Locking plug »value line«, Supports 4 mm, Operating pressure max. 16 bar, Operating temp. -20 °C to 70 °C, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Straight push-in fitting »Blue Series«, G 1/8 i., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pivoting angled fitting, G 1/8 o., Pipe exterior Ø 8 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Connection seal made of PA, Ø 18 x Ø 11.8 x 2 mm, for flange pressure controller 300 bar

Elbow 40, 45°, Rp 3/8 IT, R 3/8 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in bulkhead fitting »Blue Series«, M22x1, Rc 3/8 i., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

This micro-processed controller serves for temperature control at high measuring accuracy. Beside resistance sensors and semiconductor thermo element the multi-sensor sensor entrance can equally process 0... 10V and/or 4...20mA. The PID regulation and/or thermostat regulation can be activated via parameter setting. Outputs are two relay contacts and an analogue output. Red LED lamps indicate the status of the output relays. The desired values and parameters determining the process are adjusted with a 4-field plastic foil keyboard. 900305.025

Taper-bush 5050 bore 115mm
Material: GG25.

Bores ISO E8. Keyways in accordance with DIN 6885/1. Screws included in
delivery (spare screw product no. 622 516 99, order quantity as needed).
Screw size BSW 7/8" x 2 1/4". Spanner size 14 mm. Cone and front side
ground. Shaft tolerance +0,5mm / -0,125 mm. Can be used with or without
feather key, depending on the required torque. Other bush sizes and
bores are available on short notice (some in stock). Assembly
instructions
In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Fasting torque: 270 Nm. Slip torque without keyway: bore 75 mm: 3250 Nm;
bore 100 mm: 4800 Nm; bore 125 mm: 5900 Nm

Article ID: 62251694

Pressure Ranges -1 to 700 bar
Accuracy +/- 1%
50mm – 80mm Gauge Sizes

Frequency:50 Hz
Speed:2740 1/min
Shaft Output:127 W
Volume Flow:473 m³/h
Pressure:Δp s503 Pa
Pressure:Δp t632 Pa
Density:43862 kg/m³
Sound Pressure:70 dB(A)

DNG 7-60 UL 205573-1.030
277/480V, 5-60Hz
Emod-Motor 2,5kW
**replaces 77835-1.030
Three-Phase Low-Pressure Fan
Rotating direction: clockwise
Efficiency: IE3 on IEC 60034-30
Rated motor power: 2500 watts at 60Hz
Rated current: 7,3/4,2 amp.
Degree of protection: IP55
Insulation class: F
Number of poles: 2
Motor protection: PTC
Impeller material: Steel (galvanized)
Housing material: Steel sheet
Paint: RAL9005 deep black
Weight: 30 kg

Opening And Closing Contact İn One Housing Weight:0,08

1 kW

The performance of Airmar’s "1 kW, 260 family" of transducers is legendary. The combination of power and sensitivity has made this the high-performing transducer of choice with conventional fishfinders. Operating at 50 and 200 kHz, the narrow, 6° beam at 200 kHz provides excellent target resolution and crisp images of fish holding tight to wrecks and reefs. The 50 kHz is excellent at deep-water detection, and the wide 19° beam yields broad coverage under the boat.

The transducer is installed inside the hull in the included tank. The tank is cut to the boat’s deadrise angle to ensure that the transducer is properly oriented for optimal performance. The M260 is a popular choice for customers not wanting to drill holes in their hull and for trailered boats.

Diameter : 20 mm
HEPM-EP-D020-022-SW
SKU: GM17852
Stock: 11
Max. holding force: 40 N
Interface/connection dim's: Threaded hole M4
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 90 Dimension D x H (mm) 60 x 120

Flexible leads / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

IM General features
All coils are made of copper wires of class H (180°C).
30% glass fibre thermoplastic housing, insulation class F (155°C) suitable for continuous operation (100% ED).
Protection degree IP65.
Maximum ambient temperature 80°C.
Electric features
Quick connection connector DIN 43650,  suitable for all IM2 coils.
Cable gland Pg9 (cable diameter 6÷8 mm).
Pg11 cable gland thread;
Adjustable cable outlet in 4 positions every 90°.

BARREL NIPPLE LENGTH 300 MM - STAINLESS STEEL 316L

Information

Cylindrical nipple - Stainless steel 316L> DiamA " very available: from DN8 to DN50 - Gas thread> Characteristics of the cylindrical nipple - Stainless steel 316L: Tube RoulA (c) / SoudA (c) - Schedule 20S> Nominal pressure of the nipple cylindrical: PN50> ISO 7/1 standard

Washer DIN EN ISO 7089 (DIN 125 A) for M8 (8,4x16,0x1,6mm) material steel zinc plated
Material: Steel, zinc-plated.
Article ID: 65315800

Bevel gearbox KEK size 1 ratio 1:1 shaft diameter 6mm housing length 32mm
Angular drives with high torques at very low dimensions. Suitable in a wide variety of applications 7 Sizes. Ratio 1:1.Housing: Aluminium, silver anodized. Sealed against lubricant leaks, protected against dust. Can be mounted in any position.Gearing: Bevel gears from steel, surface hardened. Bearing: Ball bearings with rubber seal RS.Lubrication: Maintenance free grease lubrication. Angular backlash: 3°+/-1°.Operating time: 20% at 5 min. Life time: 1,000 hours at max. performance at speed 500 min-1and operating time 20%.Permiss. operating temperature: -20° to +60°C.
Article ID: 41000101

3-8 inch, 130 C

5/3-way valve, electropneum., Centre vented, Connection G 1/4, DN 7.5, 24 V DC, Operating temp. -10 °C to 60 °C, Aluminium

Throttle check valve »Blue Series«, Straight, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Compact cylinder »ACP«, double-acting, Piston Ø 32, Stroke 50, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

GEKA spray nozzle with coupling connector, bright brass, DN 19, Operating pressure max. 40 bar, Med./ambient temp. -10 °C to 90 °C
Claw couplings (claw distance: 40 mm) made of brass for water, industrial, mortar, suction and discharge hoses. Suitable for a wide range of applications, e.g. industrial plant engineering, civil and structural engineering, environmental engineering, manual trades, domestic water engineering, horticulture and landscaping, agriculture and forestry, etc.
Available in a rigid or 360° swivelling version. The two systems can also be easily coupled to one another!

Quick-connect coupling I.D. 5, bright brass, Sleeve I.D. 8, Operating pressure 0 - 35 bar, Medium / ambient temp. -20 °C to 100 °C
One-hand quick disconnect couplings, one side sealing, compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive, food technology.

Straight screw-in fitting »value line«, G 1/2 o., for hose exterior Ø 12 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Push-in T-connector »metallica«, for hose exterior Ø 12 mm, Working pressure max. 16 bar, Operating temperature -20 °C to 150 °C
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Weld-on coupler 16, Steel with a bare metal surface ST 37-2, Continuous thread, Rp 3/8, Length 26 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Straight push-in fitting »metallica«, G 1/8 i., for hose exterior Ø 6 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Angled screw-in fitting POM, G 1/4 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Elbow 1, 90°, long, Rp 1 1/4 IT, R 1 1/4 ET, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Pipe clamp, for »speedfit« series, Polypropylene, for pipe exterior Ø 12 mm, white, Temperature max. 90 °C
For fastening rigid PA or aluminium pipes to the wall.

Pressure gauge fitting, G 1/4 i., Pipe exterior Ø 10 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Straight hose connection supports, for hose I.D. 6 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Double threaded nipple 280, ET/ET, R 1 1/4, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in bulkhead fitting »Blue Series«, M22x1, Rc 1/4 i., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

This micro-processed controller serves for temperature control at high measuring accuracy. Beside resistance sensors and semiconductor thermo element the multi-sensor sensor entrance can equally process 0... 10V and/or 4...20mA. The PID regulation and/or thermostat regulation can be activated via parameter setting. Outputs are three relay contacts and an analogue output. Red LED lamps indicate the status of the output relays. The desired values and parameters determining the process are adjusted with a 4-field plastic foil keyboard.

Please note that the analogue output is not galvanically separated from the supply voltage. To avoid any problems operate the controller with a separate transformer. 900305.026

Taper-bush 4545 bore 75mm
Material: GG25.

Bores ISO E8. Keyways in accordance with DIN 6885/1. Screws included in
delivery (spare screw product no. 622 515 99, order quantity as needed).
Screw size BSW 3/4" x 2". Spanner size 14mm. Cone and front side ground.
Shaft tolerance +0,5 mm / -0,125 mm. Can be used with or without feather
key, depending on the required torque. Other bush sizes and bores are
available on short notice (some in stock). Assembly
instructions
In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Fasting torque: 190 Nm. Slip torque without keyway: bore 55 mm: 1840 Nm;
bore 75mm: 3000 Nm; bore 100mm: 4500 Nm

Article ID: 62251575

Pressure Ranges -1 to 700 bar
Accuracy +/-1%
72mm + 92mm Gauge Sizes (Square Face)

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

Frequency:50 Hz
Speed:2840 1/min
Shaft Output:120 W
Volume Flow:446 m³/h
Pressure:Δp s516 Pa
Pressure:Δp t630 Pa
Density:43862 kg/m³
Sound Pressure:70 dB(A

DNG 2-5D WS 205969-1.030
Wide-range voltage , 5-60Hz
Weight: 5kg

24V Dc, Changer, Breaking Capacity 16A Weight:0,08

1 kW

The TM260 comes with a rugged stainless-steel mounting bracket that is easy to install and has a streamlined shape. The performance of Airmar’s "1 kW, 260 family" of transducers is legendary. The combination of power and sensitivity has made this the high-performing transducer of choice with conventional fishfinders. Operating at 50 and 200 kHz, the narrow, 6° beam at 200 kHz provides excellent target resolution and crisp images of fish holding tight to wrecks and reefs. The 50 kHz is excellent at deep-water detection, and the wide, 19° beam yields broad coverage under the boat.

Ferrite 200 mm
HRA-F-052x17-AA-0200-B-B
SKU: TBAA020001
Stock: 16
Width: 52 mm
Height: 17 mm
Water-resistant: no
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 100 Dimension D x H (mm) 60 x 120

Flexible leads / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

Lockshield valve series 158 General features
Available with chrome frame finish
Micrometric regulation
Maximum pressure 10 bar
Auger retention with EPDM O Ring
Teng retention with O Ring
Thread according to UNI ISO 228
Body made of brass

WELDING NIPPLE LENGTH 300 MM - STAINLESS STEEL 316L

Informations

Embout mAC/le - Inox 316L > DiamA"tres disponibles : du DN15 au DN50- Filetage Gaz> CaractA(c)ristiques de l' embout mAC/le - Inox 316L :Tube RoulA(c) / SoudA(c) - Schedule 20S> Pression nominale de l' embout mAC/le : PN50> Norme ISO 7/1

Washer DIN EN ISO 7089 (DIN 125 A) for M10 (10,5x20,0x2,0mm) material steel zinc plated
Material: Steel, zinc-plated.
Article ID: 65316000

Precision spur gear made of steel 16MnCr5 module 1 30 teeth bore 12mm hardened and ground outside diameter 32mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 22483012

1-2 inch, 130 C

5/3-way valve, electropneum., Centre vented, Connection G 1/4, DN 7.5, 230 V, 50 Hz, Operating temp. -10 °C to 60 °C, Aluminium

Check valve, Straight-way variant, Brass, Medium/ambient temp. max. 180 °C, G 3/8 IT, PN max. 16 bar, Opening pressure 0.2-0.4 bar

Pushbutton safety coupling I.D. 8, ISO 6150 C, Stainless steel, Sleeve I.D.9, Operating pressure max. 16 bar, Temp. -20°C to 200°C
High quality, robust and long-lifetime quick connect coupling in a safety design that can be operated with one hand.
When pushed for the first time the coupling is vented, the plug remains securely in the coupling.
After a second push the plug is released.
This prevents a potential "whiplash effect" and the risk of operating personnel is practically excluded.

The safety version meets ISO standard DIN EN ISO 4414.

These safety couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, workshops, automotive, mining, offshore.

Straight push-in fitting, Exterior hexagonal, R 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 20 bar, Stainless steel
For use in more aggressive environments and corrosive media.

Double threaded nipple, M24x1.5 o., M24x1.5 o., AF 28, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Reducing nipple, Long type G 3/8 o., G 3/8 i., AF 19 Nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Screw-in hose connector, G 1 o., for hose I.D. 19, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.