Chain KE similar to 08 B-1 plastic with stainless steel
Similar to DIN ISO 606 (ex DIN 8187).Material and type:Type KE: Inner links made from special polycarbonatewith high chemical resistance, for food industry or labority.Outer links from stainless steel 1.4301.Type KE-Eco: Similar to KE, but inner links from standardpolycarbonate, with lower chemical resistance.Main dimensions according to DIN.Very light and silent running.Very clean due to closed surfaces on the inner link.High corrosion resistance.Long lifetime, without any lubrication.Breaking load significantly higher than pure plastic chains.Temperature range -10°C to +80°C.Vmax 70m/min.Sold by meter. Connecting links have to be ordered seperately.
Article ID: 10555000

Clamping bush E bore 15.875mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61591587

ZC4 General features
Cast iron valve body.
Bronze butterfly shutter.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure 6 Kg/cm².
Maximum operating temperature -120°C.
Protection degree IP40

Lifting eye nut DIN 582 M8 steel C15E galvanized ================================================== Actual user information is available on the internet in the section Downloads =================================================
Material: Steel C15E zinc-plated.For lifting and transport activities.For security areas and high requirement.For permanent attachment to transport parts.With CE marking und user information.Temperature range: -20°C to +200°C.

Article ID: 65458708

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 0.9 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Bushing 270, IT/IT, Rp 2 1/2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

3/2-way solenoid valve »lineonline« silenced venting, Hose - thread, G 1/4, Hose Ø 8, NC, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Straight push-in connector with plug nipple 12 mm, reducing, for hose exterior Ø 10 mm Working pressure max 20 bar Stainless steel
For use in more aggressive environments and corrosive media.

Angled piece 90°, interior / interior, Rp 3/4, Operating pressure max. 20 bar, Operating temp. max. 175 °C, Stainless steel

Straight screw-on fitting, »value line«, G 1/2 i., for hose 8/6 mm, AF 24, Operating pressure max. 18 bar, nickel-plated brass
Straight connectors
Nickel-plated brass, »value line« Series

Coupling package for blocking several components, incl. O-ring, for »multifix«, Size 4, G 3/4 and G 1

Locking plug »click-clock«, Plug nipple 5 mm, Working pressure max. 16 bar, Operating temp. -20 °C to 80 °C, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 1.5 64 teeth tooth width 17mm outside diameter 99mm
Material: Outer part: Plastic
PA 12 G. Steel core: Stainless steel 1.4305.

Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range
-60°C to +120°C, short periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 21895064

Clamping bush E bore 19mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61591900

Locking assembly BAR bore 40mm
Material: Steel.

For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft. For
medium torques. Self-centering. Slight axial offset possible during
assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub
12.5µm.

Article ID: 61544000

Length : 700 mm
SVM-F-304x99-0700-B-F0E
SKU: SVMF050700
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

OCS1 General features
Operating temperature -20 ÷ 40 ° C
Max. Of applicable motors 10
Motor power supply time max. 3 min.
Electric features
Power supply 230Vac 50Hz
Voltage of centralized control signal 12 V.d.c.
Maximum current for each output 5A
Protection fuses 2 x 3.15A F

Protective cap for clamping bolt M 8
Material: Hexagon Bolt: DIN 933, steel, strength class 8, zinc-plated. Hexagon nuts: DIN 934/DIN 936, steel, zinc-plated. Protective cap: Neoprene 85° Shore hardness, black. Note: protective cap has to be ordered separately. This protective cap is elastic and can be easily slipped over the bolt head.

Article ID: 67600048

Flexible coupling EL nominal torque 40Nm long version with pilot bore overall length 95mm outer diameter 45mm
Material: Hubs 11 SMn Pb 37, from Ø 55 mm CK45. Spring: Spring steel type C. These couplings are elastic all-metal couplings and completely maintenance free. The all-metal design leads to a strong resistance against oil and higher temperatures: -40°C to +100°C. The elastic part consists of a spring body, made up of three layers of wound springs welded into the connecting hubs. The couplings are suitable for both rotating directions. They can be locked against rotation with a feather key or with pins. The couplings are pressfitted. Demounting is done by pressing or pulling off. Vibrations and shocks are largely absorbed. Depending on the length of the coupling - S, L or Db - bending of 3 - 6° or axial displacement of 3 - 6% of the nominal shaft diametre are possible. Couplings are available pre-drilled ex stock. Customized bores and feather-key grooves available at surcharge.
Article ID: 60204100

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 0.7 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Quick-connect coupling I.D. 7.2, nickel-plated brass, Sleeve 9 mm rotating, Operating pressure 0 - 35 bar, Temp. 0 °C to 70 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

3/2-way solenoid valve »lineonline« silenced venting, Hose - thread, G 1/4, Hose Ø 8, NO, 24 V DC, Operating pressure 2.5 - 7 bar
Though small in size, these valves are solenoid-piloted and feature very high performance.
Each valve comes complete with a monostable manual control and LED. Exhaust can be damped with a silencer or conveyed via a pipe fitting.
Function corresponds to the normal position of the valve.

Straight screw-in fitting, M27x2 o., Pipe exterior Ø 25 mm, PN max. 400 bar, A/F1 46, A/F2 41, galvanised steel
Male connector, metric thread, heavy type

Closing cap, Octagonal, G 1, AF 40, Working pressure max. 20 bar, Stainless steel 1.4408

Screw-in hose connector, G 1/2 o., for hose I.D. 6, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Check valve, DN 20, Brass, Metallic sealing, Operating temperature 0 °C to 90 °C, G 3/4, PN max. 16 bar
Applications: Water (no steam), neutral and non-corrosive liquid media, mineral oils.

Only suitable for liquid media. Flap valve closes by gravity, therefore only possible to be installed horizontally!

Push-in cartridge »Blue Series«, can only be pressed in plastic, for hose exterior Ø 8 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Clamping bush E bore 19.05mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61591905

Splined hub with flange DIN 14 KN 46X54 length 100mm steel C45
Material: Steel C45Pb, from diametre 70 C45. Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0,05mm
Article ID: 64851400

Locking assembly BAR bore 40mm QPQ-coated
Material: Steel.

- For fixing a hub on a shaft. - QPQ coated: High corrosion resistance,
improved fatigue strength, primarily food safe (further information see
below). - For medium torques. - Self-centering. - Slight axial offset
possible during assembly.
Fit, Surface: Due to the special design of the BAR clamping set
even rough fits can be bridged with excellent self centering capacity.
Shaft and hub up to Quality h8/H8. Surface finish for shaft and hub 12µm.
QPQ Surface Properties: Very good corrosion resistance, better
than hard chrome or chem. nickel. Corrosion resistance in the salt spray
test SS CASS in accordance with DIN 50021. Layer thickness of 10 - 25 µm
possible. For medium operational demands we recommend a layer thickness
of 15 µm at a 90 minute treatment. Only very small changes in dimensions
(only 5 µm), as the surface modification is achieved through diffusion
and not application. Surface hardness same as clamping set material =
350 HV. Improved wear resistance, no fretting corrosion, no cold shut.
Increased endurance strength, sometimes up to 100% higher. Is completely
safe to use with food as long as there is no contact with any acidic
substances with a pH-value of = 4.

Article ID: 61574000

Length : 1100 mm
SVM-F-204x92-1100-B-F0E
SKU: SVMF041100
Stock *: 0
Type: VMF4
Advised max. installation height: 70-110 mm
Interface/connection dim's: Threaded hole M8 (8x)
Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C.They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.

Magnet quality ferrite GSFD-33 (Br 4100 gauss)
Capture Fe particles from 0.5 mm
Manual cleaning (wipe off)
Max. temp. 100 °C
Max. holding field 140 mm

Application

Ferrous contaminants > 0.5 mm / heavy / non-food

Ferrite plate magnets are cost-effective, yet less powerfull and larger than neodymium plate magnets. They have the advantage that they can be used up to 100 °C. They remove ferrous contaminants from 0.5 mm. Not suitable for weakly magnetic stainless steel contamination.
 
Select your magnet size on the desired holding field depth. The deeper the field should reach, the heavier and larger magnet you have to select. For this reason it can be wise to select the more compact and strong neodymium (Neoflux®) plate magnets.
 
Placement
You can easily hang them suspended over a conveyor belt, attach them to the wall of a product channel, or mount them under a passing product stream. For dust-tight installation against the wall of a free-fall pipeline, we supply neodymium plate magnets including a mounting plate and quick-cleaning mechanism (see chute magnets).
 
* When placing above a belt, make sure that the construction directly below the magnet consists of non-magnetic material.

Design

Construction & materials data

Click on a product variant to find the data sheet, drawings and other downloadable product information.
 
Summary of important specifications

Magnet quality: ferrite GSFD-33
Material cap: stainless steel
Material contact plate: Steel
Finish: painted


Options

Available versions, options & accessories

Click on a product variant to find the online available accessories & spare parts.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually by wiping, or through use of a hinged extractor plate for quick-cleaning. You can swing the hinged extractor plate away from the magnet. The ferrous particles fall off of the extractor plate as soon as they are moved far enough away from the magnet.
 
For plate magnets including mounting plate and hinged cleaning construction: see also 'chute magnets'.

ZL30 General features
Controlled fluid: cold and hot water with max 50% glycol volume, superheated water and steam.
Fluid temperature controlled 5 ÷ 120 ° C.
High closing point (▲).
Stainless steel shutter.
Stem in stainless steel.
EPDM O-ring stem seal.
Flow rate characteristic: regulation port A – AB: equal percentage (VDI / VDE 2173) n (gl) = 3; bypass B – AB: linear (VDI / VDE 2173).
Leakage rate: regulation port A – AB: max 0.05% of Kvs; bypass B – AB: max. 1% of Kvs value.
External thread in accordance with ISO 228.
Red Rg5 stamped brass valve
Nominal pressure 1600 kPa.
Differential pressure Δpmax 400 kPa.

Polyurethane hose PU, color natural outer diameter 4mm, inner diameter 2,5mm
Material: Polyurethane. Dimensions and tolerances to DIN 73378. Max. length 100m. Application: Pneumatic-tube for Pneufit-Push-In or Pneufit C connectors. Pu-tubes allow only a lower pressure than Pa-Tubes, but they need a smaller radius. Max. Operating Pressure: The pressures shown in the table are valid for -40°C up to +20°C. At higher temperature note follwing factors: Temperature 30 °C: Factor 0,83. Temperature 40 °C: Factor 0,72. Temperature 50 °C: Factor 0,64. Temperature 60 °C: Factor 0,57 (max. operating temperature).

Article ID: 86990401

Ball transfer unit 363 size 45 stainless steel
Material Type 363: Stainless steel. Light duty ball transfer unit for medium high load. Orientation: Ball up or horizontal. Size 22 and 30 with felt seal. Without drain hole. Can be used with fixing clip. Conveying speed max. 1m/sec. Temperature range -20°C to +70°C. Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.
Article ID: 65436345

Worm wheel made of bronze module 1.5 40 teeth double-thread right hand
Material: G-CuSn12, with milled out, hollow teeth. With double-sided hub. Double-thread worm gears to be paired with double-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,49/0,65. Not self-locking.

Article ID: 30121800

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 0.6 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Joint head, »UNIT« type, for compact cylinder »ACP«, Piston Ø 12, Piston rod thread M3x0.5 i., without lubrication nipple
Rod eye model, »UNIT« type (incl. threaded adapter)

Short stroke cylinder, double-acting, Magnet, Piston Ø 25, Stroke 30, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Compact cyl.ISO 21287, double-acting, female piston rod, magnet, PistonØ20, Stroke70, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Long reducer, Soft sealing, G 1 o., G 3/4 i., PN max. 400 bar, AF1 41, galvanised steel
Reducing adapters, galvanised steel acc. DIN 2353

Strainer for check valves, G 1 1/4, Filter Stainless steel 1.4301, Plastic thread, Operating temperature -20 °C to 100 °C

L-multi-distributor 2-fold »click-clock«, rotating, G 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Straight push-in fitting »Blue Series«, Self-locking, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Clamping bush E bore 20mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592000

Magnet width : 920 mm
MAGNETIC SWEEPER W920 RMS3
SKU: SEMV092020
Stock *: 0
Type: RMS3 - manually operated
Magnetic system: Permanent ferrite magnet
Magnetic brooms sweep up iron and steel parts from clean or rough floors or sandy surfaces. In short, in places where iron is not or very difficult to sweep together or is not visible, such as in sand.The brooms collect metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds. Fast and easy cleanable.

Push manually or tow as a trailer
Permanent magnet
Magnet width 300-1600 mm
Quick cleaning through use of extractor plates
Engineering, production & service

Application

Sweeping floors to clean them from iron particles

Magnetic brooms (magnetic sweepers) 'sweep up' iron particles from clean or rough floors or sandy surfaces. They work well in areas where it is very difficult to sweep up iron (or just the iron and nothing else) or it is not visible, such as in sand.
 
The strong magnet in the broom collects metal debris, such as nails, screws, nuts, chips and grinding dust in workshops, factory halls, festival areas, exhibition halls and on paved or sandy parking lots or camping grounds.

Types

We have standard types and 'specials' available

In addition to the standard magnetic brooms on this page, we are happy to make a special broom for you on request. Other dimensions or attachments for forklift forks or trailers, etc.

Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Cleaning (iron disposal)

Cleaning & discharging of caught iron particles

Bar magnet type
The bar magnet has a scraper ring, with which you can slide the captured iron particles to the side. There the iron automatically falls from the bar housing.
 
Plate magnet type
This type of magnetic broom contains a strong plate magnet with a hinged separator plate (extractor plate) in front. After the floor has been swept the separation plate can be swung away, causing the iron particles to automatically fall off. It can then easily be swept up with a dustpan and broom.

Sicurgas P73 General features
Shockproof insulating material casing.
Internal visual and acoustic alarms.
Additional acoustic signal.
Sicurgas has three warning lights: green LED – indicates that the detector works properly, yellow LED – indicates detector failure, red LED – indicates the gas presence in the environment (ALARM).
Semiconductor sensor for carbon monoxide detection.
Admissible humidity (without condensation): from 30 to 80% UR.
Unit weight: 0,41 Kg.
Electric features
Power supply: 230Vac 50Hz.
Consumption: 3 VA.
Output through electromagnetic relay.
Contacts rating: 5(3)A – 250Vac.

Polyuerthanschlauch PU, color black outer diameter 4mm inner diameter 2,5mm
Material: Polyurethane. Dimensions and tolerances to DIN 73378. Max. length 100m. Application: Pneumatic-tube for Pneufit-Push-In or Pneufit C connectors. Pu-tubes allow only a lower pressure than Pa-Tubes, but they need a smaller radius. Max. Operating Pressure: The pressures shown in the table are valid for -40°C up to +20°C. At higher temperature note follwing factors: Temperature 30 °C: Factor 0,83. Temperature 40 °C: Factor 0,72. Temperature 50 °C: Factor 0,64. Temperature 60 °C: Factor 0,57 (max. operating temperature).

Article ID: 86990403

Ball head precision levelling adjuster with locknut MN 686.7 40-26.0 stainless steel
Material: X10CrNiS18.9, Nr. 1.4305. For non-parall surfaces up to 4° slope. Lower overall height with short adjustment travel. With lock nut. *the static net load Fadd can be calculated after subtracting the pre-load (stainless steel bolt strenght 6.8) from the total load Ftot. Other sizes on request.

Article ID: 68699750

Worm wheel made of bronze, module 1.5 40 teeth single-thread right hand
Material: G-CuSn12, with milled out, hollow teeth. With double-sided hub. Single-thread worm gears to be paired with single-thread worms. If the module (and number of threads) are matching, various ratios at various axle distances can be realized. Pressure angle 20°. Efficiency: approx. 0,49 Not self-locking.

Article ID: 30101800

Blocking valve pneumat. actuated, single-acting, NC, nickel-plated brass, Temp. -20°C to 80°C, Control pressure 4.2-8 bar, Rp 1
2/2-way check valves, specially designed for automated industrial plant engineering.
A low-price, compact, space-saving and reliable alternative to ball valves with a pneumatic rotary actuator.
These valves have a full bore and - owing to the optimised design - only minimal flow losses.
They are controlled by means of filtered compressed air.

Joint head »UNIT« type for short stroke cylinder »ACQ«/»ASQ«, Piston Ø 12, Piston rod thread M3x0.5 i., without lubrication nipple
Rod eye model, »UNIT« type (incl. threaded adapter)

Polycarbonate container, Protective cage, incl. O-ring, with fully automated bleeder valve, for »multifix«, Size 4, G 3/4 and G 1

Compact cyl.ISO 21287, double-acting, male piston rod magnet, PistonØ20, Stroke70, M5, Work.press.max.10bar, Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Adjustable male connector, M14x1.5 o., Pipe exterior Ø 8, PN 630, a/f1 19, a/f2 19, galvanised steel

Locking screw, Exterior hexagonal with collar G 1/8, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

L-multi-distributor 2-fold »click-clock«, rotating, G 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Head nut for cover / floor, for round cylinder ISO 6432 (not TP), Piston Ø 8-10, M12x1.25
Head nut for cover / base

Clamping bush E bore 22mm
Material: high-quality steel

The clamping bush consists of a double-walled steel sleeve filled with a pressure medium, and a flange part. Inside the flange there is a screw and a piston with seal to build up compression.

Function: When the thrust screw is tightened, the sleeve expands uniformly against shaft and hub, creating a rigid connection through frictional force. When the thrust screw is loosened, the bush returns to its initial position and can be easily disassembled.

Concentricity: 0,02 mm.
Tolerances:
Shaft h7 for d = 15 mm.
Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
Shaft h8 for the other diametres d.
Hub H7.

MN = transmittable torque at load of 0. If the screws are fastened with Manz.
Fa = transmittable axial force at torque of 0. If the screws are fastened with Manz.
Fr = Maximum transmittable radial force.
Manz = required fastening torque for the screws.
* with coated surface

Temperature range: -30° to +85°C.



Article ID: 61592200

EC85A General features
Pair of sensors 85mm

Internal gear made of steel C45 module 1.5 72 teeth tooth width 15mm outside diameter 140mm
Tooth quality: 8, Teeth generated. Pressure angle 20°. Outside-diametre tolerance in accordance with DIN ISO 2768 middle.

Article ID: 22847200