5/2-way valve man. 90° lever bistable, G1/2, Operating pressure max. vacuum 10 bar, Operating temp. -10 °C to 60 °C
These pilot valves are also suitable for max. vacuum 10 bar.

Air gun with silencing nozzle, nickel-plated die-cast aluminium, Temperature range -10 °C to 50 °C, PN max. 10 bar, G 1/4 IT
Standard type.

For blowing out and cleaning machines, workpieces, bore holes, hollow parts, etc.

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ50, Stroke175, G1/8, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Hose with tyre valve connector, Length 50 cm, G 1/4, swiveling, for tyre gauges standard type

Push-in L-fitting »click-clock«, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Flat seal, (NBR with aramid fibres), for connection size (inch) 2 1/2, Operating temperature -20 °C to 200 °C
Maximum temperature and maximum operating pressure should not occur at the same time!

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 2.5 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in L-fitting »Blue Series«, Self-locking, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Spur gear made of polyacetal resin die-cast with hub module 0.5 45 teeth tooth width 3mm outside diameter 23.5mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28104500

Adjusting ring DIN 705 A set screw with slot bore 32mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62303200

Rod end GT-R DIN 12240-4 series K external thread M30x2 right maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299830

Product inlet/outlet size : Ø150 mm
SECF-B-D150-07E-N-F1E-W-B-B
SKU: SECF150638
Stock *: 0
Capacity: 3 to 7 m³/h
No of bars: 7 (3+4)
Build-in length: 250 mm
For magnetic filtering of small amounts, fine ferrous contaminants from granulates and dry, free-flowing powders in free-fall transport pipes.Industrial and hygienic versions available.

Manual quick cleaning
Types basic/food
2 magnetic grids, placed in cascade
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)
Capacity up to 45 m³/h

Application

Powders & granulates in free-fall pipes

Suitable for magnetic filtering of sporadically present, fine ferrous contaminants from granulates - such as plastics - and dry, free-flowing powders - like flour and sugar - in free-fall transport pipes.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids, placed staggered one above the other
Extractor bars Ø25/Ø23mm for 'quick cleaning'
Magnet quality neodymium N-42, 8,000 gauss on tube Ø25
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone EC1935 / FDA


Options

Available versions, options & accessories

Standard versions:

Basic type:

Industrial execution; grit blasted
Default with round or square in-/outlet
Food / pharma type:

Hygienic execution; polished
Default only with square inlet 
Options

High temperatures versions - to 140°C - not available in combination with ATEX
Steute door safety switch - for detecting if the separator is closed
White door seal instead of red
Inlet/outlet adapter pieces from square to round

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants always passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferrous particles. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.

Cleaning / iron discharging sequence

Stop the product flow
Loosen the fastener clamps
Shove the complete magnet unit out of the housing
Take the magnet unit out of the extractor unit and place it away from the extractor unit on a clean surface
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Shove the complete magnet unit assembly back into the housing
Tighten the fastener clamps
Restart the product flow

ZL31A General features
Controlled fluid: cold and hot water with max 50% glycol volume.
Controlled fluid temperature 5 ÷ 120 ° C.
High closing point (▲).
Stainless steel shutter.
Stem in stainless steel.
EPDM O-ring stem seal.
Flow rate characteristic: – regulation port A – AB: equal percentage (VDI / VDE 2173) n (gl) = 3, bypass B – AB: linear (VDI / VDE 2173);
Leakage rate: adjustment port A – AB: max 0.05% Kvs, bypass B – AB: max. 1% of the value of kvs.
PN 16 flanges (according to ISO 7005-2);
GG25 valve.
Nominal pressure 1600 kPa.
Differential pressure ∆pmax 400 kPa.
Electric features
Power supply: 230V 50/60Hz.
Power consumption:– from DN25 to DN50 – 6VA;– from DN65 to DN150 – 10VA.
Power supply cable 1m – 4×0,75 mm².
Tolerance range AC 198…264 V.

Clamp collar double-split stainless steel 1.4305 bore 80mm with bolts DIN 912 A2-70
Material: Stainless steel 1.4305. Screws stainless steel A2-70.Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores. The threads of the screws DIN 912 are covered with a layer of nylon. Tolerance b: +0.08mm -0.25mm . Temperature range: -40°C to +175°C.
Article ID: 62399480

Stainless steel container for stainless steel casting filter and stainless steel casting filter regulator, Size 4, G 1 and G 1 1/2

Reducer, cone seal, Pipe exterior Ø Female connector 14/8 mm, PN max. 630 bar, a/f1 19, a/f2 19, a/f3 27, galvanised steel
Reducer, with cone seal, heavy type

5/2-way valve, electropneumatic, »4V«, monostable, G 3/8, 24 V DC, Operating pressure 1.5 - 8 bar, Temp. -20 °C to 70 °C
5/2-way pilot valves
- Electro-pneumatic -

Low noise round nozzle, M12x1.25, Safety nozzle standard design, aluminium, Length 55 mm, Nozzles-exterior Ø 11 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Reducing nipple, R 1 o., G 1/2 i., AF 34, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Screw-on hose connector, G 3/8 i., for hose I.D. 9 mm, AF 19, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 16 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in L-fitting »Blue Series«, Self-locking, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Spur gear made of polyacetal resin die-cast with hub module 0.7 27 teeth tooth width 6mm outside diameter 20.3mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28202700

Rod end GT-R DIN 12240-4 series K external thread M30x2 left maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299930

Product inlet/outlet size : Ø250 mm
SECF-B-D250-11E-N-F1E-W-B-B
SKU: SECF250638
Stock *: 0
Capacity: 12 to 30 m³/h
No of bars: 11 (5+6)
Build-in length: 250 mm
For magnetic filtering of small amounts, fine ferrous contaminants from granulates and dry, free-flowing powders in free-fall transport pipes.Industrial and hygienic versions available.

Manual quick cleaning
Types basic/food
2 magnetic grids, placed in cascade
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)
Capacity up to 45 m³/h

Application

Powders & granulates in free-fall pipes

Suitable for magnetic filtering of sporadically present, fine ferrous contaminants from granulates - such as plastics - and dry, free-flowing powders - like flour and sugar - in free-fall transport pipes.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids, placed staggered one above the other
Extractor bars Ø25/Ø23mm for 'quick cleaning'
Magnet quality neodymium N-42, 8,000 gauss on tube Ø25
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone EC1935 / FDA


Options

Available versions, options & accessories

Standard versions:

Basic type:

Industrial execution; grit blasted
Default with round or square in-/outlet
Food / pharma type:

Hygienic execution; polished
Default only with square inlet 
Options

High temperatures versions - to 140°C - not available in combination with ATEX
Steute door safety switch - for detecting if the separator is closed
White door seal instead of red
Inlet/outlet adapter pieces from square to round

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants always passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferrous particles. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.

Cleaning / iron discharging sequence

Stop the product flow
Loosen the fastener clamps
Shove the complete magnet unit out of the housing
Take the magnet unit out of the extractor unit and place it away from the extractor unit on a clean surface
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Shove the complete magnet unit assembly back into the housing
Tighten the fastener clamps
Restart the product flow

EV70A Telecontrol General features
Instrument customisable via PC for all parameters.
Extractable terminal block for fast replacement of the instrument.
Lateral serial port for connection to the modem, separate from the front port to allow easy connection to the programming PC.

Flanged bush BBP bore 20mm polyamide 6.6 outer diameter 24mm length 15mm flange diameter 30mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62383200

Worm gear unit G/II version A centre distance 31mm i=30:1 (For operating instructions please visit the download area of our website www.maedler.de)
Housing: Aluminium permanent-mould casting, fully sealed against oil leaks and protected against dust, can be mounted in any position. Gear set: Worms hardened and ground, worm gears made from special bronze. Bearing System: Input and output shaft with roller bearing. Lubrication: As a special gearbox oil has been used, in most applications no relubrication or change is required. Input shaft is the smaller shaft d1. The permiss. output torque refers to shaft d2. Load Bearing Capacity of the Output Shaft Radial = 100 N, Axial = 60 N.

Article ID: 42003000

Pillow block bearing unit EK 15 bore 15mm material steel nickel plated
Material: Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearings from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the fixed side. With two angular contact ball bearings, lightly preloaded, with seals. Types EK06 and EK08 sealed only on the side without the nut. With 2 mounting holes. Locknut and distance bushes are included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for support side: Pillow Block Bearing EF. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201315

Multi-base plate for the way valves, Base plate for 10 valve positions, for valves connection G 1/8
Light alloy manifold bases for 2 to 10 valve positions.

Nipple for couplings I.D. 7.2 - 7.8, »stream line«, hardened / galvanised steel, for hose 13.5x9.5, Operating pressure max. 16 bar

5/2-way valve, electropneumatic, »4V«, monostable, G 3/8, 230 V, 50 Hz, Operating pressure 1.5 - 8 bar, Temp. -20 °C to 70 °C
5/2-way pilot valves
- Electro-pneumatic -

Low noise round nozzle, 1/2 - 27 UNS, Safety nozzle for high performance air gun, aluminium, Nozzles-exterior Ø 11 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Fitting 330, flat sealing, IT/IT, Rp/Rp 1, black malleable iron fitting, Operating temp. -20 °C to 200 °C, ISO 7-1
Maximum temperature and maximum operating pressure should not occur at the same time!

According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/4, Goods class 1.6, Measurement range 0 - 25 bar, Ø 50
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Replacement sieve for dirt strainers made of brass, for connection size G 3/4, mesh width 0.2 mm, DN 20

Reducing nipple, R 3/4 o., G 1/8 i., AF 17, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Adjusting ring DIN 705 A set screw with slot bore 36mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62303600

Product inlet/outlet size : Ø300 mm
SECF-B-D300-13E-N-F1E-W-B-B
SKU: SECF300638
Stock *: 0
Capacity: 18 to 45 m³/h
No of bars: 13 (6+7)
Build-in length: 250 mm
For magnetic filtering of small amounts, fine ferrous contaminants from granulates and dry, free-flowing powders in free-fall transport pipes.Industrial and hygienic versions available.

Manual quick cleaning
Types basic/food
2 magnetic grids, placed in cascade
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)
Capacity up to 45 m³/h

Application

Powders & granulates in free-fall pipes

Suitable for magnetic filtering of sporadically present, fine ferrous contaminants from granulates - such as plastics - and dry, free-flowing powders - like flour and sugar - in free-fall transport pipes.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids, placed staggered one above the other
Extractor bars Ø25/Ø23mm for 'quick cleaning'
Magnet quality neodymium N-42, 8,000 gauss on tube Ø25
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone EC1935 / FDA


Options

Available versions, options & accessories

Standard versions:

Basic type:

Industrial execution; grit blasted
Default with round or square in-/outlet
Food / pharma type:

Hygienic execution; polished
Default only with square inlet 
Options

High temperatures versions - to 140°C - not available in combination with ATEX
Steute door safety switch - for detecting if the separator is closed
White door seal instead of red
Inlet/outlet adapter pieces from square to round

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants always passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferrous particles. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.

Cleaning / iron discharging sequence

Stop the product flow
Loosen the fastener clamps
Shove the complete magnet unit out of the housing
Take the magnet unit out of the extractor unit and place it away from the extractor unit on a clean surface
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Shove the complete magnet unit assembly back into the housing
Tighten the fastener clamps
Restart the product flow

ECCS..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for hot water up to 90°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

Shaft collar DIN 705 A set screw with slot bore 9mm black finishing
Light-duty series. With set screw DIN EN 27 434 made from steel with black oxide finish. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62389009

Worm gear unit G/II version A centre distance 31mm i=5:1 (For operating instructions please visit the download area of our website www.maedler.de)
Housing: Aluminium permanent-mould casting, fully sealed against oil leaks and protected against dust, can be mounted in any position. Gear set: Worms hardened and ground, worm gears made from special bronze. Bearing System: Input and output shaft with roller bearing. Lubrication: As a special gearbox oil has been used, in most applications no relubrication or change is required. Input shaft is the smaller shaft d1. The permiss. output torque refers to shaft d2. Load Bearing Capacity of the Output Shaft Radial = 100 N, Axial = 60 N.

Article ID: 42000500

Safety handwheel SHR material aluminium diameter 125mm
Material: Aluminium, polished. Coupling attachment assembled. Can only be supplied with revolving, cylindrical handle made from plastic with threaded steel bolt and with hub keyway. According to safety regulations, handwheels must be mounted on the shaft in such a way that they do not rotate along with the machine drive. Safety handwheels comply with this regulation. Procedure: Wheel disengaged if not used. By axial displacement of the wheel (pulling) the two serrated wheel rims are engaged. The wheel is now positively keyed to the shaft. When the wheel is released, it automatically disengages. The coupling elements are assembled together in an enclosed unit. Coupling attachment made from steel, nitrided, bearing surface ground and PTFE coated, for minimal friction between bearing surfaces and high wear resistance. An oil hole is provided, which serves to connected to a pressure oiler in the wheel hub. Frequent lubrication is an important precondition in guaranteeing the correct functioning of the plain-bearing coupling attachment. The range of application of these handwheels is limited to low shaft speeds, or to higher speeds of only short duration (e.g. feed screws for milling machine table with rapid feed). The coupling attachments can also be supplied separately, to be mounted with existing handwheels. Prices on request. We assume no liability for any consequential damage.

Article ID: 67061200

Pressure switch for compressors, Three-phase current design, Flange F4 1/2, Medium temperature-5 °C to 80 °C, G 1/2, 6 - 16 bar

Blow gun, Plastic, extension tube 105 mm, noise-reducing nozzle, Nipple ID 7.2, Operating temp. -20 °C to 45 °C, PN max. 10 bar
For blowing out and cleaning machines, engines, bearings, sliding surfaces, bores of all kinds, hollow parts, moulds, etc.
The compressed air guns are supplied in a blister package with Euro holes.

5/2-way valve, electropneumatic, »4V«, monostable, G 1/4, 24 V DC, Operating pressure 1.5 - 8 bar, Temp. -20 °C to 70 °C
5/2-way pilot valves
- Electro-pneumatic -

Low noise round nozzle, G 3/8 ET, Safety nozzle general applications, nickel-plated brass, Length 55 mm, Nozzles-exterior Ø 11 mm
If correctly designed, these noise-reducing nozzles guarantee a lower noise level than conventional one-hole types with an identical blowing force.

They are usually fitted with a noise-reducing plastic insert and they are recommended by the German BGIA (Institute for Occupational Safety and Health).

Angled bulkhead connector, M10x1, for hose 4/6 mm, AF 14, Working pressure max. 10 bar (20 °C)/max. 2.5 bar (90 °C), PP
Chemically resistant to almost all inorganic acids and bases, even in high concentrations and at temperatures greater than 90 °C.

Replacement sieve for dirt strainers made of brass, for connection size G 1, mesh width 0.3 mm, DN 25

Worm thread hose clamp, Chrome steel 1.4016 (W2), according to DIN 3017, Clamping range 90.0 - 110.0 mm, Belt width 12.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, bright galvanised steel, passivated blue.

Adjusting ring DIN 705 A set screw with slot bore 38mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62303800

Product inlet/outlet size : #146 mm
SECF-B-1515-05E-N-F5m-W-B-B
SKU: SECF150538
Stock *: 0
Capacity: 1 to 3 m³/h
No of bars: 5 (2+3)
Build-in length: 160 mm
For magnetic filtering of small amounts, fine ferrous contaminants from granulates and dry, free-flowing powders in free-fall transport pipes.Industrial and hygienic versions available.

Manual quick cleaning
Types basic/food
2 magnetic grids, placed in cascade
Magnetic bars in extractor tube (Ø23|Ø25 mm, 10.700 | 8000 gauss)
Capacity up to 45 m³/h

Application

Powders & granulates in free-fall pipes

Suitable for magnetic filtering of sporadically present, fine ferrous contaminants from granulates - such as plastics - and dry, free-flowing powders - like flour and sugar - in free-fall transport pipes.
 
NOT suitable for poorly flowing sticky / fatty powders that cause blockages. Rotating Cleanflows are a better solution for those applications.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

2 Magnetic grids, placed staggered one above the other
Extractor bars Ø25/Ø23mm for 'quick cleaning'
Magnet quality neodymium N-42, 8,000 gauss on tube Ø25
Materials - in contact with product: AISI316(L)
Material gaskets: Silicone EC1935 / FDA


Options

Available versions, options & accessories

Standard versions:

Basic type:

Industrial execution; grit blasted
Default with round or square in-/outlet
Food / pharma type:

Hygienic execution; polished
Default only with square inlet 
Options

High temperatures versions - to 140°C - not available in combination with ATEX
Steute door safety switch - for detecting if the separator is closed
White door seal instead of red
Inlet/outlet adapter pieces from square to round

 
Online accessories & spare parts
Click on a product variant to find the online available accessories & spare parts.

Working principle / video

Filtering & discharging of ferrous contaminants

How does the magnetic filtering work?
The magnetic grids with very strong neodymium magnetic bars are positioned in the middle of the product flow. The product with ferrous contaminants always passes 2 magnetic bars while flowing through the separator.
 
The magnets attract passing ferrous particles. The captured particles stick to the magnets, while the purified product flows further.
 
How does the cleaning / iron discharging work?
Once the product flow is stopped, you take the entire magnetic grid unit out of the product channel.
 
Then pull the magnetic bars out of the extractor tubes, causing the ferrous particles to fall off the extractor tubes.

Cleaning / iron discharging sequence

Stop the product flow
Loosen the fastener clamps
Shove the complete magnet unit out of the housing
Take the magnet unit out of the extractor unit and place it away from the extractor unit on a clean surface
Catch the ferrous particles that now will fall off the tubes and dispose them
Wipe clean all parts with a soft cloth and - if necessary - a suitable cleaning fluid
Shove the magnet unit back into the extractor unit
Shove the complete magnet unit assembly back into the housing
Tighten the fastener clamps
Restart the product flow

ECC60MBUS General features
M-Bus interface for datalogger ECC250LOG.
Manages up to 60 M-Bus devices.
It can operate as a signal booster / repeater.
Communication speed from 300bps to 9600bps.
Power supply 24Vdc.
Maximum power consumption 12W.
Short-circuit protection and surge protection.
USB connection for meter reading through ECC60MBUS TOOLKIT.

ES-bolt for Clevis DIN 71752 size 6 x 24 steel zinc-plated
Material: Steel zinc-plated. ES-Standard 01.* Size 20 is not part of the DIN.
Article ID: 63740600

Worm gear unit G/II version A centre distance 31mm i=7:1 (For operating instructions please visit the download area of our website www.maedler.de)
Housing: Aluminium permanent-mould casting, fully sealed against oil leaks and protected against dust, can be mounted in any position. Gear set: Worms hardened and ground, worm gears made from special bronze. Bearing System: Input and output shaft with roller bearing. Lubrication: As a special gearbox oil has been used, in most applications no relubrication or change is required. Input shaft is the smaller shaft d1. The permiss. output torque refers to shaft d2. Load Bearing Capacity of the Output Shaft Radial = 100 N, Axial = 60 N.

Article ID: 42000700

Pressure switch for compressors, Three-phase current design, Flange F4 1/2, Medium temperature -5 °C to 80 °C, G 1/2, 6 - 16 bar

Check valve, Inclined seat design, Brass, Medium / ambient temp. max. 80 °C, Rp 1/2, PN max. 10 bar, Opening pressure 0.5 bar

5/2-way valve, electropneumatic, »4V«, monostable, G 1/2, 230 V, 50 Hz, Operating pressure 1.5 - 8 bar, Temp. -20 °C to 70 °C
5/2-way pilot valves
- Electro-pneumatic -

Round cylinder TP (ISO 6432) double-acting, Piston Ø 20, Stroke 25, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 60 °C
Inexpensive standard version with aluminum pipe and magnet piston.
Suitable for filtered (50 µm), unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjustable male connector, with cone seal, M12x1.5 o., Pipe exterior Ø 8, PN 315, a/f1 17, a/f2 17, galvanised steel