ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Neoprene timing belt HTD 8M width 50mm Lw 1440mm 180 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17553400

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 80, Stroke 35, G 3/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Sensor, »CS1« type, for round cylinder series »MI« and »MSI«, Piston Ø 16, REED sensor, 2-wire, M8 plug, 150 mm cable, NO
Sensors, »CS1« type

3/2-way valve, electropneumatic, »3V«, monostable, NO, G 1/4, 230 V, 50 Hz, Operating pressure 1.5 - 8 bar, Temp. -20 °C to 70 °C
3/2-way pilot valves
- Electro-pneumatic -

Safety coupling I.D. 7.6, Steel / brass galv., Sleeve I.D. 9, Operating pressure max. 16 bar, Med./ambient temp. -20 °C to 100 °C
High-quality, robust and durable, one-hand quick disconnect safety couplings, with very high flow rates and only a small pressure drop.

The coupling is released fully automatically in two steps. Air is relieved from the coupling before it is completely disconnected. The plug is only disconnected from the coupling if the residual pressure has dropped below 0.3 bar. The dreaded "whiplash effect" is thus avoided and the risk of injury virtually eliminated.

This safety version conforms to ISO-Standard DIN EN ISO 4414.

These safety couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, manufacturing industry, workshops, automotive, mining.

Throttle check valve »Blue Series«, Discharge throttle, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pipe double nipple 23, ET/ET, Black steel, R 1/4, Length 200.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Ball valve, Butterfly handle, Basic design, IT/ET, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 1/4, PN max. 50 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Rem. double threaded nipple, con. seal.R 1/4 o., R 3/8 o.nickel-plated brass, Max. working pressure 25 bar, Max. oper. temp. 150°C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

One-piece clamp coupling MAS both sides bore 25mm with keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. Feather Key Groove DIN 6885/1, Tolerance P9. The torques in
the table are maximum values which can only be achieved with perfect
mounting and dimensional accuracy of the shaft.

Article ID: 60099725

High performance V-belt XPA EPDM datum length 2000 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292000

Rubber buffer GH ø 15mm height 10mm with through hole 6,5mm
Material: Natural rubber hardness 55º Shore A.

Simple, reasonably priced standard components used for elastic mounting.

The grade of rubber used has perfect physical
properties.

Article ID: 68571510

Frequency:50 Hz
Speed:2930 1/min
Shaft Output:4326 W
Volume Flow:938 m³/h
Pressure:Δp s8286 Pa
Pressure:Δp t9017 Pa
Density:43862 kg/m³
Sound Pressure:94 dB(A)

B11AN General features
Elements in contact with the fluid are in stainless steel, laser welded.
Metallic frame.
Cover in shockproof thermoplastic material.
Output connections with PVC cable gland.
Connection G 1/4.
Maximum temperature of the controlled fluid: 120 °C.
Pressure switch body admissible temperature: -35 ÷ 60°C.
Storage and transport temperature: -35 ÷ 60 °C.
Unit weight: 0,47 Kg.
Electric features
Rated insulation voltage Ui 415V~
Continuous duty rated current Ith 16A

Elastic coupling RNH with half shell clamps backlash-free size 24 prebore 5mm (no H7) outer diameter 55mm overall length 78mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60552405

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.1 - 1 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Sensor, »CS1« type, for round cylinder series »MI« and »MSI«, Piston Ø 20, REED sensor, 2-wire, M8 plug, 150 mm cable, NO
Sensors, »CS1« type

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 40, Stroke 10, G 1/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Safety coupling I.D. 7.6, Steel / brass galv., G 1/2 IT, Operating pressure max. 16 bar, Med./ambient temp. -20 °C to 100 °C
High-quality, robust and durable, one-hand quick disconnect safety couplings, with very high flow rates and only a small pressure drop.

The coupling is released fully automatically in two steps. Air is relieved from the coupling before it is completely disconnected. The plug is only disconnected from the coupling if the residual pressure has dropped below 0.3 bar. The dreaded "whiplash effect" is thus avoided and the risk of injury virtually eliminated.

This safety version conforms to ISO-Standard DIN EN ISO 4414.

These safety couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, manufacturing industry, workshops, automotive, mining.

Throttle check valve »Blue Series«, Supply air throttle, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Ball valve, Manual lever, Basic design, IT/ET, nickel-plated brass, Operating temp. -20 °C to 150 °C, G 1/4, DN 8, PN max. 50 bar
Applications: Compressed air, water, non-toxic and non-corrosive gases, heating systems and air conditioning systems.

Push-in T-fitting »Blue Series« mini, rotating, G 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Two-piece clamp coupling MAT both sides bore 25mm without keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. The torques in the table are maximum values which can only be
achieved with perfect mounting and dimensional accuracy of the shaft.

Article ID: 60099825

Spur gear made of polyacetal resin die-cast with hub module 0.7 21 teeth tooth width 6mm outside diameter 16.1mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28202100

High performance V-belt XPA EPDM datum length 2032 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292032

Frequency:50 Hz
Speed:2960 1/min
Shaft Output:14534 W
Volume Flow:2985 m³/h
Pressure:Δp s9268 Pa
Pressure:Δp t10309 Pa
Density:43862 kg/m³
Sound Pressure:100 dB(A)

Length : 500 mm
SVM-F-204x92-0500-B-F0E
SKU: SVMF040500
Stock *: 0
Advised max. installation height: 70-110 mm
Height: 92 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Neoprene timing belt HTD 8M width 50mm Lw 1600mm 200 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17553700

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.1 - 2 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Sensor, »CS1« type, for round cylinder series »MI« and »MSI«, Piston Ø 25, REED sensor, 2-wire, M8 plug, 150 mm cable, NO
Sensors, »CS1« type

Spiral hose coupling set I.D. 7.6, PUR, Medium / ambient temperature -20 °C to 60 °C, Hose Ø 10x6.5, PN max. 10 bar, Length 4 m
Spiral or straight polyurethane hose, completely assembled with DN 7.6 safety coupling and steel plugs.

Coupling
Safety coupling made of steel / nickel-plated brass for high flow rates, specially designed for all applications susceptible to severe mechanical wear.
Strong, impact and vibration-resistant design for demanding environments.

Polyurethane hose
Extremely flexible spiral hose with excellent kink resistance and insensitive to dirt.
Combines high tear, tensile and impact strength with a long service life and optimal ageing qualities.
This hose is additionally characterised by outstanding resistance to abrasion and resistance to UV.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 4.3x3, PN at 20 °C max. 19 bar, black, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Throttle check valve »Blue Series«, Supply air throttle, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Flat suction cup, round, Material NBR, »PFG«, ø:40 suitable connection nipple IT G 1/8, suitable connection nipple ET G 1/8
Robust and hard-wearing suction pad with a single sealing lip.
Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to handle smooth or slightly rough surfaces. Due to its flat shape, it can grip the workpiece in a very short time and withstand the forces that result from fast movement of the object during handling. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very short evacuation timesSuitable for high lateral forcesGood intrinsic stability when attached to the loadSupports on the bottomVery short cycle timesHigh suction forces with small dimensions

Applications:
Handling workpieces with smooth or slightly rough surfaces, e.g. metal sheets,
cardboard boxes, sheets of glass, plastic parts and sheets of wood.

Elbow 41, 45°, IT/IT, Rp 1 1/4, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in T-fitting »Blue Series« mini, L-shape, rotating, G 1/8, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Two-piece clamp coupling MAT both sides bore 25mm with keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. Feather Key Groove DIN 6885/1, Tolerance P9. The torques in
the table are maximum values which can only be achieved with perfect
mounting and dimensional accuracy of the shaft.

Article ID: 60099925

High performance V-belt XPA EPDM datum length 2057 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292057

Frequency:50 Hz
Speed:2960 1/min
Shaft Output:14487 W
Volume Flow:2985 m³/h
Pressure:Δp s9268 Pa
Pressure:Δp t10259 Pa
Density:43862 kg/m³
Sound Pressure:100 dB(A)

Length : 600 mm
BAR-ES-23-600-25-1M6-NW-B
SKU: SBAQA100010-600
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M6 (1x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Lifting eye bolt DIN 580 M6 x 13 steel C15E self coloured ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458006

Precision spur gear made of steel 16MnCr5 module 3 24 teeth bore 35mm hardened and ground outside diameter 78mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24382435

Neoprene timing belt HTD 8M width 50mm Lw 1760mm 220 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17554000

Service unit 3-part »FUTURA« with metal container, Viewing tube and pressure gauge, Size 1, G 1/4, Control range 0.2 - 4 bar, Semi
Three-piece service units with excellent flow rates in modern design.
Lockable diaphragm pressure regulator with secondary ventilation, oil can be filled without interrupting operation.

Sensor, »CS1« type, for round cylinder series »MI« and »MSI«, Piston Ø 32, REED sensor, 2-wire, M8 plug, 150 mm cable, NO
Sensors, »CS1« type

Short stroke cylinder, single-acting, Magnet, Piston Ø 32, Stroke 10, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 4x2, PN at 20 °C max. 44 bar, black, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Throttle check valve »Blue Series«, Discharge throttle, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-on hose connector, G 1/4 i., for hose I.D. 13 mm, AF 17, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Fitting 330, flat sealing, IT/IT, Rp/Rp 1 1/4, NBR seal, Operating temp. -20°C to 200°C, black malleable cast iron, Hot-dip galva.
Maximum temperature and maximum operating pressure should not occur at the same time!

Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Push-in T-fitting »Blue Series« mini, rotating, G 1/8, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

High performance V-belt XPA EPDM datum length 2060 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15292060

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:5434 W
Volume Flow:1153 m³/h
Pressure:Δp s7979 Pa
Pressure:Δp t8383 Pa
Density:43862 kg/m³
Sound Pressure:97 dB(A)

Length : 600 mm
BAR-ES-23-600-25-1M8-NW-B
SKU: SBAQA100030-600
Magnet quality: GSN-52
Interface/connection dim's: Threaded hole M8 (1x)
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Lifting eye bolt DIN 580 M8 x 13 steel C15E self coloured ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458008