Straight screw-in fitting, G 1/6 o., for hose 4/8 mm, AF 17, Working pressure max. 10 bar (20 °C)/max. 1 bar (170 °C), PFA
Perfluoroalkoxy alkane (PFA): A fluoroplastic with the same chemical resistance as PTFE but much stronger and suitable for temperatures up to 200°C.

Male elbow, M12x1.5 tapered o., Pipe exterior Ø 8 mm, PN max. 315 bar, a/f1 17, a/f2 12, galvanised steel

Straight fitting, Pipe exterior Ø 8 mm, PN bar 630, A/F1 19, A/F2 17, galvanised steel
Union, heavy type

Replacement diaphragm for pressure regulator, »FUTURA-mini«, Size 0, G 1/4

Angled screw-in supports, R 3/8 o., for hose I.D. 12 mm, AF 10, Over-pressure max. 17 bar, Temperature range -40 °C to 90 °C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

High performance V-belt XPB EPDM datum length 1150 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491150

Frequency:50 Hz
Speed:2965 1/min
Shaft Output:29568 W
Volume Flow:3222 m³/h
Pressure:Δp s20115 Pa
Pressure:Δp t20835 Pa
Density:43862 kg/m³
Sound Pressure:106 dB(A)

Length : 600 mm
SVM-F-204x92-0600-B-F0E
SKU: SVMF040600
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ECC15GSA- ECC20GSA General features
Temperature up to 120°C (it resists up to 150°C).
Nominal pressure: PN16.
Protection degree: IP68.
Dry clockwork with magnetic transmission.
Rotatable register at 360° for an easier reading.
High resistance components against wear and corrosion.
Nonmagnetic capsule for protection against external influences.
REED connecting cable (2 x 0,5 mm² x 1,5 m), not extendable, resistant up to 130°C.
Impulse values rigidly confirming to MID directive.
10 litres/pulse.
Standard measuring range with horizontal installation Qi/Qp 1:50.
Standard measuring range with vertical installation Qi/Qp 1:25.
Clockwork maximum reading: 99999 m³.
Clockwork minimum reading: 00001 m³.

Shaft collar DIN 705 A set screw with slot bore 8mm black finishing
Light-duty series. With set screw DIN EN 27 434 made from steel with black oxide finish. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62389008

Sliding hub with elastic coupling type RNR, size 0
Material: Material: Sliding hub: steel, zinc-plated and chromated yellow, asbestos-free and rustproof friction pads. Elastic coupling: coupling hubs cast iron, insert (toothed ring) Polyurethane. Hardness 92° Shore (optional 98° Shore). The slipping torque can be adjusted with common assembly tools for screws. The elastic coupling can be mounted in axial direction. Torque can be altered after mounting. By mounting a second disc spring, the torque range can be doubled (second spring has to be ordered separately). Customized bores and feather-key grooves available at extra charge. 1) above Ø 19 mm with flat keyway DIN 6885/3. * Essential for dimensioning. ** Nominal torque of the elastic coupling. *** Maximum torque of the elastic coupling.

Article ID: 61220000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 15 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Seal set (wear part), for standard cylinder, Piston Ø 40, NBR seal
Set of gasket (parts subject to wear)

Short stroke cylinder, double-acting, Magnet, Piston Ø 25, Stroke 25, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Articulated male hinge model, ISO 15552, ISO 21287, Ø50, with 4 screws
Articulated male hinge model

Male elbow, M18x1.5 tapered o., Pipe exterior Ø 15 mm, PN max. 315 bar, a/f1 27, a/f2 19, galvanised steel

Straight fitting, Pipe exterior Ø 14 mm, PN bar 630, A/F1 27, A/F2 24, galvanised steel
Union, heavy type

Double threaded nipple, G 1/8 o., G 1/8 o., Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Straight screw-in fitting »value line«, G 1/8 o., for hose exterior Ø 4 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 32 teeth tooth width 20mm outside diameter 68mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195032

High performance V-belt XPB EPDM datum length 1250 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491250

Frequency:50 Hz
Speed:2970 1/min
Shaft Output:35115 W
Volume Flow:3812 m³/h
Pressure:Δp s20454 Pa
Pressure:Δp t21265 Pa
Density:43862 kg/m³
Sound Pressure:107 dB(A)

AD52 General features
Operation with magnetic action ( by repulsion with permanently opposed magnets)
Suitable for liquids with specific weight from 0.9 to 1.1 kg/ dm3
Threaded connection male G 1 ¼ , 36 mm spanner
Shock- proof thermoplastic case with self-retaining screws
Non- toxic thermoplastic resin float Ø38×70, on request with stainless steel float up to 110° C
Choice between two fixed level differentials
Brass body
Compliance with the standards CEI EN 60947- 5- 1
Electric features
SPDT microswitch.
Electrical connection with 6,35 Faston (supplied).

SL-retainer steel zinc plated size 14 for bolt diameter 14mm
Material: Spring steel, zinc plated.SL retainers are used to fix parts on shafts or bolts in axial direction. The large curvature results to a strong preload and eleminates tolerances for a snug fit. They are not so easy and quick to mount and to dismount like KL retainers, but the connection is much better secured against unwanted loosening.* Max. transmittable force, static, on shafts with min. strength 500 N/mm².
Article ID: 63791301

Internal gear made of steel C45 module 1.5 70 teeth tooth width 15mm outside diameter 135mm
Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.

Article ID: 22847000

Precision spur gear made of steel 16MnCr5 module 1.5 40 teeth bore 12mm hardened and ground outside diameter 63mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 22884000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 14 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Threaded connection G 1/2, for service unit »ONE«

Quick-connect coupling I.D. 2.7, Stainless steel 1.4305, G 1/8 ET, Operating pressure 0 - 35 bar, Temp. -20 °C to 200 °C
One-hand quick disconnect couplings, one side sealing, extremely compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology, offshore.

Seal set (wear part), for standard cylinder, Piston Ø 100, NBR seal
Set of gasket (parts subject to wear)

Pipe double nipple, R 1/4, Length 40 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Double threaded nipple, G 3/8 o. left, G 3/8 o. left, AF 19, Brass, Max. working pressure 25 bar, Max. operating temperature 150°C

Push-in T-connector »click-clock«, for hose exterior Ø 14 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 80 °C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

1-ear hose clamp with insert ring, Stainless steel 1.4301 (W4), Clamping range 17.0 - 19.3 mm, Belt width 9.8 mm

High performance V-belt XPB EPDM datum length 1260 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491260

Frequency:50 Hz
Speed:2960 1/min
Shaft Output:34768 W
Volume Flow:3799 m³/h
Pressure:Δp s20316 Pa
Pressure:Δp t21122 Pa
Density:43862 kg/m³
Sound Pressure:107 dB(A)

Length : 200 mm
SVM-N-204x55-0200-B-F1M
SKU: SVMN020200
Stock: 4
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

SL-retainer steel zinc plated size 16 for bolt diameter 16mm
Material: Spring steel, zinc plated.SL retainers are used to fix parts on shafts or bolts in axial direction. The large curvature results to a strong preload and eleminates tolerances for a snug fit. They are not so easy and quick to mount and to dismount like KL retainers, but the connection is much better secured against unwanted loosening.* Max. transmittable force, static, on shafts with min. strength 500 N/mm².
Article ID: 63791501

Profile damper TS 82-44 diameter 82mm thread M16
Material: Co-Polyester Elastomer. The profile dampers TS are a maintenance-free, self-contained damping elements. Due to the almost linear damping characteristics it provides very smooth energy absorption along with minimum reaction loads on the machine. The excellent temperature characteristic of the material provides consistent damping performance over a temperature range of -40°C to +90°C. The low installed weight, the economic price and the long operating life of up to 1 million cycles makes this an attractive alternative to hydraulic end position damping, if the moving mass does not need to stop in an exact datum position and it is not necessary to absorb 100% of the incoming energy. The life cycle is up to 20 times longer than for urethene dampers and up to ten times longer than for rubber springs. Environment: Resistant to oil, grease seawater and to microbe or chemical attack. Excellent UV and ozone resistance. Material does not absorb water or swell. Dynamic Force Range: 533 N to 23,500 N. Temperature Range: -40°C to +90°C. Energy Absorption: 35% to 64%. Material Hardness: Shore 40D. Mounting: in any position. Impact Velocity range: up to max. 5 m/s. Mounting Bolt Torque: M4: 2 Nm. M5: 4 Nm. M6: 6 Nm. M12: 50 Nm. M16: 120 Nm. On request: special strokes, characteristics, spring rates, sizes and materials. Download Energy-Stroke Characteristics 1.5 MB   1) Max. energy capacity per cycle for continuous use. 2) For a single cycle, e.g. an emergency stop.
Article ID: 69118200

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 19.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Unidirectional flow control valve »lineonline«, Flow one-sided, Thread - hose, G 1/8, for hose Ø 8, Operating pressure max. 10 bar
Control the air intake and thus the speed of pneumatic units.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 32, Stroke 50, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Male hinge model, ISO 15552, ISO 21287, Ø100, with 4 screws
Male hinge model

Plug-in connector for coupling I.D. 12, Bright brass, Sleeve I.D. 16, Pressure max. 16 bar, Medium / ambient temp. -10°C to 50°C

Silencer nozzle for reducing noise, for direct mounting on the thread of the blowgun, for use in tight spaces

Wear part set, consisting of: Diaphragm complete, Valve cone assembly and O-ring, for pressure regulator »Standard-mini«

Plug for bite-type tube fitting, Pipe exterior Ø 10 mm, PN max. 315 bar
Plug, light type

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 3 25 teeth tooth width 30mm outside diameter 81mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305.

Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range
-60°C to +120°C, short periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23395025

High performance V-belt XPB EPDM datum length 1320 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPB are a useful substitute for SPB and 17.
Width b = 16.3 mm.

Height h = 13 mm.

Smallest medium pulley diametre = 112 mm.

Weight per Metre 0.183 kg.

Article ID: 15491320

Frequency:50 Hz
Speed:2760 1/min
Shaft Output:22 W
Volume Flow:109 m³/h
Pressure:Δp s193 Pa
Pressure:Δp t226 Pa
Density:43862 kg/m³
Sound Pressure:64 dB(A)

Safety handwheel SHR material aluminium diameter 140mm
Material: Aluminium, polished. Coupling attachment assembled. Can only be supplied with revolving, cylindrical handle made from plastic with threaded steel bolt and with hub keyway. According to safety regulations, handwheels must be mounted on the shaft in such a way that they do not rotate along with the machine drive. Safety handwheels comply with this regulation. Procedure: Wheel disengaged if not used. By axial displacement of the wheel (pulling) the two serrated wheel rims are engaged. The wheel is now positively keyed to the shaft. When the wheel is released, it automatically disengages. The coupling elements are assembled together in an enclosed unit. Coupling attachment made from steel, nitrided, bearing surface ground and PTFE coated, for minimal friction between bearing surfaces and high wear resistance. An oil hole is provided, which serves to connected to a pressure oiler in the wheel hub. Frequent lubrication is an important precondition in guaranteeing the correct functioning of the plain-bearing coupling attachment. The range of application of these handwheels is limited to low shaft speeds, or to higher speeds of only short duration (e.g. feed screws for milling machine table with rapid feed). The coupling attachments can also be supplied separately, to be mounted with existing handwheels. Prices on request. We assume no liability for any consequential damage.

Article ID: 67061400

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 1/2, AF 27, Trigger pressure 12.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Unidirectional flow control valve »lineonline«, Flow one-sided, Hose - thread, G 1/8, for hose Ø 8, Operating pressure max. 10 bar
Control the air intake and thus the speed of pneumatic units.

Pushbutton safety coupling I.D. 11, ISO 6150 C, Stainless steel, G 3/8 ET, Operating pressure max. 16 bar, Temp. -20 °C to 200 °C
High quality, robust and long-lifetime quick connect coupling in a safety design that can be operated with one hand.
When pushed for the first time the coupling is vented, the plug remains securely in the coupling.
After a second push the plug is released.
This prevents a potential "whiplash effect" and the risk of operating personnel is practically excluded.

The safety version meets ISO standard DIN EN ISO 4414.

These safety couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, manufacturing industry, mining, offshore.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 8, Stroke 10, M5x0,8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 2, Length 60 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Connection nipple for flat suction cup, round »PFG« type, G 1/4 ET, for suction cup diameter 60 - 80 mm, Connection M10x1.25
Connection nipples for flat suction pads

Throttle check valve »Blue Series«, Discharge throttle, G 1/4 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Plug for bite-type tube fitting, Pipe exterior Ø 18 mm, PN max. 315 bar
Plug, light type