L-multi-distributor »Blue Series«, 4-fold, rotating, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Filter »GA« metal container, Viewing tube, Mounting bracket, 5 µm, Size 600, G3/4, Input pres. max 10 bar, Working pres. 1.5-9 bar
Centrifugal separators with a sintered filter element.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 4.3x3, PN at 20 °C max. 19 bar, blue, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Bulkhead fitting »value line«, M28x1.5 o., G 1/2 i., Operating pressure max 60 bar, Operating temp. max 150°C, nickel-plated brass
For air, water, steam, oil, etc.

Push-in L-fitting »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Cable tie, PA 6.6, black, Band: 4.8 x 200 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.

Pipe double nipple 23, ET/ET, Black steel, R 3/4, Length 100.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

High performance V-belt XPA EPDM datum length 2207 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292207

Frequency:50 Hz
Speed:2955 1/min
Shaft Output:9380 W
Volume Flow:1645 m³/h
Pressure:Δp s11991 Pa
Pressure:Δp t12514 Pa
Density:43862 kg/m³
Sound Pressure:99 dB(A)

Intellitouch CH193MB General features
Protection degree: IP20
ON / OFF boiler control (settable from the main menu)
Acoustic signals: buzzer feedback with key pressing
Perpetual clock calendar, with backup battery
Software Class A.
Minimum differential: ±0,1K.
Thermal gradient: 4K/h.
Maximum ambient temperature: 45 °C
Electric features
Power supply from MiA bus
Insulation class: II
Pollution degree: 2

Neoprene timing belt 40 MXL 012 50 teeth Lw 101.60mm belt width 3.2mm
Material: Neoprene with glas-fibre tensile member. Teeth surface fabric-coated. Timing belt with inch dimensions, classical shape with trapezoid teeth. Profile MXL = 0,08" = 2.032 mm. Belt width 012 = 3.2mm. Temperature range -20º to +100ºC.
Article ID: 18160400

SKF spherical roller bearing 22210 E/C3 double row inner diameter 50mm outer diameter 90mm width 23mm clearance C3
Material: Bearing steel.Spherical roller bearings in premium-quality.- For very high radial load and common high axial load in both directions.- Usable at angular displacement.- Usable for high speed, with groove and 3 lubribation holes.Temperature range: -30°C to +150°C (for short time up to +200°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64776328

Neoprene timing belt HTD 8M width 50mm Lw 2000mm 250 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17554400

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 3/8, Control range 0.2 - 4 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Push-in T-fitting »click-clock«, rotating, G 3/8 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Filter »G« PC container, Protective cage, Mounting bracket, 5 µm, Size 300, G 1/4, Input pres. max 10 bar, Working pres. 1.5-9 bar
Centrifugal separators with a sintered filter element.

Push-in L-fitting, R 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

1/3 Tube fitting, G 1 1/4 x 25 mm, with NBR O-ring, with collar, Brass with a bare metal surface

Screw-in fitting, Aluminium / plastic, for PVC pneumatic hose 11.6x9, G 3/8, Temperature -15 °C to 70 °C, PN -0.95 - 15 bar

Cable tie, PA 6.6, natural, Band: 4.8 x 200 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.

Pipe double nipple 23, ET/ET, Black steel, R 1, Length 40.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

High performance V-belt XPA EPDM datum length 2282 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292282

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:9395 W
Volume Flow:1672 m³/h
Pressure:Δp s11821 Pa
Pressure:Δp t12360 Pa
Pressure:43862 kg/m³
Sound Pressure:99 dB(A
Protection Type:55
Weight:ca. 330,0 kg
AC:-
Three-Phase:+
Universal Voltage:50Hz-
:60Hz-
Explosion Protection:II 2G Ex h IIB T3 Gb

Length : 400 mm
SVM-N-114x34-0400-B-F1M
SKU: SVMN060400
Stock *: 0
Advised max. installation height: 65-80 mm
Height: 34 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ZD..NA General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Spur gear made of polyketone die-cast with hub module 0.5 35 teeth tooth width 3mm outside diameter 18,5mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28103501

Double shaft block GWD-1 ISO series 1 for shaft diameter 30mm
Material: Extruded aluminium. Matching quadro linear-bearing units KGQ-1 of the ISO Series 1. Shaft blocks are practical and robust machine elements, that provide a simple way of attaching the guiding shaft of the linear bearings on the respective machine parts. They allow true to size and, most important, cost efficient constructions. *For cylindrical screws with Allen screw according to DIN 912 or ISO 4762.

Article ID: 64640230

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 3/8, Control range 0.5 - 8 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Closing coupling DN 9, Brass 2.0401, Length 37 mm, Operating pressure max. 15 bar, Medium / ambient temperature -20 °C to 160 °C
Compatible with HASCO Z 8 system.

For temperature control applications involving hot or cold water or heat transfer oil.
Optionally with free passage, one or both sides sealing.
Female-threaded couplings and plugs with female-threaded PTFE seal.

Filter »G« PC container, Protective cage, Mounting bracket, 5 µm, Size 300, G 1/2, Input pres. max 10 bar, Working pres. 1.5-9 bar
Centrifugal separators with a sintered filter element.

Check valve, Lightweight construction, Stainless steel 1.4301, Operating temperature -20 °C to 150 °C, G 1/2, PN max. 16 bar
Stainless steel check valve with full bore and very low opening pressure, no maintenance required.
Applications: Compressed air, water, neutral gases, gaseous and liquid non-corrosive media, oils.

1/3 Tube fitting, G 1 x 22 mm, taper seat, with collar, CH type, Brass with a bare metal surface

Push-in L-fitting »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

3/3 Stand pipe fitting, G 3/4 ET x 19 mm, nut 1, taper seat, lightweight type, Brass with a bare metal surface

Pipe double nipple 23, ET/ET, Black steel, R 1, Length 60.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 40 teeth tooth width 20mm outside diameter 84mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195040

High performance V-belt XPA EPDM datum length 2332 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292332

Frequency:50 Hz
Speed:2955 1/min
Shaft Output:17838 W
Volume Flow:3832 m³/h
Pressure:Δp s10948 Pa
Pressure:Δp t12187 Pa
Density:43862 kg/m³
Sound Pressure:100 dB(A)

Length : 210 mm
SVM-N-158x32-0150-F-F1M
SKU: SVMN030150
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Spur gear made of polyketone die-cast with hub module 0.7 16 teeth tooth width 6mm outside diameter 12,6mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28201601

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 3/8, Control range 0.5-10 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Series base plate 2-fold, M5 for mini solenoid valve 15 mm

3/2-way solenoid valve, direct mounting, Banjo connection, NC, 230/50 V, Medium/ambient temp. -10 °C to 60 °C, G 1/8 ET, PN 10 bar
Compact solenoid valves for mounting directly on the actuator
(single-acting cylinder, valve, etc.).

- Optimum installation
Supply port (1), solenoid valve body, coil and cable socket can be rotated 360°
- Manual operator
- Exhaust air restrictor available on request

Round cylinder TP (ISO 6432) double-acting, Piston Ø 16, Stroke 10, M5, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

3/3 Stand pipe fitting, G 1/2 IT x 13 mm, nut 3/4, taper seat, CH type, Brass with a bare metal surface

Straight push-in fitting »Blue Series«, round, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in fitting, R 1/2 o., Pipe exterior Ø 16 mm, PN bar 400, A/F1 30, A/F2 27, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, heavy type

Straight push-in fitting »Blue Series«, round, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 1.5 45 teeth tooth width 17mm outside diameter 70.5mm
Material: Outer part: Plastic
PA 12 G. Steel core: Stainless steel 1.4305.

Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range
-60°C to +120°C, short periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 21895045

Clamping bush MSA bore 28mm
Material: Steel.

Mechanical, all-steel clamping elements, containing no hydraulic pressure medium. Both inner part (1) and outer part (2) have a cylindrical buttress thread with a lengthwise slot. The inner ring (3) connected to the inner part (4) has threaded studs, that create a tensioning effect when tightened.The bushes are designed for very high loads in radial as well as in axial direction. The axial runout does usually not exceed 0,02 mm. If a clamping bush without slot on the outside part is to be welded onto a workpiece, we would ask you to contact us first. Feather key grooves in the shaft do not cause any problems; simply remove the frictional corrosion.

Tolerance: Shaft h11 up to k6, Hub H7 up to H11

The values for the maximum transmittable torque and the maximum permissible axial force for the clamping bush at static load are stated in the table above. With dynamic load these values have to be reduced, i.e. divided by the operating factors listed in the adjoining table.

Operating factor: See PDF-catalog page.

1) approximate surface pressure between clamping bush and hub.


Article ID: 61502800

High performance V-belt XPA EPDM datum length 2360 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292360

Frequency:50 Hz
Speed:2955 1/min
Shaft Output:7737 W
Volume Flow:1247 m³/h
Pressure:Δp s11081 Pa
Pressure:Δp t11834 Pa
Density:43862 kg/m³
Sound Pressure:98 dB(A)

Neodymium 1000 mm
HRA-N-103x22-AA-1000-B-W
SKU: TGAA100043
Stock *: 0
Width: 103 mm
Height: 22 mm
Water-resistant: yes
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

OT.. General features
Asynchronous single-phase tubular motor.
Operation with switch, button or radio using the form OCR1.
Electromechanical stroke end.
2 adjustable stroke end points.
Stroke adjustment via adjustment cams.
Exit pin with spline shaft.
Continuous operating time 4 min
Electric features
Power supply: 230V 50Hz
Type of cable: H05VVF white
Cable length: 2,5 meters
Conductor: 4×0,75 mm2

Flanged bush BBP bore 6mm polyamide 6.6 outer diameter 10mm length 8mm flange diameter 15mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62380600

Linear bearing unit KG-3 ISO series 3 Economy-Line with self-aligning linear ball bearing with seals for shaft Ø 20mm
Material: Material: Housing made from extruded aluminium with a closed linear bearing of the ISO Series 3 from reliable brand in good quality at low price. Self-aligning capability that accommodates tilting. All bearings are lubricated ready-to-install. Recommended shaft tolerance h6.
Article ID: 64672002

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 3/8, Control range 0.5-16 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Bi-metallic thermometer for heating, Connection rear, G 1/2, Immersion shaft length 100 mm, Ø 80 mm, Display range 0 °C to 60 °C
Applications: Heating, plumbing, universal.

3/2-way solenoid valve for direct mounting, Banjo connection, NC, 24 DC, Medium/ambient temp. -10 °C to 60 °C, G 1/8 ET, PN 10 bar
Compact solenoid valves for mounting directly on the actuator
(single-acting cylinder, valve, etc.).

- Optimum installation
Supply port (1), solenoid valve body, coil and cable socket can be rotated 360°
- Manual operator
- Exhaust air restrictor available on request