Adjustable 45° screw conn., cone seal, 360° swivel range, female nut M30x2.0 i., Pipe ext. Ø 20, PN max. 400 bar, galvanised steel

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 14x10 mm, PN at 20 °C max. 11 bar, natural (milky), Roll of 25 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Fitting 330, flat sealing, IT/IT, Rp/Rp 2 1/2,black malleable iron fitting, Operating temp. -20 °C to 200 °C, ISO 7-1
Maximum temperature and maximum operating pressure should not occur at the same time!

According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Hexagonal coupl. nut, G 3/8, sleeve size I.D. 4, I.D. 6, I.D. 9, Max. working pressure 60 bar, Max. operating temp. 150 °C

Screw-in hose connector, G 1/2 o., for hose I.D. 8 mm, AF 24, brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Dirt strainer, bright brass, Sieve insert mesh width 0.5 mm, Operating temp. -20 °C to 110 °C, G 3/4, DN 20, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Bushing with exterior hexagonal, G 1/8, AF 14, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Retaining ring DIN 471 32mm
Material: Feather steel, phosphated, oiled. External rings for
axial fixing a machine part on a shaft.

Article ID: 61743200

MAEDLER tapered roller bearing 32007X inner-ø 35mm outer-ø 62mm height 18mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 32007X-MAE

Locking assembly BAR bore 38mm
Material: Steel.

For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft. For
medium torques. Self-centering. Slight axial offset possible during
assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub
12.5µm.

Article ID: 61543800

Pneumatic actuator SINGLE RETURN GNP

Suitable for belt width : 500 mm
RHP-B114A06-050-RSD-BA
SKU: RHAN1105000
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 4.2 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Reducer, Pipe exterior Ø Female connector 28/12 mm, PN max. 160 bar, a/f1 32, a/f2 22, a/f3 41 , galvanised steel
Reducer, light type

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 14x10 mm, PN at 20 °C max. 11 bar, red, Roll of 25 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

T-connection PP, for hose exterior Ø 32 mm, Working pressure max. 16 bar
Lightweight, push-in fittings distinguished by high strength, toughness, resistance to abrasion and impact resistance - ideal for a wide range of applications.
All our push-in fittings made of POM have the following approvals:
drinking water DVGW, KTW, FDA and NSF.
Plastic and metal tubes are connected together quickly and easily. Suitable for compressed air or liquids, with good resistance to a large number of chemicals.

Extension pipe for basic air guns, Blow pipe with standard nozzle, 90 mm curved

Push-in T-connector »Blue Series« mini, reducing, for hose exterior Ø 4/3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

Foot fastening, »LB« type for short stroke cylinder »ACQ« and »ASQ«, Piston Ø 100
Foot model, »LB« type

Hexagonal counter nut, M16x1.0, AF 22, nickel-plated brass, Max. working pressure 25 bar, Max. operating temperature 150 °C
Suitable for air, water, oil, steam, etc.

Retaining ring DIN 472 37mm
Material: Feather steel, phosphated, oiled. Internal rings for
axial fixing a machine part inside a bore.

Article ID: 61763700

MAEDLER tapered roller bearing 30207 inner-ø 35mm outer-ø 72mm height 18,25mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 30207-MAE

Splined hub with flange DIN 14 KN 28X34 length 60mm red brass Rg7
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64855900

Locking assembly BAR bore 38mm QPQ-coated
Material: Steel.

- For fixing a hub on a shaft. - QPQ coated: High corrosion resistance,
improved fatigue strength, primarily food safe (further information see
below). - For medium torques. - Self-centering. - Slight axial offset
possible during assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub 12µm.
QPQ Surface Properties: Very good corrosion resistance, better
than hard chrome or chem. nickel. Corrosion resistance in the salt spray
test SS CASS in accordance with DIN 50021. Layer thickness of 10 - 25 µm
possible. For medium operational demands we recommend a layer thickness
of 15 µm at a 90 minute treatment. Only very small changes in dimensions
(only 5 µm), as the surface modification is achieved through diffusion
and not application. Surface hardness same as clamping set material =
350 HV. Improved wear resistance, no fretting corrosion, no cold shut.
Increased endurance strength, sometimes up to 100% higher. Is completely
safe to use with food as long as there is no contact with any acidic
substances with a pH-value of = 4.

Article ID: 61573800

Pneumatic actuator SINGLE RETURN GNP

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Spur gear made of polyketone die-cast with hub module 0.5 40 teeth tooth width 3mm outside diameter 21mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28104001

Chain tensioner SPANN-BOX® size 1 long high tensioning force 20 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040609

Precision double universal joint WDR DIN 808 bore 16H7 stainless steel 1.4301 total length 125mm outer diameter 29mm
Material: Stainless steel 1.4301. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques only amount to 90% of the single precision universal joints, stainless. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199732

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 2.6 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Straight screw-in fitting, R 1/4 o., Pipe exterior Ø 12 mm, PN bar 100, A/F1 19, A/F2 17, galvanised steel
Male connector, conical male thread acc. to ISO 7-1, very light type

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 14x10 mm, PN at 20 °C max. 11 bar, yellow, Roll of 25 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Soft PVC workshop hose set, Quick-connect coupling I.D. 7.2, Hose Ø 11x6.3, PN at 20 °C max. 15 bar, Length 10 m
Highly flexible hose for compressed air applications in workshop areas. Assembled with brass stem and brass quick disconnect coupling DN 7.2 optional with pushbutton safety coupling DN 7.4 and galvanised steel stem.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Push-in T-fitting »click-clock«, rotating, G 1/4 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Reducing nipple, Long type G 1/2 o., G 1/2 i., AF 24 Nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Foot fastening, »LB« type for compact cylinder »ACP«, Piston Ø 100
Foot model, »LB« type

Rem. double threaded nipple, con. seal.R 3/8 o., R 3/8 o.nickel-plated brass, Max. working pressure 25 bar, Max. oper. temp. 150°C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

MAEDLER tapered roller bearing 30307 inner-ø 35mm outer-ø 80mm height 22,75mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 30307-MAE

Pneumatic actuator SINGLE RETURN GNP

Length : 500 mm
SVM-N-204x55-0500-B-F1M
SKU: SVMN020500
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

EV83 General features
Alphanumeric display and 4 functional keys for parameters easy setting.
Data setting via menu.
Digital weekly programmer clock with charge reserve of approximately 5 years.
Anticondensation probe for boiler protection.
Three points control output for mixing valves with servocontrol type: O24 – O34 – O35.
Three points control output for motorized mixing valves type: Z20 – Z30 – ZL30 – Zl31.
Electric features
Power supply: 230Vca 50Hz.
Consumption: 3 VA.
3 output relays.
Contacts rating: 5A-230Vca (resistive load).

Spur gear made of polyketone die-cast with hub module 0.7 20 teeth tooth width 6mm outside diameter 15,4mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28202001

Chain tensioner SPANN-BOX® size 1 short low tensioning force 06 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040331

Precision double universal joint WDR DIN 808 bore 16H7 with keyway DIN 6885-1 tolerance JS9 on both sides stainless steel 1.4301
Material: Stainless steel 1.4301. Max. Operating Angle 90°. These single and double universal joints feature a simple design with very small tolerances and high precision and performance. These universal joints can be used at speeds up to max. 800 rpm. The torques only amount to 90% of the single precision universal joints, stainless. At an operating angle of 45° only manual operation is possible. Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199732N

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 6 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Quick connector

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 14x10 mm, PN at 20 °C max. 11 bar, blue, Roll of 25 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Foot fastening, Aluminium profile, for piston rod-free cylinder, Piston Ø 32, 1 piece with 2 screws
Foot model

Push-in L-fitting »Blue Series«, rotating, G 1/2 o., for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Double threaded nipple, Conical, R 1/2 a., R 1/2 a., AF 22, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Male elbow, NPT 3/8 o., Pipe exterior Ø 8 mm, PN max. 315 bar, a/f1 17, a/f2 17, galvanised steel
Male elbow, NPT thread, light type

Hexagonal coupling nut, G 1/2 left, for sleeve size I.D. 13, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.
Dimensions may vary slightly.

MAEDLER tapered roller bearing 32008X inner-ø 40mm outer-ø 68mm height 19mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 32008X-MAE

Pneumatic actuator SINGLE RETURN GNP

Length : 460 mm
SVM-N-158x32-0400-F-F1M
SKU: SVMN030400
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Intellitouch CH193WIFI General features
WiFi connection for remote control through APP Intelliclima+ for Smartphone and Tablet.
Wireless connection: Wi-Fi 2,4 GHz (802.11 b/g);
ON / OFF boiler control (settable from the main menu).
Protection degree: IP20;
Acoustic signals: buzzer feedback with key pressing;
Perpetual clock calendar, with backup battery;
Software Class A;
Minimum differential: ±0.1K;
Thermal gradient: 4K/h;
Maximum ambient temperature: 45 °C.
Electric features
Power supply: 230V-50Hz;
Electrical insulation: double insulation
Pollution degree: 2;
Pulse voltage: 4000V;
Connection: 3 screw terminals (contact switching NC and NO);
Type of action: 1BU (micro disconnection);

Flanged bush BBP bore 10mm polyamide 6.6 outer diameter 14mm length 10mm flange diameter 20mm
Material: Thermoplastic polyamide 6.6, die cast. Color: natural.Polyamide is very well suited for the manufacture of plain bearings due to its good sliding characteristics and strong wear resistance even at dry-running conditions and because of its sufficient mechanical strength and excellent corrosion resistance. Surface pressure max.: 18 N/mm², dependant on sliding speed and bearing temperature Sliding Speed:2 m/s Lubrication: usually not required Bearing clearance: about 0.01 mm per mm shaft-Ø Bearing temperature: Should not exceed 80°C. With thin-walled parts, the frictional heat is dissipated extremely well. Coefficient of linear expansion: 8 x 10^-5 Moisture absorption max.: 7.5% Moisture absorption at 20°C and 50% rel. humidity: 2.4% Mounting hole: tolerance H7
Article ID: 62381200

Chain tensioner SPANN-BOX® size 1 short high tensioning force 06 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040431

Clamp collar double-split stainless steel 1.4305 bore 60mm with bolts DIN 912 A2-70 type N
Material: Stainless steel 1.4305, screws stainless steel A2-70. Typ N: with keyway DIN 6885-1. The thread of the screw DIN 912 is covered with a layer of nylon.Tolerance b: +0.08mm / -0.25mm. Temperature range: -40ºC to +175ºC. Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores.
Article ID: 62399460N