Straight push-in connector, reducing, for hose exterior Ø 14/12 mm, Working pressure max. 20 bar, Stainless steel 1.4404
For use in more aggressive environments and corrosive media.

5/2-way valve, Pneumatic, »4A«, bistable, M5, Operating pressure 1.5 - 8 bar, Temperature range max. 70 °C
5/2-way pilot valves
- Pneumatic -

Push-in T-connector, Plug nipple 12 mm »Blue Series«, red., unequal, for hose exterior Ø8 mm, Working pressure max. 15 bar plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Worm thread - hose clamp »blow line«, Stainless steel (W 5) 1.4401, Belt width 12.0 mm, Clamping range 32.0 - 50.0 mm

Pipe double nipple, G 1/2, Length 120 mm, Working pressure max. 10 bar, Medium / ambient temperature max. 90 °C, Bright brass

Straight reducing supports, for hose I.D. 3/2 mm, brass
Tube connectors for polyamide hoses and polyurethane hoses made of brass CW617N and acetal copolymer (POM).

Triphasic servomotor (3-400V)

AD22 General features
Housing made of pressed stainless steel
Float made of stainless steel AISI 304.
Floating connection made of stainless steel AISI 430.
Connections between the float and the level control made in stainless steel AISI 316
Output connections with brass cable glands G 3/8.
Storage and transport temperature: -25 ÷ 70 °C.
Unit weight: 1.2 Kg.
Electric features
SPDT microswitch.
Electrical connection with 6.35 Faston (supplied).

conical seat DIN6319 PTFE-coated inner-Ø 12mm outer-Ø 21mm
Material: Steel, bright, turned, case hardened, hardening depth min. 0.2 mm. PTFE coated, blue-coloured. The very low friction enables precise adjusting at high wear resistance. * max. statical load. ** total height, together with spherical washer DIN 6319.
Article ID: 65598510

Chain tensioner SPANN-BOX® size 1 short high tensioning force 10 B-2
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040426

Neoprene timing belt HTD 14M width 40mm Lw 1400mm 100 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17711400

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 1.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Pipe double nipple, R 1, Length 80 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Pre-filter »FUTURA-mini« with PC container, 0.3 µm, Size 0, G 1/4, PE 1.5 - 12 bar, Temp. -10 °C to 50 °C, Semi-automatic
Pre-filters in modern design for compliance with strict compressed air purity requirements.
Pre-filters are used to separate solid impurities up to 0.3 µm from compressed air and gases.

Pivoting bearing block, »TF« type for standard cylinder »SE«,»SAI«,pistonØ63-80, in connection with pivoting head fastening »FTC«
Hinge bracket model, »TF« type (only in conjunction with hinge head model, »FTC« type)

Push-in T-connector, Plug nipple 12 mm »Blue Series«, unequal, for hose exterior Ø 10 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series«, rotating, Rc 1/8 i., for hose exterior Ø 10 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Kamlok quick-connect socket with interior thread, D type, Aluminium, G 1 1/4, for plug Ø 45 mm, Pressure max. 16 bar, max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Reducing nipple short type G 3/8 o., G 1/8 i. AF 19 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Clamping bush MSA bore 45mm
Material: Steel.

Mechanical, all-steel clamping elements, containing no hydraulic pressure medium. Both inner part (1) and outer part (2) have a cylindrical buttress thread with a lengthwise slot. The inner ring (3) connected to the inner part (4) has threaded studs, that create a tensioning effect when tightened.The bushes are designed for very high loads in radial as well as in axial direction. The axial runout does usually not exceed 0,02 mm. If a clamping bush without slot on the outside part is to be welded onto a workpiece, we would ask you to contact us first. Feather key grooves in the shaft do not cause any problems; simply remove the frictional corrosion.

Tolerance: Shaft h11 up to k6, Hub H7 up to H11

The values for the maximum transmittable torque and the maximum permissible axial force for the clamping bush at static load are stated in the table above. With dynamic load these values have to be reduced, i.e. divided by the operating factors listed in the adjoining table.

Operating factor: See PDF-catalog page.

1) approximate surface pressure between clamping bush and hub.




Article ID: 61504500

Triphasic servomotor (3-400V)

K20A, K30A, K40A General features
Cable composition:– 1.25 mm² conductors– Self-adjusting conductive core– Polyolefin insulating sheath– Braided copper sheath– Outer sheath in modified polyolefin
Minimum installation room temperature -35 °C
Maximum room temperature powered 65 °C
Maximum room temperature not powered 80 °C
Minimum storage room temperature -20 ÷ -25°C
Cable dimensions– 12.6 x 4.8 mm series K20A– 14.6 x 4.8 mm series K30A-K40A
Electric features
Power supply 230V-50Hz
Tolerance -0/+5 W
Power delivered– K20A 20 W/m at 10°C– K30A 30 W/m at 10°C– K40A 40 W/m at 10°C

Shaft collar DIN 705 A set screw with slot bore 3mm black finishing
Light-duty series. With set screw DIN EN 27 434 made from steel with black oxide finish. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62389003

Chain tensioner SPANN-BOX® size 1 short low tensioning force 08 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040335

SKF cylindrical roller bearing NJ 209 ECP single row inner diameter 45mm outer diameter 85mm width 19mm
Material: Bearing steel. Cylindrical roller bearings in premium-quality. - For high radial load. - Displaceable in both directions (type NU) or in one direction (Type NJ). - Usable for high speed, with groove and 3 lubribation holes. - Easy to mount (the inner ring is loose). Temperature range: -30°C to +90°C (for short time up to +110°C). Other versions or other bearing types on request.
Article ID: 64775096

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 2.5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Kamlok quick-connect plug with exterior thread, F type, Stainless steel 1.4401, R 1 1/4, Plug Ø 46 mm, Pressure max. 16 bar
High-quality, robust, universal coupling system with a safety clamp for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok stainless steel couplings are designed for use with corrosive media in the chemical and petrochemical industries, steelmaking, shipbuilding, agriculture, etc.

All female threaded couplings and connectors are with female thread sealing ring made of PTFE.

Microfilter »FUTURA-mini«, PC container, 0.01 µm, Size 0, G 1/4, Input pressure 1.5 - 12 bar, Temp. -10°C to 50°C, Semi-automatic
Micro-filters in modern design for compliance with strict compressed air purity requirements.
Micro-filters are used to separate solid oil, water and solid impurities as small as 0.01 µm from compressed air and gases.

Pivoting suction pad attachment »flexolink«, G 1/4 IT, G 1/4 ET, Steel / rubber, Bracket 12°, Bending moment 10 N
Flexible suction pad mounting

By flexing in all directions, this mounting allows the suction pad to better adapt itself to sloping workpieces.

Advantages:
Very good adaptation to sloping workpiece surfacesAutomatically resets into the initial positionVacuum-tight design with integrated protection against damage

Applications:
Handling workpieces with sloping surfaces using large-area suction padsHandling large sheets of materials that may sag when liftedCan be used together with spring plungers to compensate for differing workpiece heights and uneven surfaces

Push-in T-connector, Plug nipple »Blue Series«, for hose and plug exterior Ø 12 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Extension piece, Long, G 1/8 o., G 1/8 i., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Drip cap made of plastic, for mist oiler »variobloc«, Size 2, G 1/2, G 3/4 and G 1

Worm thread - hose clamp »blow line«, Stainless steel (W 5) 1.4401, Belt width 9.0 mm, Clamping range 20.0 - 32.0 mm

Clamping bush MSA bore 48mm
Material: Steel.

Mechanical, all-steel clamping elements, containing no hydraulic pressure medium. Both inner part (1) and outer part (2) have a cylindrical buttress thread with a lengthwise slot. The inner ring (3) connected to the inner part (4) has threaded studs, that create a tensioning effect when tightened.The bushes are designed for very high loads in radial as well as in axial direction. The axial runout does usually not exceed 0,02 mm. If a clamping bush without slot on the outside part is to be welded onto a workpiece, we would ask you to contact us first. Feather key grooves in the shaft do not cause any problems; simply remove the frictional corrosion.

Tolerance: Shaft h11 up to k6, Hub H7 up to H11

The values for the maximum transmittable torque and the maximum permissible axial force for the clamping bush at static load are stated in the table above. With dynamic load these values have to be reduced, i.e. divided by the operating factors listed in the adjoining table.

Operating factor: See PDF-catalog page.

1) approximate surface pressure between clamping bush and hub.




Article ID: 61504800

Trapeziodal threaded spindle DIN 103 Tr.70 x 10 x 1000mm long single-start right material C15 rolled
Material: C15, rolled.

Tolerance zone 7e.

Length sawed (length may be longer than nominal length),
edges not broken.



Article ID: 64007000

Triphasic servomotor (3-400V)

Type : 3-Axis VGM
GAUSSMETER 3 AXIS VGM
SKU: 65.0000067
Stock: 7
With a gauss meter, you measure locally - on the surface - the magnetic flux density in units of tesla, gauss, Ka/m or oersted. Flux density is a measure of the amount of magnetic flux through a surface. Goudsmit also conducts magnetic measurements on site if desired.

Measures strength of magnetic field
Deliverable from stock
Readout in various units
Accurate
Various functions

Operation

Operation

Gauss meter measurements use the Hall effect as the measuring principle. The sensor captures the magnetic flux density that is perpendicular to the sensor plane. The magnetic field generates an output voltage on the sensor, which is proportional to the product of the magnetic field strength and the induced current.


1D gauss meter

Type HG09: Basic version - 1D gauss meter

For measurement on a surface. The basic version is a one-dimensional meter (1D) equipped with a single Hall sensor which measures the flux density in one direction.   Suitable for: accurately measuring flux densities in one direction with a large range (max. 4.5 T) both static and alternating fields and pulses thanks to a thin measuring probe, measurements very close to the surface and in crevices measurements of fields where the local field orientation is known. This gauss meter is used to measure peak flux density of permanent and electromagnetic systems for inspections.


3D gauss meter

Type 3 Axis VGM: 3D gauss meter

The 3D meter allows you to measure magnetic fields in a free space. This gauss meter is equipped with three Hall sensors, which measure the flux density in three directions (x, y and z).   Suitable for: measuring relatively low flux densities in three directions and the ensuing results - up to max. 80 mT; scanning magnetic fields with a set alarm level. Application examples: determining safe distances in connection with exposure to static magnetic fields (medical implants, projectile hazards, pregnant workers); measuring residual magnetism in products, for example before and after demagnetizing; determining local field orientation of magnetic fields.

ZC4 General features
Cast iron valve body.
Bronze butterfly shutter.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure 6 Kg/cm².
Maximum operating temperature -120°C.
Protection degree IP40

Shaft collar DIN 705 A set screw with slot bore 4mm black finishing
Light-duty series. With set screw DIN EN 27 434 made from steel with black oxide finish. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62389004

Chain tensioner SPANN-BOX® size 1 short high tensioning force 08 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040435

SKF cylindrical roller bearing NJ 209 ECP/C3 single row inner diameter 45mm outer diameter 85mm width 19mm clearance C3
Material: Bearing steel.Cylindrical roller bearings in premium-quality.- For high radial load.- Displaceable in both directions (type NU) or in one direction (Type NJ).- Usable for high speed, with groove and 3 lubribation holes.- Easy to mount (the inner ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64775396

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 5 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Distributor with 2 quick-connect couplings I.D. 7.2, Bright brass, G 1/4 IT, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
1, 2 or 3-way distributor pieces made of brass with a bare metal surface, pre-assembled with quick disconnect coupling DN 7.2.
Available with threaded connection inside or outside or nipple for adaptation into an existing quick disconnect coupling DN 7.2 to DN 7.8.

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 1/2, Input pressure max. 16 bar, 0.1-2 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

3/2-way toggle lever valve, Hose side, Push-in connector hose 8, G 1/4, PN max. 8 bar, Temp. 0 °C to 70 °C, nickel-plated brass
Manually operated toggle valves, 2/2 and 3/2-way types. For all applications where compressed air must be switched on or off quickly and easily or a cylinder operated manually. Designed as a banjo-type valve with a hollow bolt and ring piece. Suitable for screwing directly into the equipment or for panel mounting. Compact type of construction, also ideal where space is restricted.

Push-in T-connector, Plug nipple 12 mm »Blue Series«, unequal, for hose exterior Ø 8 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Fork head, for round cylinder ISO 6432, Compact cylinder, Piston Ø 20/20 - 25, Piston rod thread M8, with folding spring bolts
Fork model

Bellows suction cup, Round 1.5 folds, Material NBR, »FGA«, ø 53 mm, suitable connection nipple IT G 1/4, ET G 1/4
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Very stiff top foldSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with?uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Double threaded nipple 280, ET/ET, R 3/4, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Clamping bush MSA bore 50mm
Material: Steel.

Mechanical, all-steel clamping elements, containing no hydraulic pressure medium. Both inner part (1) and outer part (2) have a cylindrical buttress thread with a lengthwise slot. The inner ring (3) connected to the inner part (4) has threaded studs, that create a tensioning effect when tightened.The bushes are designed for very high loads in radial as well as in axial direction. The axial runout does usually not exceed 0,02 mm. If a clamping bush without slot on the outside part is to be welded onto a workpiece, we would ask you to contact us first. Feather key grooves in the shaft do not cause any problems; simply remove the frictional corrosion.

Tolerance: Shaft h11 up to k6, Hub H7 up to H11

The values for the maximum transmittable torque and the maximum permissible axial force for the clamping bush at static load are stated in the table above. With dynamic load these values have to be reduced, i.e. divided by the operating factors listed in the adjoining table.

Operating factor: See PDF-catalog page.

1) approximate surface pressure between clamping bush and hub.




Article ID: 61505000

Triphasic servomotor (3-400V)

Suitable for belt width : 650 mm
RHP-B114A06-065-RSD-BA
SKU: RHAN1106500
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

AD23 General features
Stainless steel body.
Float and connection flange in stainless steel.
Output connections with brass cable glands G 3/8.
Storage and transport temperature: -25 ÷ 70 °C.
Unit weight: 1.2 Kg.
Electric features
Rated insulation voltage  Ui 380V~
Continuous duty rated current Ith 10A

hose clamp DIN 3017-1 type W1 steel zinc plated diameter range 60-80mm band width 9mm
Material: Steel, zinc-plated (type W1). High-performance hose clamps with worm gear thread, for fixing hoses, bellows and for similar usage. Band width 9 mm. Band thickness 0.6 mm. With hexagon screw head size 7 mm, with cross recess and slot. Other sizes and versions on request.
Article ID: 63811080

Chain tensioner SPANN-BOX® size 1 short low tensioning force 12 B-2
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040327

Neoprene timing belt HTD 14M width 40mm Lw 1610mm 115 teeth
Material: Neoprene with glas-fibre tensile member. Contact surface lined with nylon reinforcement.HTD (High Torque Drive) timing belt with semi-circular teeth profile for a more constant progress of stress in the tooth profile, for the transmisssion of high loads. Temperature range -20º to +100ºC.
Article ID: 17711700

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 7 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Storz blind coupling, Chain, Aluminium, Storz size 52-C, Tappet distance 66 mm, Operating pressure max. 16 bar
High-quality series in forged aluminium. For quick and simple hose connections.
User friendly; the coupling elements are joined without damaging the seal.
Applications: Water lines, industrial plant engineering, firefighting.

Pressure regulator, continuous pressure supply »FUTURA«, incl. press. gauge, Size 2, G 1/2, Input pressure max. 16 bar, 0.1-1 bar
Diaphragm pressure regulators with self-relieving design and excellent flow rates
in modern design for mounting side by side.
By assembling two or more controllers together, it is possible to supply several working air circuits with different output pressures via a single supply line. The regulator button can be latched and locked.

3/2-way toggle lever valve, Hose side, Push-in connector hose 10, G 1/4, PN max. 8 bar, Temp. 0 °C to 70 °C, nickel-plated brass
Manually operated toggle valves, 2/2 and 3/2-way types. For all applications where compressed air must be switched on or off quickly and easily or a cylinder operated manually. Designed as a banjo-type valve with a hollow bolt and ring piece. Suitable for screwing directly into the equipment or for panel mounting. Compact type of construction, also ideal where space is restricted.