX® size 1 short low tensioning force 06 B-2
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040321