Locking screw, Hexagonal socket 2.5 mm, M5, NBR O-ring, nickel-plated brass, Max. working pressure 25 bar, Max.operating temp.80°C
Suitable for air, water, oil, steam, etc.

Straight screw-in fitting, ET conical, R 1/2, for hose 8/6 mm, AF 22, Working pressure max. 18 bar, nickel-plated brass

Push-in L-fitting »Blue Series«, rotating, R 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Diaphragm

Amplification sleeve, Pipe exterior Ø 8/6 mm, Operating pressure max. 60 bar, Temperature max 150 °C, Bright brass

Worm thread - hose clamp »blow line«, Chrome steel (W2), Belt width 9.0 mm, Clamping range 25.0 - 40.0 mm

Hexagonal coupl. nut G 3/4, sleeve size I.D. 19, nickel-plated br., Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Straight reducer, Pipe exterior Ø Female connector 12/6 mm, PN max. 630 bar, a/f1 22, a/f2 24, a/f3 17, galvanised steel
Straight reducers, heavy type

Piston rod nut, for standard cylinder, Piston Ø 125, Piston rod thread M27x2
Rod nut

Reducing piece POM, Supports 10 mm, for hose exterior Ø 8 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

T-multi-distributor »Blue Series«, rotating, R 1/4 o., for hose exterior Ø 4x6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Ferrule, Pipe exterior Ø 6 mm, PN max. 630 bar, galvanised steel
Ferrule, heavy type

Nipple for coupl. I.D. 7.2 - 7.8, locking on both sides, Bright brass, G 3/8 IT, Operating pressure 0-35 bar, Temp. -20°C to 100°C

The controller ST710-JB1BV.10 was developed for simple thermostatic applications. Due to its complete equipment it can operate without any further components in many cases, e.g. cut-out relay or main switch.
The controller is supplied with 12-24V AC or 16-36V DC and has an output relay with an Ohm maximum electric load of 12A. The controller has 4 keys. Three of them are there to controller adjustments. The fourth key activates stand-by function. 900212.013

Pressure Ranges -1 to 700 bar
Accuracy +/-1%
60mm – 150mm Gauge Sizes
Safety Pattern Gauge

Rotating joint with aluminium-, stailnless steel or brassdesign for air, vacuum, hydraulic oil
Double flow with stationary syphon pipe with ISO 228-thread
internal term: RTO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

Frequency:50 Hz
Speed:2650 1/min
Shaft Output:75 W
Volume Flow:387 m³/h
Pressure:Δp s407 Pa
Pressure:Δp t506 Pa
Density:1.2 kg/m³
Sound Pressure:66 dB(A)

Frequency:50 Hz
Speed:2875 1/min
Shaft Output:642 W
Volume Flow:1127 m³/h
Pressure:1038 Pa
Pressure:1263 Pa
Density:43862 kg/m³
Sound Pressure:77 dB(A)
Weight: 26.5 kg

With Filter Mat P15/150S And Gasket Weight:0,06

Applications
Level measurement
Open channel flow
Proximity
Obstacle avoidance
Robotics
Specs English
Specs German
Specs Spanish

Diameter : 50 mm
HEPM-EM-D050-027-SW
SKU: GM17805
Stock: 26
Max. holding force: 700 N
Interface/connection dim's: Threaded hole M5
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 31,5 Homologation VDE | IMQ Dimension D x H (mm) 40 x 94

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

IM General features
All coils are made of copper wires of class H (180°C).
30% glass fibre thermoplastic housing, insulation class F (155°C) suitable for continuous operation (100% ED).
Protection degree IP65.
Maximum ambient temperature 80°C.
Electric features
Quick connection connector DIN 43650,  suitable for all IM2 coils.
Cable gland Pg9 (cable diameter 6÷8 mm).
Pg11 cable gland thread;
Adjustable cable outlet in 4 positions every 90°.

HEXAGONAL NIPPLE - STAINLESS STEEL 316

Information

Hexagonal nipple - Stainless steel 316> DiamA " very available: from DN6 to DN50- Gas thread> Nominal pressure of the hexagonal nipple: - 20 bar A 20AdegC- 16 bar A 100AdegC> Standard ISO 228-1

nut DIN 934 A2 M5 RH
Material: Stainless steel V2A (A2) or V4A (A4).Hexagon nuts according to the old standard DIN 934 with metric ISO thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65299005

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

1 1-2 inch, 130 C N-model: carbon graphite/silicon carbide seal (standard seal)
D-model: silicon carbide/silicon carbide seal (for applications with poor filtration water, or abrasive fluids)
Ballbearings (can be relubricated)
Robust and less influence of dirty media
Self supporting in innovative lightweightdesign – no additional support necessary
Rotor stainless steel

Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, eccentric, G 1/2, Meas. range 0-1.6 bar, Ø100
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Reducer, Pipe exterior Ø Female connector 14/6 mm, PN max. 630 bar, a/f1 17, a/f2 17, a/f3 27, galvanised steel
Reducer, heavy type

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 2, G 1/2, max. 25 bar, 0.5 - 16 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ16, Stroke50, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Strainer for check valves, G 2, Filter Stainless steel 1.4301, Plastic thread, Operating temperature -20 °C to 100 °C

Reducing nipple, Short design, G 3/4 ET, G 1/2 IT, AF 32, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Straight screw-on fitting G 3/8 i., for hose 9/12 mm, AF 22, Working pressure max. 10 bar (20 °C)/max. 1 bar (60 °C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Straight screw-in supports, R 1/8 o., for hose I.D. 8 mm, AF 10, Over-pressure max. 14 bar, Temperature range -40°C to 90°C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Reducing piece 241, R 1 1/2 ET, Rp 1/2 IT black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in L-fitting »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-in hose connector, G 3/4 o., for hose I.D. 13, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Replacement seal made of NBR, for Kamlok couplings made of aluminium, for coupling DN 25 (1")

Sintered bronze silencer, Brass thread / hexagonal, G 1/2, AF 23, Operating pressure 0 - 8 bar, Operating temp. -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Hexagonal coupl. nut G 1/4 sleeve size I.D. 4, I.D. 6, nickel-plated br., Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

Connection nipple for bellows suction cup, round, 1.5 and 2.5 folds »FGA« type, G 1/4 ET, for suction cup Ø 32 - 52 mm, I.D. 4,4
Connection nipples for bellows suction pads, round, 1.5 and 2.5 folds

Screw-in hose connector, R 3/8 o., for hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Double threaded nipple, Hexagonal, R 1/8, AF 12, Working pressure max. 20 bar, Stainless steel 1.4408

T-multi-distributor »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 4x8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Ferrule, Pipe exterior Ø 8 mm, PN max. 630 bar, galvanised steel
Ferrule, heavy type

Nipple for coupl. I.D. 7.2 - 7.8, locking on both sides, Bright brass, G 1/2 ET, Operating pressure 0-35 bar, Temp. -20°C to 100°C

The controller ST710-JBJV.10 was developed for simple thermostatic applications. Due to its complete equipment it can operate without any further components in many cases, e.g. cut-out relay or main switch. The controller can be supplied with 12-24V AC or 16-36V DC and has an output relay with an Ohm maximum electric load of 12A. The controller has 4 keys. Three of them are there to controller adjustments. The fourth key activates stand-by function. 900212.016

Timing belt pulley HTD 14M material steel 56 teeth for belt width 55mm for taper bush 3020
Material: Up to a Teeth Number of 56 phosphated steel, from a
Teeth Number of 64 phosphated grey cast iron GG25. Ready-to-install,
for use with taper-bushings. Taper-bushings are available for varios
shaft diameters and have to be ordered seperately.

In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Article ID: 17677228

Timing belt pulley HTD 8M material steel 72 teeth for belt width 50mm
Material: Up to a Teeth Number of 72 phosphated steel, from a
Teeth Number of 80 phosphated grey cast iron GG25.

The functionability of a belt drive is largely influenced by the quality
of the used pulley. HTD pulleys are precision components, manufactured
pitch-true with special cutters. This leads to a precise meshing of
teeth.

Article ID: 17443600

Pressure Ranges -1 to 700 bar
Accuracy +/-1%
100mm – 150mm Gauge Sizes

Rotating joint with aluminium-, stailnless steel or brassdesign for air, vacuum, hydraulic oil
Double flow with stationary syphon pipe with ISO 228-thread
internal term: RTO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

205573-1.030 replaces 77835-1.030 DNG 7-60 UL
277/480V, 5-60Hz Emod-Motor 2,5kW
Three-Phase Low-Pressure Fan
Rotating direction: clockwise
Efficiency: IE3 on IEC 60034-30
Rated motor power: 2500 watts at 60Hz
Rated current: 7,3/4,2 amp.
Degree of protection: IP55
Insulation class: F
Number of poles: 2
Motor protection: PTC
Impeller material: Steel (galvanized)
Housing material: Steel sheet
Paint: RAL9005 deep black
Weight: 30 kg

75484-1.030 DNG 4-14/WS; counter clockwisewide-range
Voltage: 5-60Hz Three-Phase Low-Pressure Fan
Rotating direction: counter clockwise
Rated power: 250/350 watts
Rated current: 2,8 amp.
Protection category: IP65
Insulation class: F
Number of poles: 2
Impeller material: sheet Steel (galvanized)
Housing material: sheet Steel
Varnishing: RAL9005 deep black
Terminal box position: L0
Weight: 10 Kg

For Lv 400-550 And Gv 400/500 Weight:0,06

Applications
Level measurement in chemically aggressive environments
Food and beverage processing
Flow monitoring
Specs English
Specs German
Specs Spanish

Description : Electronic polarity indicator
POLE INDICATOR ELECTRONIC
SKU: GM1841001
Stock: 22
With the polarity indicator, you can determine the orientation of a magnetic field by measuring whether a magnetic pole is a magnetic North (N) or South (S) pole. Suitable for detecting stray magnetic fields in packaging, performing magnet polarity checks, testing coils and use during the assembly of electric motors. There are types of pole indicators for 2D or 3D measurement, analogue or digital.

Indicates direction of magnetic field
Deliverable from stock
Analogue or digital
Two or three dimensional

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 35 Homologation VDE | IMQ Dimension D x H (mm) 45 x 94