Rod end GT-R DIN 12240-4 series K internal thread M20x1.5 left maintenance-free stainless steel
Material: Outer part: Stainless steel 1.4057, forged. Inner ring:
Stainless steel 1.4034, hardened, ground and polished. Bearing race:
Stainless steel 1.4571 with PTFE-Lining.

Wide version. Dimensions according to DIN 648 / 12240-4 series K. Thread
either right-handed or left-handed.
Heavy-duty rod ends for high radial loads in corrosive areas.

Stainless steel on PTFE-lining.

Maintenance-free.

Article ID: 63299720

2/2-way solenoid valve brass, NC, pilot operated, 230 V, 50 - 60 Hz, Medium temperature -20 °C to 85 °C, Rp 3/4, PN 0.35 - 9 bar
Standard series, proven over many years, available in three different versions

- Directly operated
- Combined operation
- Pilot-operated

For all applications with compressed air, neutral gases or low-viscosity, neutral media.

Screw-in hose connector G 1/8 o. for hose I.D. 8 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Polyurethane hose (PUR), Temperature -20 °C to 60 °C, Hose Ø 10x8 mm, PN at 23 °C max. 7 bar, black, Roll of 25 m
Polyurethane hoses are renowned for their extreme flexibility and correspondingly narrow bending radius across a wide temperature range.

They are more flexible even than LD-PE hoses and exhibit good abrasion resistance, very good low-temperature flexibility, only minimal permanent deformation when subjected to long-term stresses as well as good resistance to the majority of oils, greases, aliphatic hydrocarbons and oxygen.

Main applications:
- Pneumatic and hydraulic (miniature hydraulics) lines
- Mechanical engineering
- Engine construction
- Instrumentation and control
- Suitable for vacuum
- Ideal for use with unions

Adjustable union elbow, with cone seal, 360° swivel range, female nut M36x2.0 i., Pipe ext.Ø 25, PN max. 400 bar, galvanised steel

Quick-connect coupling I.D. 7.2, bright brass, G 3/8 IT, Operating pressure 0 - 35 bar, Med./ambient temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Push-in bulkhead L-connector »Blue Series«, M12x1, for hose exterior Ø 4 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Worm thread hose clamp, Steel bright galvanised (W1), Clamping range 292.0 - 327.0 mm, Belt width 20.0 mm
Worm-drive type.

Extremely robust hose clamps for all applications where heavy loads occur and high forces are transmitted.

Hexagon-head screw slotted, a/f 13, bright galvanised steel, passivated blue.

Sintered bronze silencer, flat, G 1/8 o., Operating pressure max. 10 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

MAEDLER tapered roller bearing 30204 inner-ø 20mm outer-ø 47mm height 15,25mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 30204-MAE

Clamping bush E bore 60mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61596000

Pneumatic actuator DOUBLE ACTING GNP

Length : 410 mm
SVM-N-158x32-0350-F-F1M
SKU: SVMN030350
Stock *: 0
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

ODUSB General features
ODUSB interface connects the system with all the devices that can communicate through a USB port. It isused for the system configuration through the software “MiA-Make” or for the connection to “MiA-SMART” tosupervise and control the whole system.
Multiple interfaces can be connected simultaneously to the bus.
Electric features
Power supply by Bus 24Vcc – 20mA

Hexagon nut DIN 934 steel strength 8 zinc plated fine thread M10x1mm right handed
Material: Steel, tensile strength 8, zinc-plated.Hexagon nuts according to the old standard DIN 934 with metric ISO fine thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65251000

Internal gear made of steel C45 module 1.5 80 teeth tooth width 15mm outside diameter 150mm
Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.

Article ID: 22848000

Service unit 3-part »variobloc«, PC container and protective cage, Size 1, G 1/4, Input pressure max. 16 bar, Temp. max. 50 °C
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure, with self-relieving design, combined with a centrifugal separator and a proportional lubricator.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Hood with on / off switch

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 40, Stroke 5, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjust. angled screw conn., 360° swivel range, cone seal, female nut M16x1.5 i., Pipe ext. Ø 10, PN max. 315 bar, galvanised steel

Quick-connect coupling I.D. 7.2, bright brass, G 1/2 ET, Operating pressure 0 - 35 bar, Med./ambient temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Double threaded nipple 245, ET/ET, red., R 1, R 1/2, oper. temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in connector 45°, Plug nipple 8 mm »Blue Series«, for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Straight screw-in supports, R 1/4 o., for hose I.D. 5 mm, AF 14, Over-pressure max. 10 bar, Temperature range -40°C to 90°C, PA 6
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

MAEDLER tapered roller bearing 30304 inner-ø 20mm outer-ø 52mm height 16,25mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 30304-MAE

Ready-to-install flange nut Tr.24 x 5 single-start right material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Single-Thread, right handTolerance zone 7H.
Article ID: 64477124

Pneumatic actuator DOUBLE ACTING GNP

Extension cable 100 m
DEMAG EXTENSION CABLE 100m
SKU: E0068570
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Star knob similar DIN 6336 type GV Technopolymer PA6GV ø40 M8x30
Material: Thermoplast Polyamide PA6 GV, glass-fibre reinforced, impact resistant, black matt. Threaded bolt: steel, zinc-plated, chromated blue.
Article ID: 66144030

Chain tensioner SPANN-BOX® size 1 long high tensioning force up to 06 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040601

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 1.6 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Straight push-in fitting, Exterior hexagonal, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 20 bar, Stainless steel
For use in more aggressive environments and corrosive media.

Compact cylinder LINER, ISO 21287, double-acting, Piston Ø 40, Stroke 5, G 1/8, Working pressure max. 10 bar, Temp. -10°C to 60°C
New series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 8, Stroke 30, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Quick-connect coupling I.D. 7.2, bright brass, G 1/4 IT, Operating pressure 0 - 35 bar, Med./ambient temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

T-connection, for hose 6/4 mm, AF 9, Working pressure max. 18 bar, nickel-plated brass

Nipple for pushbutton safety couplings I.D. 8, ISO 6150 C, Stainless steel, G 1/4 ET, max. 16 bar, Temp. -20 °C to 200 °C

Sintered bronze silencer, Slot, G 1/8, Operating pressure 0 - 8 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

MAEDLER tapered roller bearing 32005X inner-ø 25mm outer-ø 47mm height 15mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 32005X-MAE

Ready-to-install flange nut Tr.24 x 5 single-start left material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Single-Thread, left handTolerance zone 7H.
Article ID: 64477424

Pneumatic actuator DOUBLE ACTING GNP

Belt type : 3 mm Polyurethane, green, 94° Shore
RECE-CB-10-X-PU-30
SKU: 45.1800041
Stock: 1
Suitable for belt width: 1000 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

AD23 General features
Stainless steel body.
Float and connection flange in stainless steel.
Output connections with brass cable glands G 3/8.
Storage and transport temperature: -25 ÷ 70 °C.
Unit weight: 1.2 Kg.
Electric features
Rated insulation voltage  Ui 380V~
Continuous duty rated current Ith 10A

Chain tensioner SPANN-BOX® size 1 long high tensioning force 08 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040605

Ready-to-install flange nut Tr. 24 x 10 P5 double-thread right hand material red brass
Material: Red brass Rg7 (CuSn7Zn4Pb7-C).Ready-to-Install Flange Nuts with Metric ISO-Trapezoidal Thread DIN 103, Double-thread, Right HandTolerance zone 7H.
Article ID: 64577124

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 2.7 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Screw-in hose connector G 1/8 o. for hose I.D. 6 Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Short stroke cylinder, single-acting, Magnet, Piston Ø 40, Stroke 10, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 8, Stroke 40, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Quick-connect coupling I.D. 7.2, bright brass, G 1/2 IT, Operating pressure 0 - 35 bar, Med./ambient temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Distributor, 2-fold, R 1/4 exterior, Outlets 2 x G 1/4 IT, nickel-plated brass, Max. operating pressure 60 bar, Max. Temp. 150 °C
Distributors, 2 outlets, nickel-plated brass

Pivoting bearing, »TM« type for standard cylinder »SE«,»SAI«, piston Ø32, only in connection with pivoting head fastening »FTC«
Hinge model, »TM« type (only in conjunction with hinge head model, »FTC« type)

Double threaded nipple, G 1/8 o., G 1/8 o., AF 14, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Chain connecting link type 11 / E for roller chain similar to 05 B-1 NP pitch 8mm nickel-plated packing unit 5 pieces
Similar to DIN ISO 606 (ex DIN 8187).Material: Special Chain Steel, Nickel-Plated. Sizes 20 B-1 and 24 B-1 with cottered pin.* Packing units of 5 pieces.
Article ID: 10066803

MAEDLER tapered roller bearing 30205 inner-ø 25mm outer-ø 52mm height 16,25mm
Material: Bearing steel.Standard tapered roller bearings in high quality.- For common axial and radial load.- Usable for low speed to middle speed.- Easy to mount (the outer ring is loose).Temperature range: -30°C to +90°C (for short time up to +110°C).Other versions or other bearing types on request.
Article ID: 30205-MAE

Pneumatic actuator DOUBLE ACTING GNP

Set counter flanges + O-rings Hydrohansu Ø250 mm | Hygienic
SET HYDROFORM CONTRA FLANGES/O
SKU: E0103986
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

ZDEV General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Possibility to connect a pressure gauge to monitor gas pressure (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Chain tensioner SPANN-BOX® size 1 long high tensioning force 10 B-1
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040606