Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 10, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Bellows suction cup, Round 2.5 folds, Silicone material, »FG«, suitable connection nipple IT M5, ET M5 Ø5mm
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Soft, flexible foldsSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Hexagonal counter nut, G 1, AF 41, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 25 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking screw, Hexagonal socket, without flange, R 3/8, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Timing belt pulley from steel T10 96 teeth belt width 25mm for taper bush 2517
Material: Steel, phosphated.These steel pulleys offer a much higher wear resistance than standard parts from aluminium.The ready-to-install taper version enables a quick mounting and a fatigue-resistant shaft-to-hub connection.In this youtube video we show the mounting and demounting of taper bushes: Video clip (3.5 Minutes)
Article ID: 16477396

Precision single universal joint WENR stainless steel 1.4301 with needle bearing made of bearing steel bore 14H7 with keyway DIN 6885-1 on both sides
Material: Stainless Steel 1.4301 (X5CrNi1810). Needle bearings
from bearing steel.

Max. Operating Angle 45°. The needle-bearing universal joints have
almost zero backlash, high accuracy and good turning properties. These
special needle-rollers without cage can take high loads even at large
operating angles. A special grinding process realizes a perfect
parallelism of the axes and the single parts of the joints - which
guarantees an extremely long service life.
Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199126N

Electropneumatic - signal 4-20 mA with position transmitter

Suitable for belt width : 600 mm
RHP-F254A06-060-RSD-BA
SKU: RHAF25060000
Stock *: 0
Diameter: 254 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ECCS..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for hot water up to 90°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

Protective cap for clamping bolt M10
Material: Hexagon Bolt: DIN 933, steel, strength class 8, zinc-plated. Hexagon nuts: DIN 934/DIN 936, steel, zinc-plated. Protective cap: Neoprene 85° Shore hardness, black. Note: protective cap has to be ordered separately. This protective cap is elastic and can be easily slipped over the bolt head.

Article ID: 67600050

Chain tensioner SPANN-BOX® size 1 short low tensioning force 10 B-3
Material: Housing from steel, zinc-plated, black lackered. Chain rider from low pressure polyethylene PE-UHMW.These ready-to-install tensioners enable noise reduction and wear reduction at chain drives.With three springs. On choice: Two tensioning force versions. At both versions, three different forces can get activated.With colored wear-off indicator: Green: o.k. Yellow: still o.k. Red: Tensioning force too low.Usable travel up to the end of the yellow range: About 32mm. Total travel about 40mm.Interchangeable with similar parts of other suppliers.Temperature range: -20°C to +60°C (short time up to +80°C).
Article ID: 14040336

Spur gear made of plastic PA12G with steel core module 2 36 teeth tooth width 20mm outside diameter 76mm
Material: Outer part: Plastic PA 12 G with steel core. Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short periods 150°C. - Special plastic with excellent material properties. - Enables snugly fitting, high strength shaft-hub connection. - Optimal force transmission due to cylindrical contact area. - Light, silent and clean, with excellent dry running properties.
Article ID: 23155036

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 9.3 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Reducer, Pipe exterior Ø Female connector 28/15 mm, PN max. 160 bar, a/f1 32, a/f2 27, a/f3 41 , galvanised steel
Reducer, light type

Spiral hose coupling set, Safety coupling I.D. 7.4, Polyamide, Hose Ø 10x8, PN at 23 °C max. 15 bar, Length 2.5 m
For safe and effective flow.

Thanks to their small coil diameter, they are compact, easy to handle and lightweight.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 15, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Bellows suction cup, Round 2.5 folds, Silicone material, »FG«, suitable connection nipple IT G 1/8, ET M5 / G 1/8 Ø7mm
Robust and hard-wearing suction pad with a single sealing lip.

Used wherever objects (parts, packing materials, etc.) need to be lifted, transported, turned over or handled in some other manner. It is also ideal when it is necessary to compensate varying workpiece heights or uneven surfaces or to handle easily damaged parts. It acts as the connecting element between the vacuum generator and the workpiece.

Properties:
Soft, flexible foldsSoft, tapered sealing lipsSupports on the bottomHigh suction forceOptimum damping effectVery good adaptation to curved workpiece surfaces or materials with uneven surfaces

Applications:
Handling workpieces with extremely uneven surfaces (e.g. pipes)Handling easily damaged parts

Cross-connection supports, for hose I.D. 12 mm, Over-pressure max. 10 bar, Temperature range -40 °C to 90 °C, POM
Lightweight tube connectors distinguished by high strength, toughness, resistance to abrasion and impact resistance.

Resistant to the following chemicals:
Acetone, benzine, benzene, butane, alcohols, diesel fuels, crude oil, natural gas, ethanol, fruit juices, glycerine, fuel oil, hydraulic fluids, aliphatic ketones, carbon dioxide, carbonic acid, engine oils, methanol, propane, liquefied gas, lubricating oils, lubricating greases, town gas, washing liquor and water.

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 1.6 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Hose sleeve, ball nipple, hose I.D. 4, nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150 °C
Suitable for air, water, oil, steam, etc.

Precision single universal joint WENR stainless steel 1.4301 with needle bearing made of bearing steel bore 16H7
Material: Stainless Steel 1.4301 (X5CrNi1810). Needle bearings
from bearing steel.

Max. Operating Angle 45°. The needle-bearing universal joints have
almost zero backlash, high accuracy and good turning properties. These
special needle-rollers without cage can take high loads even at large
operating angles. A special grinding process realizes a perfect
parallelism of the axes and the single parts of the joints - which
guarantees an extremely long service life.
Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199132

Smart Positioner

Belt type : 2.4 mm Polyurethane, white, 94° Shore
RECE-CB-15-F-PU-24
SKU: 45.1800085
Stock: 2
Suitable for belt width: 1500 mm
Spare conveyor belts, to replace worn or damaged conveyor belts of Goudsmit eddy current, overband or high gradient magnetic head pulleys.

Fast delivery
Quick and efficient
Long service lifespan
High quality components
Prevents production downtime

ECCF..GMA General features
The specific design and the high quality execution secure a long-term measuring stability.
Meter for cold water up to 50°C
REED IPG 14 sensor to transmit remotely the water metering measures.
Protection magnetic cover.
Dry clockwork with magnetic transmission.
Rotatable register at 360°C for an easier reading.
REED cable with 1.5 mt length, not extendable.
10 litres/pulse.
Reading capacity: 9,9999 m³.
Minimum displayed value: 0,0001 m³.

Plug pin outer diameter 6mm
Material: Plastic acetal resin.

Article ID: 86110600

Linear bearing unit KG-3 ISO series 3 with closed linear ball bearing with angular compensation with double rubber seal for shaft Ø 30mm
Material: Housing made from extruded aluminium with a closed linear bearing of the ISO Series 3 from premium brand in top quality, with self-aligning capability that accommodates tilting. Lubricated ready-to-install.Recommended shaft tolerance h6. Spare linear bearing (that accommodates tilting) on request. * when mounting from the bottom side choose the next smaller screw size.

Article ID: 64673000

High performance safety valve, Vibration-proof design, Brass, Operating temp. max. 260 °C, G 3/4, AF 36, Trigger pressure 10.6 bar
Proportional, spring-loaded safety valves with a lifting device. Type-tested acc. to VdTÜV Specification for safety valves 100.
Exceptionally reliable, even when installed in extreme environments (vibration-resistant design).

Suitable for compressed air and other non-toxic, neutral and non-flammable gases that may be freely released. Not suitable for steam.

Metered air gun with standard nozzle hole 2.0 mm, Aluminium, Temperature range -10 °C to 50 °C, PN max. 10 bar, G 1/4 IT
The blowing power is steplessly adjusted by the lever action and can be increased up to the maximum level.
The blowing force can thus be individually controlled to cover a wide range of applications.

Spiral hose safety coupling set, Spark erosion protected, PUR, PN max. 10 bar, Hose Ø 10x6.5, Spiral Ø 52, Length 6.0 m
Completely installed with safety coupling and nipple NW 7.6 for demanding industrial compressed air applications.
High-quality safety coupling made of steel, able to operate with one hand, for high flow values. For demanding applications with high mechanical wear. The hose has a spark guard on the outer layer and resists flying sparks and scorching. Therefore it is optimally suited for use by compressed air tools in the area of welding work.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 10, Stroke 20, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Reducer, Pipe exterior Ø Female connector 10/8 mm, PN max. 630 bar, a/f1 17, a/f2 19, a/f3 22, galvanised steel
Reducer, heavy type

Straight screw-in fitting, M18x1,5 o., Pipe exterior Ø 12 mm, PN max. 630 bar, A/F1 24, A/F2 24, galvanised steel
Male connector, metric thread, heavy type

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 16 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Hexagonal counter nut, G 3/4, AF 32, Brass, Max. working pressure 25 bar, Max. operating temp. 150 °C

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 2 36 teeth tooth width 20mm outside diameter 76mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305. Milled, straight teeth.

Tooth quality 8e25 DIN 3967. Temperature range -60°C to +120°C, short
periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23195036

Precision single universal joint WENR stainless steel 1.4301 with needle bearing made of bearing steel bore 16H7 with keyway DIN 6885-1 on both sides
Material: Stainless Steel 1.4301 (X5CrNi1810). Needle bearings
from bearing steel.

Max. Operating Angle 45°. The needle-bearing universal joints have
almost zero backlash, high accuracy and good turning properties. These
special needle-rollers without cage can take high loads even at large
operating angles. A special grinding process realizes a perfect
parallelism of the axes and the single parts of the joints - which
guarantees an extremely long service life.
Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199132N

Worm gear type. Cast aluminium body

Suitable for belt width : 800 mm
RHP-F204A06-080-FSD-BA
SKU: RHAF20080000
Stock *: 0
Diameter: 204 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

ZC3 General features
Cast iron valve body.
Bronze rotating sector valve shaped to obtain a very precise regulation.
18/20 stainless steel shaft.
Inner seal with viton O-rings 75 ÷ 280°C.
Lever for manual control.
Operating pressure PN6.
Maximum operating temperature – 120°C.

Precision spur gear made of steel 16MnCr5 module 3 25 teeth bore 25mm hardened and ground outside diameter 81mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 24382500

Clamp collar double-split stainless steel 1.4305 bore 50mm with bolts DIN 912 A2-70 type GA
Material: Stainless steel 1.4305, screws stainless steel A2-70. Typ GA: With two axial mounting bores, with thread. The thread of the screw DIN 912 is covered with a layer of nylon.Tolerance b: +0.08mm / -0.25mm. Temperature range: -40ºC to +175ºC. Features: does not damage the shaft, stronger clamping force than with set collars, even distribution of clamping forces, easy readjustment, precision honed bores.
Article ID: 62399450GA

Multi-base plate for the way valves, Base plate for 9 valve positions, for valves connection G 1/4
Light alloy manifold bases for 2 to 10 valve positions.

Front or floor flange, ISO 21287, Piston Ø 25, with 4 screws
Front or rear flange

Short stroke cylinder, double-acting, Magnet, Piston Ø 25, Stroke 40, G 1/8, Working pressure max. 10 bar, Temp. -10 °C to 80 °C
Suitable for installation in limited spaces.
Supplied with magnet.
Suitable for filtered compressed air, lubricated (ensure continuity) or unlubricated.

Round cylinder »MI« ISO 6432, double-acting, Piston Ø 8, Stroke 50, M5x0.8, Working pressure 1 - 10 bar, Temp. -20 °C to 70 °C
These round cylinders are available in the following versions:
- »MI« Series, double-acting, Ø 8 to 25 acc. to ISO 6432
- »MI« Series, double-acting, Ø 32 to 40
- »MSI« Series, single-acting, pressureless in the retracted position, Ø 32 to 40

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

»CA« type = bottom cover with male thread – hinge model?»CM« type = bottom cover with male thread, round – hinge model

Reducer, Pipe exterior Ø Female connector 12/10 mm, PN max. 630 bar, a/f1 19, a/f2 22, a/f3 24, galvanised steel
Reducer, heavy type

Push-in L-fitting »click-clock«, rotating, G 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 16 bar, nickel-plated brass
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Standard pressure gauge, Single scale bar, Connection, rear, centric, G 1/8, Goods class 1.6, Measurement range 0 - 40 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Flat seal, (NBR with aramid fibres), for connection size (inch) 3/4, Operating temperature -20 °C to 200 °C
Maximum temperature and maximum operating pressure should not occur at the same time!

Chain connecting link type 11 / E for roller chain 05 B-1 pitch 8mm packing unit 5 pieces
According to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.* Company standard.** Packing units of 5 pieces.
Article ID: 10080300

Precision single universal joint WENR stainless steel 1.4301 with needle bearing made of bearing steel bore 20H7
Material: Stainless Steel 1.4301 (X5CrNi1810). Needle bearings
from bearing steel.

Max. Operating Angle 45°. The needle-bearing universal joints have
almost zero backlash, high accuracy and good turning properties. These
special needle-rollers without cage can take high loads even at large
operating angles. A special grinding process realizes a perfect
parallelism of the axes and the single parts of the joints - which
guarantees an extremely long service life.
Optionally without or with keyway DIN 6885-1, on both sides.
Article ID: 63199140

Worm gear type. Cast aluminium body

Suitable for belt width : 800 mm
RHP-F219A06-080-RSD-BA
SKU: RHAF22080000
Stock *: 0
Diameter: 219 mm
Magnet field strength (flux density) (±10%): 1800 gauss
Magnetic system: Permanent ferrite magnet
Magnetic head pulleys capture ferrous and weakly magnetic particles and continuously carry them away. Suitable for installation in existing belt conveyor systems, in the bulk transshipment or recycling industries for example.

Cost-effective and robust
With neodymium or ferrite magnets
Permanent magnet
Automatic cleaning (continuous)
According to your requirements

Application

Application

A magnetic head pulley, or head roller magnet, separates ferromagnetic particles, such as iron or steel, and even weakly magnetic particles (such as particles from processed stainless steel) from coarse to very fine fractions and carries them away completely automatically and continuously. This magnetic roller is built into an existing conveyor belt system as a head or tail roller. and is a cost-effective magnetic metal separator. It is important to feed the material onto the conveyor belt with the magnetic conveyor roller in a thin layer (ideally a mono-layer). Magnetic head pulleys require practically no maintenance, and because these magnets are integrated in an existing installation there are almost no extra operating and energy costs.
 
For larger layer thickness a head roller magnet can be combined with a suspension or overband magnet. In this configuration the suspended magnet draws the pieces of steel out of the upper layer and the head roller magnet draws them from the lower layers of the bulk flow. Magnetic head roller separators are particularly well suited for separation of problematic shapes such as ball bearings or batteries. They are used for:

recycling and/or recovery of ferrous metals
removing, purging or eliminating ferrous parts or weakly magnetic particles from product flows
protection of machines (prevention of damage caused by metal particles)


Placement

Placement

Keep the following in mind when integrating a magnetic head pulley:

Use of head scrapers is not possible. Otherwise iron particles would be scraped off before the magnet can separate them.
No steel components in the vicinity of the head roller magnet (such as the splitter: it must be made of a non-magnetic material). Otherwise this part will be magnetized, which has a negative impact on the separation.
The field depth of the magnet.
Type of magnet system in combination with the belt thickness. The optimal placement/position of the separation partition depends on the application.

 
Goudsmit has plenty of experience with this and will be happy to provide recommendations.

Design

Design

Magnetic head pulleys are made in standard sizes and can therefore be easily integrated into an existing installation. The shaft diameter, for example, is suitable for SNL bearing blocks, and the shaft journal (including keyway) is suitable for a standard SEW gear unit. These are global standards and therefore cover most applications. The modular design makes it easy to replace the shaft, which is ideal for maintenance and customer-specific solutions. Various versions available to meet your needs:

Belt width: 400-2000 mm
Diameters: 150-400 mm
Magnet system: both axial and radial magnet construction


Working principle

Working principle

A magnetic head pulley is a head or tail roller that is filled with magnets. This roller forms a magnetic system with a correspondingly rotating magnetic field that is active around the entire circumference. The magnetic field attracts ferromagnetic metal particles in a product flow. The conveyor belt that runs over the roller carries these particles with it to the underside of the roller. When they are no longer in range of the magnetic field they fall off the belt, where they are collected and/or carried away. For strongly magnetic particles, we can place cleats on the belt to 'push' the particles out of the magnetic field.
 
For damp or fine metal particles we fit a scraper to prevent them from sticking to the belt. The advantage of a head roller magnet is that it is a continuous system, so there is no need to stop the product flow to carry off the separated metal particles. This makes the head roller magnet very suitable for product flows with lots of Fe particles. Because the product passes very close to the magnet it is also a very powerful and effective separator.

Telecomfort CT3MA General features
Telecomfort CT3MA connected to a Fantini Cosmi programmable thermostat, via SMS messages, to change remotely the prescribed program and to read programmable thermostat’s status: measured ambient temperature, day and night set temperature, the prescribed program etc.
Connectable programmable termostats: Intellitherm C57CT-C58CT, Intellicomfort CH150 (except CH150R) and colored versions, Intellitouch CH191, CH193 and colored versions
Telecomfort CT3MA has a built-in GSM modem with an external antenna (CT3MA), provided in the package.
Automatically sends an alarm in case of need: contacts closing and/or opening alarm or in the case of a blackout.
Sensitivity: 107dBm@850/900MHz, 106dBm@1800/1900MHz
Double insulation.
Operating temperature: -20 ÷ 60°C / -30 ÷ 80°C* (* reduced sensitivity).
Indicative unit weight: 140 g.
Protection degree EN 60529: IP40 (if the device is correctly installed).
Electric features
Power supply from 10 to 20 V in DC and in alternating current (50/60 Hz).
Power consumption: 10W MAX.
Quad band: EGSM850/900/1800/1900.
Output power: class 4 (2W) for EGSM850/900, class 1 (1W) for GSM1800/1900.
Sensitivity: -107 dbm @ 850/900 MHz, -106 dbm @ 1800/1900 MHz.
Relay contacts rating: 4(2)A-250Vac.
Voltage free switching contacts.
Power supply connector – 2,5mm (AWG14).
Input/output connector – 2,5mm (AWG14).

Ball transfer unit 368 size 25,4 total height 40mm housing steel with KTL "anti-oxide" electrophoretic coating
Material: Housing: Steel, with KTL "Anti-Oxide" electrophoretic coating.  Ball cup: Steel, case hardend.  Balls: Steel 100Cr6, hardened. Heavy duty ball transfer unit for high load. High shock resistance. Very low friction. Orientation: Anyway. From size 25.4 with felt seal. With drain hole. Conveying speed max. 2m/sec. Temperature range -30°C to +160°C. * Bore size. Recommended bore tolerance: H9.Note: Due to unevenness of the running surface, there are often only three rollers carrying the weight. Therefore the chosen load rating should equal at least one third of the load. Max. distance of ball transfer units = edge length of the object divided by 2.5.

Article ID: 65436825

Pre-filter »multifix« with PC container and protective cage, 0.3 µm, Size 3, G 1/2, Input pressure max. 16 bar, Temp. max. 60 °C
For filtering out solid impurities larger than 0.3 µm.

Plug-in connector for couplings I.D. 7.2 - 7.8, Stainless steel 1.4305, Sleeve I.D. 6, Operating pressure 0 - 35 bar

Cable tie, PA 6.6, black, Band: 12.0 x 540 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.

Elbow 40, 45°, Rp 2 1/2 IT, R 2 1/2 ET, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.