Precision spur gear made of steel 16MnCr5 module 3 18 teeth bore 20mm hardened and ground outside diameter 60mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24381820

Blocking valve pneumat. actuated, double-acting, NC, nickel-plated brass, Temp. -20°C to 150°C, Control pressure 3-8 bar, Rp 1
2/2-way check valves, specially designed for automated industrial plant engineering.
A low-price, compact, space-saving and reliable alternative to ball valves with a pneumatic rotary actuator.
These valves have a full bore and - owing to the optimised design - only minimal flow losses.
They are controlled by means of filtered compressed air.

Protective cage, for »variobloc«, Size 2, G 1/2, G 3/4 and G 1

Spiral hose, Fitting and kink protection spring, PU, G 1/4, Hose Ø 8x5, PN at 23 °C max. 12 bar, Length 10.0 m
Standard type or with braided reinforcements for high pressures.

These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Screw-on hose connector G 1 1/2 i., for hose I.D. 50 nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Adjustable male connector, M20x1.5 o., Pipe exterior Ø 14, PN 630, a/f1 27, a/f2 27, galvanised steel

2/3 Tube fitting, G 3/4 x 13 mm, swivel nut, taper seat, heavy-duty type, Brass with a bare metal surface

Sealing cone assembly, for pressure regulator for water, G 1/2

Stoppers 290, beaded, R 1 ET black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Clamping bush E bore 24mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592400

Suitable for belt width : 400 mm
RHP-B114A06-040-RSD-BA
SKU: RHAN11040000
Stock *: 0
Diameter: 114.3 mm
Magnet field strength (flux density) (±10%): 3000 gauss
Magnetic system: Permanent Neoflux® magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

M23 General features
Press-forged brass valve body OT58 UNI 5705.
Gaskets in NBR (Buna N) – Viton.
Rod in stainless steel AISI 304.
Core in stainless steel AISI 430F.
Spring in stainless steel AISI 302.
Antivibration brass ring.
Operating temperature: -10 ÷ 90°C.

Slide set DA 5321 slide length 300mm aluminium
Material: Slide elements: Aluminium.Ball retainers and balls: Stainless steel. Sold by pair (1 x product no. = 1 pair of slides). Telescopic ball bearing precision slides for applications in the industrial and electronics sector. Hold-in in closed position. Mounting bracket for electrical cabinets on request. Service life 40,000 cycles. Temperature range: -20°C to +70°C. Note Recommended fastening: M5 countersunk/ 6mm countersunk Euro screw. Use all mounting positions to achieve the max. load rating. The load capacity was tested at a slide spacing of 450mm. Attention: vertical (side) mounting only.
Article ID: 64904530

Spur gear made of plastic PA12G with steel core module 1.5 48 teeth tooth width 17mm outside diameter 75mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 21855048

Pressure regulator DRV 200, Standard design, non-reversible, incl. pressure gauge, G 1/2, Control range 1.5 - 8 bar
Diaphragm pressure regulators with non-self-relieving design and non-pressure-reduced single-seated valve. Very precise adjustment and good response characteristic because there are only a few moving parts and hence
minimal friction.
Ideal for compressed air, nitrogen and other neutral, non-flammable gases, but only suitable for liquids with comparatively low flow rates.

Fitting elbow 98, conical sealing IT/ET Rp 1 1/4, R 1 1/4, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Spiral hose, Fitting and kink protection spring, PU, G 1/4, Hose Ø 10x6.5, PN at 23 °C max. 11 bar, Length 6.0 m
Standard type or with braided reinforcements for high pressures.

These exceptionally elastic polyurethane hoses boast a recoil force similar to that of conventional polyamide spiral hose, but with less tendency to loop and significantly better resistance to abrasion.
There is consequently less danger of scratching coated or sensitive surfaces.
The hose is extremely flexible and non-kinking.

Pressure regulator »lineonline«, Thread (inlet) - hose (outlet), G 3/8, for hose Ø 8 mm, Operating pressure 2 - 10 bar
Particularly suitable for installation between the valve and cylinder and as a pressure regulator in secondary branches of the pneumatic system. The regulator is fitted with a pressure limiting valve for overpressure exhaust.

Straight push-in connector »Blue Series«, Self-locking, for hose exterior Ø 8 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

2/3 Tube fitting, G 3/4 x 13 mm, swivel nut, lightweight CH type, Brass with a bare metal surface

Sintered bronze silencer, Hexagonal, G 3/4, AF 32, Operating pressure 0 - 8 bar, Operating temperature -10 °C to 250 °C
For reducing the exhaust noise generated by pneumatic equipment.

Reducing nipple, short type, G 1/4 o., M5 i., AF 17, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Conical seat DIN6319 inner Ø 16,5mm outerØ 28mm for bolt diameter 14mm stainless steel 1.4401 / AISI316
Material: 1.4401.* Max. statical load.** Total height, together with spherical washer.
Article ID: 65599564

Clamping bush E bore 25mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592500

Length : 360 mm
SVM-N-158x32-0300-F-F1M
SKU: SVMN030300
Stock: 3
Type: VMN3 (with flange)
Advised max. installation height: - (n/a) mm
Neodymium magnetic plates are extremely powerful, compact and lightweight. They are suitable for separation of ferrous contaminants from 30 µm to 3 mm.Completely stainless steel and watertight. Suitable for the food industry.

Neodymium GSN-35, Br 11,200 gauss (at 20 °C), Tmax. 80 °C
Capture Fe particles from 30 µm
Manual cleaning (wipe off)
Completely stainless steel and watertight
Max. holding field 180 mm

Application

Small ferrous contaminants / lightweight / food

Neodymium magnetic plates are extremely powerful, compact and lightweight. They are used when ferromagnetic (Fe) particles smaller than 3 mm must be separated. Completely stainless steel and watertight. Suitable for the food industry.
 
You can easily hang them suspended above a conveyor belt yourself, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipe channel, we also supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
If the product comes in direct contact with the magnet, we recommend type 3; this has an extremely high field strength at the magnet yet a compact field, which also makes it ideal for capturing weakly magnetic particles, such as stainless steel scrapings. Type 2 was developed for overbelt placement or installation in a free-fall line with mounting plate.
 
* Note: If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: N-35
Completely stainless steel housing
Watertight
Smooth finished weldings
Finish: grit blasted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Working principle

Filtering & discharging of ferrous contaminants

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

Ball transfer unit 340 with steel-sheet housing ball diameter 45mm ball from stainless steel
Material Version 330: Housing: Steel, zinc-plated.  Ball cup: Steel, case hardened.  Ball: Steel, hardened. Material Version 340: Housing: Steel, zinc-plated.  Ball cup: Steel, case hardened.  Ball: Stainless steel, hardened, Material No.: 1.3541. Premium ball transfer unit, for low noise pollution and long service life. With felt seal. See also the tolerance rings: They permit more generous tolerances in the mounting hole. Conveying speed max. 2m/sec. Temperature range -30°C to +100°C. Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.
Article ID: 65434045

Service unit 3-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.1-4 bar, Fully-auto.
Three-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Adjustable union elbow, with cone seal, 360° swivel range, female nut M24x1.5 i., Pipe ext.Ø 16, PN max. 400 bar, galvanised steel

Wear part set for stainless steel casting pressure regulator and stainless steel casting filter regulator, Size 3, G 1/2 and G 3/4

Pressure regulator »lineonline«, thread (outlet) - hose (inlet), G 3/8, for hose Ø 8 mm, Operating pressure 2 - 10 bar
Particularly suitable for installation between the valve and cylinder and as a pressure regulator in secondary branches of the pneumatic system. The regulator is fitted with a pressure limiting valve for overpressure exhaust.

Straight Check valve »Blue Series«, Thread to hose, M5 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
The non-return function of these push-in fittings prevents the air from flowing back, the unidirectional design means air flow is only possible in one direction.
These valves are available with air flow from the port to the tube or from the tube to the port.

Angled screw-in fitting, R 1/8 o., for hose 6/4 mm, AF 8, Brass
For the installation of plastic tubing.

RIEGLER Spray cleaner, Removes residual oil / skin grease on parts to be glued, Before implementation use RIEGLER lock, 500 ml
Cleaner and degreaser, suitable for many surfaces (metals, glass, ceramics and many plastics). Should always be used before applying RIEGLER Lock.

Pipe double nipple 23, ET/ET, Black steel, R 1/2, Length 150.0 mm, Max. working pressure 50 bar, DIN EN 10241
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 1.5 48 teeth tooth width 17mm outside diameter 75mm
Material: Outer part: Plastic
PA 12 G. Steel core: Stainless steel 1.4305.

Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range
-60°C to +120°C, short periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 21895048

Clamping bush E bore 25.4mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592540

Intellicomfort CH180RFWIFI General features
Temperature regulation scale 2 ÷ 40 °C, increment 0.1°C.
Measurement scale/room T display 30 ÷ 70%, increment 1%.
Measurement scale/room T display – 50 ÷ + 50 °C.
Relative humidity adjustment range 0÷100%.
Differential 0.3 ÷ 5 K.
Thermal gradient 4 K/h.
Maximum room temperature 45°C.
WiFi connection 2,4 GHz.
Radio frequency 868Mhz.
Maximum radio frequency power transmitted < 10mW.
Managements general heating, cooling and humidity control.
Managements zone heating, cooling and humidity control.
Managements maximum 8 control zone.
Managements maximum management of 15 devices directly connected to the CH180RFWIFI.
Managements maximum management of 114 devices directly connected to network.
Managements alarm management to exceed minimum and maximum temperature.
Managements system lock management to overcome the minimum and maximum temperature threshold.
Managements cooling management by activating the dehumidifier through dew point control or via a predetermined UR% threshold.
Managements remote change over (only with APP).
Managements auxiliary ON / OFF control for electric users (only with CH175).
Viewing of energy consumption and system fault anomalies.
Correction of the offset of the temperature read.
Possibility to associate the names to all the zones.
Storage temperature -10°C ÷ +60°C.
Protection degree IP40.
Display: Italian, English, French, Spanish, German, Russian.
Screen lock of CH180RFWIFI and the connected CH120RFs with password and for display cleaning.
Electric features
Google Play
App Store

Pillow block bearing unit BK 12 bore 12mm material steel black oxide finished
Material: Housing from steel, all surfaces machined, black oxide finished. With quality rolling bearings from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the fixed side. With two angular contact ball bearings, lightly preloaded, with seals. With 8 mounting holes. Locknut and distance bushes are included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for support side: Pillow Block Bearing BF. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64200112

Service unit 3-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.5-8 bar, Fully-auto.
Three-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Replacement sieve for dirt strainers made of stainless steel, for connection size 1

Spiral hose coupling set, Standard coupling I.D. 7.2, Polyamide, Hose Ø 8x6, PN at 23 °C max. 19 bar, Length 7.5 m
For safe and effective flow.

Thanks to their small coil diameter, they are compact, easy to handle and lightweight.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Nipple for couplings I.D. 2.7, Stainless steel 1.4404, G 1/8 ET, AF 11, Operating pressure 0 - 35 bar, Temp. -15 °C to 200 °C

Plug-in nipple push-in 8 mm, for couplings I.D. 5, nickel-plated brass, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C

Distributor, 2-fold, G 1/8 interior outlets 2 x G 1/8 IT, nickel-plated brass, Max. operating pressure 60 bar, Max. Temp. 150 °C
Distributors, 2 outlets, nickel-plated brass

RIEGLER Leak detection spray, DVGW approval, non-flammable, Works as an anti-corrosive, 400 ml
Detects cracks and porous areas in compressed air pipes quickly, conveniently and reliably. Non-flammable, anti-corrosive action. DVGW tested.

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 1/2, Length 120 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Splined hub with flange DIN 14 KN 32X38 length 60mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64899508

Clamping bush E bore 28mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592800

Length : 400 mm
SVM-N-204x55-0400-B-F1M
SKU: SVMN020400
Stock *: 0
Advised max. installation height: 120-180 mm
Height: 55 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

ZD..NC General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP65.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages: 110V AC 50/60Hz or 12V AC/DC

Clamp collar for splined hub DIN 14 KN 36x42 diameter 90mm red brass Rg7
Material: Red brass (CuSn7Zn4Pb7-C).Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05
Article ID: 64866200

Pillow block bearing unit BK 12 bore 12mm material steel nickel plated
Material: Housing from steel, all surfaces machined, nickel-plated. With quality rolling bearings from Japan. Ready-to-install housing bearing unit for trapezoidal and ballscrew spindle drives, for the fixed side. With two angular contact ball bearings, lightly preloaded, with seals. With 8 mounting holes. Locknut and distance bushes are included. Due to the standard dimensions, these units can also replace parts of other suppliers. Spindle reworking on request. Matching counterpart for support side: Pillow Block Bearing BF. Details for spindle end working, please refer to our catalog page by clicking the button below.
Article ID: 64201112

Service unit 3-part »FUTURA-mini«, Metal container, Standard pressure gauge, Size 0, G 1/4, Control range 0.5-10 bar, Fully-auto.
Three-piece service units with excellent flow rates in modern design.
Diaphragm pressure regulator with secondary ventilation.

Extension pipe without nozzle, straight 300 mm, Aluminium, for use with safety nozzles for high performance air guns

Fitting elbow 98, conical sealing, IT/ET, Rp 2 1/2, Operating temp. -20 °C to 300 °C, black malleable cast iron, Hot-dip galva.
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Angled screw-in fitting, G 1/2 o., for hose 9/12 mm, Working pressure max. 10 bar (20 °C)/max. 2.5 bar (90 °C), PP
Chemically resistant to almost all inorganic acids and bases, even in high concentrations and at temperatures greater than 90 °C.

L screw-in fitting, ET conical, R 3/8, for hose 10/8 mm, AF 12, Working pressure max. 18 bar, nickel-plated brass

Worm thread hose clamp, Stainless steel 1.4401 (W5), Hexagonal screw AF 7, Clamping range 32.0 - 50.0 mm, Belt width 9.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, Stainless steel 1.4401 (W 5).

Strainer for check valves, G 2 1/2, Filter Stainless steel 1.4301, Plastic thread, Operating temperature -20 °C to 100 °C

Cross-connection supports, for hose I.D. 4 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.