Push-in T-connector, Plug nipple 12 mm »Blue Series«, unequal, for hose exterior Ø 10 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

1/3 Tube fitting, G 3/4 x 16 mm, taper seat, with collar, heavy-duty type, Brass with a bare metal surface

Reducing piece POM, Supports 28 mm, for hose exterior Ø 15 mm, Working pressure max. 10 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Straight push-in fitting »Blue Series«, round, M5 o., for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Triphasic servomotor (3-400V)

Length : 560 mm
SVM-N-158x32-0500-F-F1M
SKU: SVMN030500
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

ECVUSBO General features
The USB optical head is a device that allows data collection based on Fantini Cosmi family products.
The USB transceiver ECVUSBO must be used together with the Fantini Cosmi’s ECVSW PC Tool for data collection running on a PC with Windows OS.
1 free USB port
Operating System: Windows 8 Windows 7, Windows Server 2003 SP2, Windows Server 2008, Windows Server 2008 R2, Windows Vista SP 1, Windows XP SP3

Star knob GV similar DIN 6336 Technopolymer PA6GV ø40 M8
Material: Thermoplast Polyamide PA6 GV, glass-fibre reinforced, impact resistant, black matt. Bush: Steel, zinc-plated, chromated blue. Version E = with tapped blind hole d2.
Article ID: 66144000

Chain tensioner SPANN-BOX® size 1 short high tensioning force 12 B-2
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040427

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 8.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Female connector, G 1/2 i., Pipe exterior Ø 12, PN max. 315 bar, a/f1 22, a/f2 27, galvanised steel
Female connector, parallel thread, light type

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 3/8, Input pressure max. 16 bar, 0.1-2 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

Closing nipple locking on both sides, Bright brass, G 3/4 IT, I.D. 13, Operating pressure max. 100 bar, Temp. -20 °C to 100 °C
Hydraulic couplings, both sides sealing, for liquid media acc. to ISO 7241, B Series.

Areas of application: machine and plant engineering, manufacturing industry, chemical / pharmaceutical industry, automotive, food technology.

Elbow 1, Long, 90°, IT/ET, Rp/R 1, Operating temp. -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

2/3 Tube fitting, G 3/4 x 16 mm, swivel nut, lightweight CH type, Brass with a bare metal surface

Pressure gauge- screw connection, Sealing cone, G 1/4 i., Nut M14x1.5 i., Pipe exterior Ø 8 mm, PN max. 315 bar, galvanised steel
Pressure gauge fitting with cone seal, parallel female thread

Coupling package for blocking several components, incl. O-ring, for »multifix-mini«, Size 0, G 1/8 and G 1/4

Beam coupling LA made from stainless steel max. torque 36Nm overall length 66.67mm outer diameter 38.1mm both sides bore 12mm
Material: 1.4305.

- torsionally rigid design.

- zero backlash.

- perfect transmission of torque.

- very low restoring force.

* Please regard the operating factors. See PDF-catalog pages. ** Shaft
must not pushed in any further. 1) Against surcharge.

Article ID: 60299846

Triphasic servomotor (3-400V)

Suitable for belt width : 600 mm
RHP-F204A06-060-FSD-BA
SKU: RHAF20060000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

K12C General features
Cable composition:– 2 conductors x 1.5 mm²– PVC sheath– Nickel-chromium heating element– Internal splicing point– Silicone insulation
Maximum room temperature powered 40 °C
Minimum installation room temperature -20 °C
Minimum storage room temperature -20 ÷ -25°C
Maximum length of the heating circuit  from the supply point 160 m
Electric features
Power supply 230V-50Hz
Constant power delivered ~10W/m

Worm wheel made of bronze module 2 50 teeth single-thread right hand
Material: G-CuSn12, with milled out, hollow teeth. With double-sided hub. Single-thread worm gears to be paired with single-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,50. Not self-locking.

Article ID: 30132000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 11 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Quick relief valve »lineonline«, Controlled venting, Hose - thread, G 3/8, for hose Ø 8 mm, Operating pressure 1-10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 3/8, Input pressure max. 16 bar, 0.1-1 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

Wear part set, for pressure regulator DRV 200, Standard design, G 3/4

Bushing 270, IT/IT, Rp 2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in L-fitting »Blue Series« mini, rotating, R 1/8, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Angled bulkhead fitting, Pipe exterior Ø 10 mm, PN max. 315 bar, AF1 19, AF2 22, AF3 14, galvanised steel
Bulkhead elbow connector, light type

Locking screw, Hexagonal socket, without flange, G 3/8, AF 8, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Beam coupling LA made from stainless steel max. torque 36Nm overall length 66.67mm outer diameter 38.1mm both sides bore 16mm
Material: 1.4305.

- torsionally rigid design.

- zero backlash.

- perfect transmission of torque.

- very low restoring force.

* Please regard the operating factors. See PDF-catalog pages. ** Shaft
must not pushed in any further. 1) Against surcharge.

Article ID: 60299848

Feather key DIN 6885 version A 8 x 7 x 25 mm material C45
Material: C45K.Version A.
Article ID: 61814800

Triphasic servomotor (3-400V)

Suitable for belt width : 600 mm
RHP-F219A06-060-RSD-BA
SKU: RHAF22060000
Stock *: 0
Diameter: 219 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Z20A – Z30A General features
Female threaded connections ISO 7/1.
Suitable for hot and cold water, antifreeze up to 50% of the volume.
Valve body in stamped nickel-plated brass.
Stainless steel ball and pin.
PTFE seals.
Pin sealing in EPDM.
TEFZEL regulation disc.
Equal percentage regulation feature, no leakage, sealed closing (ports A-AB).
By-pass B-AB linear feature, flow rate consists 70% of the Kv, leakage of about 1 ÷ 2% of the Kv according to the standards DIN 3230 (ports A-AB) (3 ways).
Servocontrol cover in thermoplastic material.
Manual operation through the handle and manual/automatic control button.
Position indicator with reversible scale.
Protection class: I.
Fluid temperature: 5 ÷ 100°C.
Maximum differential pressure: 3.5 bar.
Rated torque: 10 Nm.
Electric features
Power supply: 230V 50/60Hz.
Power consumption: 3.5VA.
Power supply cable 1m – 3 x 0.5 mm².

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 11.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Straight screw-in fitting, Soft seal, G 1/8, Pipe exterior Ø 8 mm, PN max. 315 bar, Stainless steel 1.4571
Version with parallel thread and soft seal made of NBR.

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 1/2, Input pressure max. 16 bar, 0.2-4 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

Straight screw-in fitting, 9/16-18 UNF o., Pipe exterior Ø 10 mm, PN max. 630 bar, A/F1 22, A/F2 19, galvanised steel, UNF threat
Male connector, male thread UNF, heavy type

Angled pivot fitting with O-ring, G 1/8 o., for hose 5/3 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Screw-in fitting, Aluminium, for PVC braided hose 12x6, G 1/8, Temperature range -10 °C to 60 °C, PN max. 10 bar

Nipple for pushbutton safety couplings I.D. 8, ISO 6150 C, Stainless steel, G 1/8 ET, max. 16 bar, Temp. -20 °C to 200 °C

Locking screw Hexagonal socket without flange M10x1.0nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Internal gear made of steel C45 module 2 48 teeth tooth width 16mm outside diameter 131mm
Tooth quality: 8, Teeth generated.
Pressure angle 20°.
Outside-diametre tolerance in accordance with DIN ISO 2768 middle.

Article ID: 24144800

Beam coupling LA made from stainless steel max. torque 36Nm overall length 66.67mm outer diameter 38.1mm both sides bore 19mm
Material: 1.4305.

- torsionally rigid design.

- zero backlash.

- perfect transmission of torque.

- very low restoring force.

* Please regard the operating factors. See PDF-catalog pages. ** Shaft
must not pushed in any further. 1) Against surcharge.

Article ID: 60299850

Feather key DIN 6885 version A 8 x 7 x 45 mm material C45
Material: C45K.Version A.
Article ID: 61815300

Electric rotatory actuator multivoltage low tension

Suitable for belt width : 650 mm
RHP-F204A06-065-FSD-BA
SKU: RHAF20065000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

K20A, K30A, K40A General features
Cable composition:– 1.25 mm² conductors– Self-adjusting conductive core– Polyolefin insulating sheath– Braided copper sheath– Outer sheath in modified polyolefin
Minimum installation room temperature -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Cable dimensions– 12.6 x 4.8 mm series K20A– 14.6 x 4.8 mm series K30A-K40A
Electric features
Power supply 230V-50Hz
Tolerance -0/+5 W
Power delivered– K20A 20 W/m at 10°C– K30A 30 W/m at 10°C– K40A 40 W/m at 10°C

Worm wheel made of bronze module 1.5 50 teeth double-thread right hand
Material: G-CuSn12, with milled out, hollow teeth. With double-sided hub. Double-thread worm gears to be paired with double-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,49/0,65. Not self-locking.

Article ID: 30122000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 3.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Quick relief valve »lineonline«, with silencer, Hose - thread, G 1/4, for hose Ø 8 mm, Operating pressure 1 - 10 bar
Exhaust can be silenced by a stainless steel silencer or conveyed using a push-in fitting with an air exhaust device.

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 3/8, Input pressure max. 16 bar, 0.5-10 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

3/2-way valve, Pneumatic, monostable, Connection G 1/8, NC, Operating pre. 2.5 to 10 bar, Operating temp. -10 °C to 60 °C

Push-in T-fitting »metallica«, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Straight push-in fitting »Blue Series«, G 1/8 i., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Reducing sleeve 246, Rp 2 IT, R 1 ET, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight screw-in fitting, »value line«, G 1/8 o., for hose 5/3 mm, AF 14, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2.5 32 teeth tooth width 25mm outside diameter 85mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23295032

Shaft collar DIN 705 A set screw with slot bore 3mm zinc plated
Light-duty series. With set screw DIN EN 27 434 made from steel, zinc-plated. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62388003