Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, eccentric, G 1/2, Meas. range 0 - 10 bar, Ø100
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Captive seal ring made of PA6, Temperature max. 70 °C, for thread M5, PU 100 pcs.

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 25, Stroke 60, M5x0,8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Storz adapter, Aluminium, Storz size 65, Tappet distance 81 mm, G 3 ET, Operating pressure max. 16 bar, Temp. -40 °C to 110 °C
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Straight screw-in fitting, R 1/2 o., Pipe exterior Ø 15 mm, Operating pressure max. 60 bar, Temp. max 150 °C, nickel-plated brass

Push-in L-fitting »Blue Series«, Self-locking, G 3/8 o., for hose exterior Ø 10 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Bi-metallic thermometer for heating, Connection rear, G 1/2, Immersion shaft length 60 mm, Ø 80 mm, Display range 0 °C to 120 °C
Applications: Heating, plumbing, universal.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1/2, Length 40 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Angled connection »value line«, for hose 10/8 mm, AF 11, Operating pressure max. 18 bar, nickel-plated brass
Union elbows
Nickel-plated brass, »value line« Series

Screw-on connector, Brass 2.0401, M24x1.5 IT, Hose connection 19 mm, Operating pressure max. 15 bar, Temp. -20 °C to 160 °C

Sealing cone assembly, for pressure regulator for water, G 1/4

Push-in cartridge »Blue Series«, can only be pressed in plastic, for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Coupling nut, M10x1, for hose 6/4 mm, AF 12, Working pressure max. 18 bar, nickel-plated brass

Push-in L-fitting »metallica«, rotating, G 3/8 o., for hose exterior Ø 12 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Push-in T-fitting »Blue Series«, L-shape, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

T-fitting, Aluminium hollow screw rotating, G 1/4, for hose 6/4 mm, Operating pressure 0 - 10 bar, Temp. -10 °C to 60 °C, POM

Flat suction cup, round, Material NBR, »PFG«, ø:8, suitable connection nipple IT M5, suitable connection nipple ET M5
Robust and hard-wearing suction pad with a single sealing lip.
Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to handle smooth or slightly rough surfaces. Due to its flat shape, it can grip the workpiece in a very short time and withstand the forces that result from fast movement of the object during handling. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very short evacuation timesSuitable for high lateral forcesGood intrinsic stability when attached to the loadSupports on the bottomVery short cycle timesHigh suction forces with small dimensions

Applications:
Handling workpieces with smooth or slightly rough surfaces, e.g. metal sheets,
cardboard boxes, sheets of glass, plastic parts and sheets of wood.

Push-in L-fitting »Blue Series« long, rotating, G 3/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Safety ring, for »speedfit« series, for pipe exterior Ø 5 mm, red, POM

T-ring piece, for hollow screw G 3/8, for hose exterior Ø 12 mm, Working pressure max. 16 bar, Operating temp. -20°C to 70°C
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

The controller ST710-JBJA.10 was developed for simple thermostatic applications. Due to its complete equipment it can operate without any further components in many cases, e.g. cut-out relay or main switch. The controller is supplied with 230V AC and has an output relay with an Ohm maximum electric load of 12A. The controller has 4 keys. Three of them are there to controller adjustments. The fourth key activates stand-by function. 900212.005

Retaining ring DIN 472 13mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61761300

Timing belt pulley HTD 14M material steel 40 teeth for belt width 55mm for taper bush 2517
Material: Up to a Teeth Number of 56 phosphated steel, from a
Teeth Number of 64 phosphated grey cast iron GG25. Ready-to-install,
for use with taper-bushings. Taper-bushings are available for varios
shaft diameters and have to be ordered seperately.

In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Article ID: 17677220

Pressure Ranges -1 to 700 bar
Accuracy +/-1%
100mm + 160mm Gauge Sizes

Rotating joint with aluminium-, stailnless steel or brassdesign for air, vacuum, hydraulic oil
Double flow with stationary syphon pipe with ISO 228-thread
internal term: RTO One way: yes 2 way with a standing inner tube: No 2 way with rotating inner tube: No

Frequency:50 Hz
Speed:1320 1/min
Shaft Output:22 W
Volume Flow:215 m³/h
Pressure:Δp s77 Pa
Pressure:Δp t106 Pa
Density:1.2 kg/m³
Sound Pressure:51 dB(A)

75074-1.030 DNG 6-35/S;LINKS 230/400V,50HZ Three-Phase Low-Pressure Fan;
Rotating Direction: anticlockwise
Rated Power: 750 watts
Rated Current: 3,3/ 1,9 amp.
Protection Category: IP55
Insulation Class: F
Number of Poles: 2
Fan Wheel: Steel (galvanized)
Housing: sheet Steel
Varnishing: RAL9005 deep black
With hot bearing grease application;
Motor with aluminum electrode radiator;
With temperature lock;
housing open on both sides, without housing flange;
LK 175 with thread M5; cover plate
Weight: 14 Kg

M20 X 1,5 Weight:0,05

Applications
Level measurement
Open channel flow
Proximity
Obstacle avoidance
Robotics
Specs English
Specs German
Specs Spanish

Diameter : 25 mm
HEPM-EM-D025-020-SW
SKU: GM17802
Stock: 32
Max. holding force: 140 N
Interface/connection dim's: Threaded hole M4
Electro holding magnets are used for picking up, positioning and holding steel items. The round shape and a threaded hole at the bottom make them ideal for building into existing systems.These magnets are switched on and off with an electrical voltage.

For picking up, positioning or holding products
Switching: electric
Easy to install
Lifting power: up to 170 kg
Electropermanent or electromagnet

Application

Electro holding magnets can be used as:

Door magnets
Holding magnets are an essential component of a door magnet system. With the correct electromagnet, you build a secure system for automatically opening, closing or locking doors.
 
Pick & place magnet
Round electro holding magnets have a shallow magnetic field. This makes them particularly suitable for picking up, holding and unloading thin steel objects, up to 10 mm thick.
 
A known problem when picking up thin sheets with a powerful electro holding magnet is a too deep magnetic field radiation which causes the system to pick up several sheets at once. The use of many small electromagnets prevents this.
The maximum shear force is approximately 1/4 of the maximum holding force.
 
The central threaded hole on the back makes assembly very simple.

Working principle

Switchable with electric voltage

There are 2 types:
Electromagnet type attracts a steel object upon switching on the coil in the magnet. When the coil is switched off, the magnet immediately releases.
 
Electro-permanent magnet type possesses permanent magnet force. When the coil is turned off, the magnet pulls the workpiece. Switching on the coil neutralizes the permanent magnetic force. The magnet is now out of operation and immediately releases the workpiece.
 
These magnets are an ideal solution when you need to reliably hold the workpiece in the unpowered state.

Switching/power supply

Control of electro holding magnets

For the electrical switching and power supply of the magnets, a control cabinet is needed. These can be found in the accessories tab of the product variants.

Twin cableClimatic category -25 °C / +85 °C
Protection degree IP00
Loss Factor ≤ 5 x 10 ^-4 typical value
Test Voltage between terminals 1,75 Vn x 2 sec (min.)
Test Voltage between terminals and case 2 Vn x 2 sec (min.)
Rated Voltage 450 Vac
Rated Frequency 50 / 60 Hz
Capacitance Tolerance -/+ 5%
Operating class 400 V – B 10000 h (HPFNT)
450 V – C 3000 h (HPFPU)
Dielectric Self-healing MKP
Safety class S0
STANDARDS AND APPROVALS
Reference standards CEI EN 60252-1; VDE560-8
Homologation EN60252-1 (1.5 ÷ 45 µF)
EN60252-1 (1.5 ÷ 45 µF)
File E214047 (upon request) Cn
(µF) 22 Homologation VDE | IMQ Dimension D x H (mm) 40 x 94

Twin cable / Plane Base The MKA 450 capacitors are suitable for the heavy duty motor
applications.

G2 copper sheath General features
Copper sheath for C0 thermostats series
Electric features

BARREL NIPPLE LENGTH 80 MM - STAINLESS STEEL 316L

Information

Cylindrical nipple - 316L stainless steel> DiamA " very available: from DN10 to DN50 - Gas thread> Characteristics of the cylindrical nipple - 316L stainless steel: RoulA (c) / SoudA (c) tube - Schedule 20S> Nominal pressure of the nipple cylindrical: PN50> ISO 7/1 standard

internal term: P-ND One way : yes 2 way with a standing inner tube: no
190 C 17,0 bar water
Universal use – cooling, heating, clamping
With bellows sealing
Cartridge fast change CD-cartridge-design
Sealingmaterial ceramics/graphite
Ballbearings (can be relubricated)
No elastomers – therefore no temperature and chemical resistance problems
No loose parts, f.e. springs
Robust and less influence of dirty media
Self supporting – no additional support necessary
Available in stainless steel

Rotating joint type RL-ND – new design with bellows system cartridge, solid grease ballbearings, for universal use

Glycerine pressure gauge, bracket fastening, triangle front ring, Connection, rear, eccentric, G 1/2, Meas. range -1 / 0 bar, Ø100
Bourdon-tube pressure gauge in standard design, with clamp fixing.

For measurements in areas with high, dynamic pressure loads and vibration levels.
Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Captive seal ring made of PA6, Temperature max. 70 °C, for thread G 1/8, PU 100 pcs.

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 2, G 1/2, max. 25 bar, 0.1 - 3 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Storz coupling, Hose supports, for shell binding, rotating, Aluminium, Storz size 75-B, I.D. 75, Operating pressure max. 16 bar
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Reducing piece 241, ET/IT, R 4 o., Rp 3/2 i., Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Screw-in hose connector, R 3/8 o., for hose I.D. 10, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Straight screw-in fitting, G 3/8 o., for hose 9/12 mm, AF 22, Working pressure max. 10 bar (20°C)/max. 1 bar (60°C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1/2, Length 60 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Straight push-in fitting »Blue Series«, R 1/2 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight check valve »Blue Series«, Plug connector, for hose exterior Ø 12 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

Hose clamp, Malleable cast iron, 2-part, with loose tongues, Safety jaws, Clamping range 35 - 42 mm, for hose I.D. 25 (1")

Straight screw-in supports, R 1/8 o., for hose I.D. 6 mm, AF 10, Over-pressure max. 10 bar, Temperature range -40°C to 90°C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Replacement seal for standard jaw couplings according to DIN 3489, made of NBR, Oil resistant, -40 °C to 95 °C

Straight push-in bulkhead connector »metallica«, M20x1, for hose exterior Ø 12 mm, Working pressure max. 16 bar
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Push-in T-fitting »Blue Series«, L-shape, rotating, R 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight push-in fitting »click-clock«, G 1/4 i., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Plastic silencer, polyethylene, G 1/8, Pore width 40 - 50 µm, Operating pressure max. 6 bar, Operating temperature 5 °C to 80 °C
Important: The air flowing through the silencer is cooled down; at temperatures below zero, the moisture in the air can freeze, causing the pores of the silencer to close up.

Safety ring, for »speedfit« series, for pipe exterior Ø 6 mm, red, POM

T screw-in fitting, ET conical, R 3/8, for hose 12/10 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Nipple for coupl. I.D. 7.2 - 7.8, locking on both sides, Bright brass, G 3/8 ET, Operating pressure 0-35 bar, Temp. -20°C to 100°C

The controller ST710-JBBA.10 was developed for simple thermostatic applications. Due to its complete equipment it can operate without any further components in many cases, e.g. cut-out relay or main switch.
The controller is supplied with 230V AC and has an output relay with an Ohm maximum electric load of 12A. The controller has 4 keys. Three of them are there to controller adjustments. The fourth key activates stand-by function. 900212.008

Retaining ring DIN 472 16mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61761600

Timing belt pulley HTD 14M material steel 48 teeth for belt width 55mm for taper bush 3020
Material: Up to a Teeth Number of 56 phosphated steel, from a
Teeth Number of 64 phosphated grey cast iron GG25. Ready-to-install,
for use with taper-bushings. Taper-bushings are available for varios
shaft diameters and have to be ordered seperately.

In this youtube video we show the mounting and demounting of taper
bushes: Video clip (3.5
Minutes)
Article ID: 17677224

Timing belt pulley HTD 8M material steel 64 teeth for belt width 50mm
Material: Up to a Teeth Number of 72 phosphated steel, from a
Teeth Number of 80 phosphated grey cast iron GG25.

The functionability of a belt drive is largely influenced by the quality
of the used pulley. HTD pulleys are precision components, manufactured
pitch-true with special cutters. This leads to a precise meshing of
teeth.

Article ID: 17443200