Bushing 270, IT/IT, Rp 3/4, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Suitable for belt width : 1200 mm
ROP-F1-C-120-M-D-L-B-B-B-NA
SKU: SAPB120520
Stock *: 0
Advised max. installation height: 230 mm
Suitable for: Cross mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

ECMCA General features
With filter and balancing valve

Elastic coupling RNH with half shell clamps backlash-free size 38 boreholes 44mm outer diameter 80mm overall length 114mm insert 98° shore red
Material: Hubs made from Aluminium. Spider made from Polyurethane. Shore hardness 98°A (red). - Zero backlash, insertable elastic coupling. - With removable half shell clamps, ready-to-install for rapid mounting with the possibility of demounting without removal of the other units. - Many different sizes and diameters available. - Size exchangeable with couplings RN, RNK and couplings from many other suppliers. On request with soft spiders 92°A. Temperature range: -30°C to +90°C. Note: Bores with * are pilot bores (not H7). The torque depends on the size of the finished bore.
Article ID: 60553844

Precision double universal joint WDN with needle bearing DIN808 bore 16H7 with keyway DIN 6885-1 tolerance JS9 on both sides
Material: Steel 35SMnPb10. Bearing parts 18NiCrMo5Pb. Max. Operating Angle 90°. The needle-bearing universal joints have almost zero backlash, high accuracy and good turning properties. These special needle-rollers without cage can take high loads even at large operating angles. A special grinding process realizes a perfect parallelism of the axes and the single parts of the joints - which guarantees an extremely long service life. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63163200N

Diaphragm pressure gauge, Robust design, Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0 - 16 bar, Ø 100
Diaphragm pressure gauge in robust design or for chemical applications.

Suitable for gaseous or liquid media, chemical applications type also suitable for use in corrosive atmosphere.

3/2-way valve »Blue Series«, Plug connector, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Compact cylinder »ACP«, double-acting, Piston Ø 50, Stroke 25, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 3x1.5, PN at 20 °C max. 44 bar, blue, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Hexagonal coupl. nut G 1, sleeve size I.D. 25, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Straight push-in fitting »Blue Series«, round, R 1/2 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

T-multi-distributor »Blue Series«, rotating, G 1/8 o., for hose exterior Ø 4x8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-in hose connector, G 1/8 o., for hose I.D. 6 mm, AF 14, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Suitable for belt width : 1400 mm
ROP-F1-C-140-M-D-L-B-B-B-NA
SKU: SAPB140520
Stock *: 0
Advised max. installation height: 230 mm
Suitable for: Cross mounting
Cost effective solution. Suitable for thin to thick layers and do not require a control box. Very reliable and available in many belt widths. Available in transverse or in-line versions for installation above your conveyor belt or end pulley.

Cross or inline version
For belt width 400-1600 mm
Easy to install
Permanent magnet
Max. installation height 450 mm

Application

Application

An overbelt magnet is suitable for removal or separation of high volumes of iron or steel and hangs above a flat- or trough-shaped conveyor. This type of magnet is self-cleaning and continuously separates (ferromagnetic) Fe parts from material streams. The iron removal efficiency of overband magnets ranges from 70 to 90%. This depends on magnet design, product flow and placement. Automatic self-cleaning overband magnetic separators are suitable for both the recovery (recycling) of ferrous parts and the removal/elimination of impurities (iron contaminants).
These magnets are mainly suitable for coarser fractions with pieces larger than 10 mm. Thanks to the robust, reliable technology, these magnets have applications in many industries. Putting a permanent overbelt magnet in service requires nothing more than four suspension points, sufficient space and power to drive the conveyor belt.

Operation

Operation

Conveyor belt speed:
to remove ferrous or iron parts from a material flow, they must remain in a magnetic field for between approximately 0.3 and 0.5 seconds, where they are magnetized. To achieve maximum separation, it is important to optimally match the size of the magnet block (main pole) and the belt speed. This means that with a narrow overband magnet the conveyor belt beneath it must run at lower capacity (m/s) than with a wider magnet at the same suspension height. The following formula provides an indication of the maximum conveyor belt speed:
 
Maximum conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)
 
Recommended conveyor belt speed (b) = block magnet width (a) / 0.3 (sec.)

Placement

Placement

The distance between a magnet and the conveyor belt must be as small as possible. The magnetic force decreases exponentially with increasing distance. There is, however, a minimum distance required so the rubber cleats safely remove all the ferrous parts from the material flow. There are two methods for use/placement of overband magnets: transverse and in-line. Goudsmit has a specific, optimum magnet configuration for both mounting options.
 
Transverse ('Cross')
In practice, transverse placement is most common, because it is easier to install in an existing line. An additional advantage is a ferrous discharge to the side, which from the logistical perspective is easier to process.
 
'In-line'
If you have the option to place your overband magnet in line with the conveyor belt, this is always preferred. The advantage of this is that the transported material ‘breaks open’ at the end of the belt (head roller) and is therefore suspended in mid-air for several milliseconds. As a result, the magnet can easily pull the ferrous metal out of the product flow.

Non magnetic zone

Non magnetic zone

When positioning the magnet, the construction below the magnet such as the frame, bearing rollers and end rollers must be made of non-magnetic material. This is because steel parts will become magnetized, which will adversely affect the separation performance of the overband magnet.
 
For more information and the rule of thumb, see: Non-magnetic-zone

EV70D Telecontrol General features
Instrument customisable via PC for all parameters.
Extractable terminal block for fast replacement of the instrument.
2-line display for setting parameters, remote monitoring and management for both GSM modem ( mobile telephony) and PSTN modem ( fixed telephony)
Mounted on DIN rail ( 9 modules)
Electric features
Absorption 10VA
8 digital inputs ON- OFF
4 analog inputs, via detection probes
4 output relays
Contact rating 5A- 230Vac ( ohmic charge).

Electric drip-feed oiler ELO 230V 50Hz capacity 1000ml
Material: Brass nickel-plated. Glass cylinder made from acrylic glass. Voltage: On choice: 230V AC, 50Hz, or 24V DC. Drip rate normal: about 45 drops per 1 ml. Other than the manual drip-feed oiler, which also drips when the machine has stopped, the electric drip-feed oiler only drips as long as the machine is running. When the machine stops, the electric drip-feed oiler is also automatically shut off, as the oiler is controlled via the machine programme. Finest dosing of drops is possible - by turning a knurled nut at the top part of the oiler. Almost all liquids can be dosed drop by drop, provided they are not mixed with solid matters. It is also suited for other media, provided they do not thicken with heat. Attention must be paid to the compatibility with acrylic glass and buna N used as sealing material. (possibly natural glass and vitone sealings on request). Duty cycle: intermittent 20%. Protection class acc. to EN 60529: IP20. Power consumption: 12VA (12W).
Article ID: 68030500

Spur gear made of POM with hub module 3 45 teeth tooth width 25mm outside diameter 141mm
Material: POM, white / nature, milled teeth. Tooth quality 10d25 DIN 3967. Pressure angle 20°. Untoleranced dimensions in accordance with DIN ISO 2768 middle. Temperature limit: continuous 100°C, only short time 160°C. Water absorption (satiable) 0,5% Cws.
Article ID: 29804500

Stainless steel ball valve, 2-piece, IT/IT thread, G 2, DN 50, Operating temperature -20 °C to 180 °C, PN max. 63 bar

Safety ball valve, lockable, Venting hole M5, nickel-plated brass, Operating temp. -10 °C to 100 °C, Rp 1/2, DN 15, PN max. 14 bar
Safety ball valves, two parts, made of nickel-plated brass.
Specially designed for pneumatic applications.
The valve shuts off the supply line and bleds the application area.
Lockable hand lever in closed position ensures a high protection against manipulation.

Straight push-in fitting, Exterior hexagonal, R 3/8 i., for hose exterior Ø 14 mm, Working pressure max. 20 bar, Stainless steel
For use in more aggressive environments and corrosive media.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 3x1.5, PN at 20 °C max. 44 bar, black, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Short reducer, Soft sealing, G 1 o., G 1/2 i., PN max. 400 bar, AF1 41, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Straight push-in fitting »Blue Series«, round, G 1/2 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series« long, rotating, G 1/2 o., for hose exterior Ø 12 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Y hose connection supports, for hose I.D. 13 mm, Bracket 90°, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Chain connecting link type 11 / E for roller chain 12 B-1 pitch 3/4x7/16" packing unit 5 pieces
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.* Company standard.** Packing units of 5 pieces.
Article ID: 10700300

ZD..NA General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Electric drip-feed oiler ELO 24V DC capacity 1000ml
Material: Brass nickel-plated. Glass cylinder made from acrylic glass. Voltage: On choice: 230V AC, 50Hz, or 24V DC. Drip rate normal: about 45 drops per 1 ml. Other than the manual drip-feed oiler, which also drips when the machine has stopped, the electric drip-feed oiler only drips as long as the machine is running. When the machine stops, the electric drip-feed oiler is also automatically shut off, as the oiler is controlled via the machine programme. Finest dosing of drops is possible - by turning a knurled nut at the top part of the oiler. Almost all liquids can be dosed drop by drop, provided they are not mixed with solid matters. It is also suited for other media, provided they do not thicken with heat. Attention must be paid to the compatibility with acrylic glass and buna N used as sealing material. (possibly natural glass and vitone sealings on request). Duty cycle: intermittent 20%. Protection class acc. to EN 60529: IP20. Power consumption: 12VA (12W).
Article ID: 68033500

Ball head precision levelling adjuster with locknut MN 686.9 30-11.0
Material: 42CrMo4V, Nr. 1.7225, zinc plated and blue passivated. For non-parall surfaces up to 4° slope. Larger overall height with more adjustment travel. With lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (steel bolt strength class 8.8, stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68692500

Compact cyl.ISO 21287, double-acting, female piston rod,magnet,PistonØ125, Stroke30,G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Straight push-in bulkhead connector reducing »click-clock«, M20x1, for hose exterior Ø 10/12 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Push-in T-fitting, L-shape, rotating, G 1/4 o., for hose exterior Ø 4 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 4x2, PN at 20 °C max. 44 bar, green, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Bellows suction cup, Round 2.5 folds, Silicone material, »FG«, suitable connection nipple IT G 1/8, ET M5 / G 1/8 Ø9mm
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Soft, flexible foldsSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Push-in fitting 45° »Blue Series«, rotating, R 1/8 o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 3, Length 100 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Straight screw-on fitting, »value line«, G 1/8 i., for hose 6/4 mm, AF 14, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

Feather key DIN 6885 version A 8 x 7 x 55 mm material C45
Material: C45K.Version A.
Article ID: 61815500

Length : 1600 mm
SVM-F-780x313-1600-B-F0E
SKU: SVMF071600
Stock *: 0
Advised max. installation height: 165-320 mm
Height: 385 mm
Removal of pieces of steel in the recycling industry or for protection of grinding mills. For installation up to 400 mm above conveyor belt.

Max. installation height 400 mm
Capture Fe particles from 1 mm
Various dimensions and flange types
For belt width 400-1600 mm
Easy to install

Application

Application

Permanent ferrite suspended magnets (block magnets) consume no energy, which is one of the factors that makes them so price effective. These magnets remove ferromagnetic (Fe) particles as small as 0.5 mm (depending on the layer thickness on the belt).

Cleaning

Cleaning

Cleaning of the block magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning), by swinging the extractor plate away from the magnet; the Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field.

Placement

Placement

A block magnet is hung above a conveyor belt, by means of chains or cables. The addition of these magnets can considerably boost separation yield:
 
Placement over pulley: In this configuration the magnet hangs at an angle over the end of the conveyor belt, where discharge of the material occurs. This is the ideal situation, because the bulk flow is ‘broken open’ at this point. When this happens, the iron particles are exposed within the surrounding material. This allows them to be more easily drawn to the magnet. Keep in mind, however, that it is important for the construction directly beneath the magnet to be made of non-magnetic material; otherwise it, too, will become magnetized.
 
Placement over band: This position is used for small layer thickness (or mono-layers). Or when there is no other option due to the potential for magnetization of underlying steel components (such as motors or guide rollers).

Working principle

Working principle

Suspended magnets (block magnets) remove undesirable ferromagnetic (Fe) particles such as iron and steel from material flows containing relatively little Fe contamination. They are placed above flat or trough-shaped conveyor belts. The metal particles are drawn out of the raw material flow and held by the magnet. This results in a pure iron fraction suitable for immediate reuse (recycling).
 
They are used to check incoming product flows and for the protection of machines, such as shredders and sieves. When heavy metal contamination is present, it is better to use an overbelt magnet; this type continuously carries away the iron particles.

K12C General features
Cable composition:– 2 conductors x 1.5 mm²– PVC sheath– Nickel-chromium heating element– Internal splicing point– Silicone insulation
Maximum room temperature powered 40 °C
Minimum installation room temperature -20 °C
Minimum storage room temperature -20 ÷ -25°C
Maximum length of the heating circuit  from the supply point 160 m
Electric features
Power supply 230V-50Hz
Constant power delivered ~10W/m

Polyurethane timing belt HTD 14M width 85mm 14M-85 open length
Material: Thermoplastic polyurethane (TPU), white, with steel tensile member. Good resistance against oil, fats and many chemicals. Temperature range -30º to +80ºC. Belts made of TPU can be welded to endless belts. When welded, the perm. tensile force is reduced to 50%.
Article ID: 17766500

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ125, Stroke30, G1/4, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Bushing, round, G 1 1/2, Working pressure max. 20 bar, Stainless steel 1.4408

Cross fitting, Pipe exterior Ø 22 mm, PN 160, A/F1 36, A/F2 27, galvanised steel
Cross-fitting, light type

Polyamide hose (PA 12 PHL), Temperature -40 °C to 80 °C, Hose Ø 4x2, PN at 20 °C max. 44 bar, silver, Roll of 25 m
PA 12 is resistant to corrosion even at temperatures as low as -40 °C.
It has a low water absorptive capacity and is therefore dimensionally stable if the ambient humidity varies.
PA 12 resists greases, oil, fuels, hydraulic fluids, alkalis and salt solutions.
Sufficient UV resistance can only be guaranteed if the material is pigmented black!
Suitable for use with push-in fittings. Suitable for vacuum up to 12x9 mm.

Main applications:
- Compressed air lines (low-pressure range) in industry and manual trades.
- Hydraulic lines (miniature hydraulics) in instrumentation and control.
- Lines for liquid and free-flowing substances.
- Pneumatic braking systems in motor vehicles and trailers (DIN 73378:1996-02 and DIN 74324-1:1996-02).
- Fuel and lubricant supply systems.
- Vacuum lines

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, G 1/8 IT, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Bulkhead fitting, M10x1, for hose 6/4 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Adjustable straight fitting, Sealing cone, 360° rotating, Nut M16x1.5 i., Pipe exterior Ø 10 mm, PN max. 315 bar, galvanised steel

Stoppers 290, ET, R 1, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Feather key DIN 6885 version A 8 x 7 x 60 mm material C45
Material: C45K.Version A.
Article ID: 61815600

EV02F – EV05M General features
Potentiometer to select the linearized heating curve (external temperature-water delivery temperature) with adjustable gradientfrom 0.25 to 4.5.
Potentiometer for the regulation of the comfort ambient temperature with parallel translation of the heating curve.
Potentiometer for the regulation of the economy ambient temperature with parallel translation of the heating curve.
A six-position switch to select the operating program: OFF – antifreeze – always reduced – ON – night reduced/day comfort (automatic) – night antifreeze/day comfort (automatic)
Switch for selecting the adjustment type: burner ON-OFF control – proportional-integral control (PI) of the motorized mixing valves with completely electronic feedback.
Potentiometer to regulate the stop delay of the circulation pump.
Indicator light.
Quartz clock with charge reserve of 100 hours.
Transparent protection cover.
Unit weight 1.02 Kg.
Electric features
Consumption: 5 VA.
Output through relays on voltage-free terminals.
Contacts rating: 5A – 230Vca (resistive load).
RC group protection against radio interference.

Polyurethane timing belt HTD 14M width 85mm 14M-85 open length PAZ = Polyamide fabric on tooth side
Material: Thermoplastic polyurethane (TPU), white, with steel tensile member. With green polyamide fabric on the tooth side. Temperature range -30º to +80ºC. TPU PAZ belts can be welded to endless belts (tensile force -50%). The polyamide fabric reduces the friction on aluminium or steel plates to approx. 50%. On plastic sliding plates, the friction reduction is approx. 30%. So, depending on the application, the needed driving power is much lower. By the fabric, the wear resistance of the belt is much higher and the noise is lower. Application: for example supported transportation belt drives.
Article ID: 17766501

Spur gear made of plastic PA12G with steel core module 2.5 30 teeth tooth width 25mm outside diameter 80mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 23255030

Plastic pipe PA 12, »speedfit«, blue, Operating temperature -60 °C to 100 °C, PN at 20 °C max. 15 bar, Hose Ø 15x12, Length 100 m
Resistant to corrosion, vibration, impact, ageing, high pressures and heat.

Double threaded nipple, G 1 1/4 o., G 1/2 o., AF 50, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Soft PVC workshop hose set, Safety coupling, Temperature max. 60 °C, Hose Ø 19x12.7, PN at 20 °C max. 12 bar, Length 10 m
Highly flexible hose for compressed air applications in workshop areas. Assembled with brass stem and brass quick disconnect coupling DN 7.2 optional with pushbutton safety coupling DN 7.4 and galvanised steel stem.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Blocking valve pressure gauge, Taps - tension sleeve, DIN 16270, A shape, stainless steel 1.4571, G 1/2, PN 400 bar, max. 200 °C
Used as shut-off or reducing elements for pressure gauges when measuring liquids, gases or steam.

Nipple for couplings I.D. 5.5, ARO 210, hardened / galv. steel, G 1/4 IT, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Straight screw-on fitting, G 1/2 i., for hose 8/6 mm, AF 24, Working pressure max. 18 bar, nickel-plated brass

Y- angled piece fitting »Blue Series« rotating, G/R 3/8 i./o., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.