Service unit 3-part »Standard« with polycarbonate container, Size 2, G 3/8, Input pressure max. 16 bar, Control range 0.5 - 10 bar
Three-piece service units consisting of a reversible diaphragm pressure regulator, independent of inlet pressure,
with self-relieving design, centrifugal separator and proportional lubricator.

Jaw coupling with hose connection, I.D. 13 (1/2"), rotating, Malleable cast iron, galvanised and yellow passivated, max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 1/2, Working pressure (pre-set) 4 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

Glycerine press. gauge »pressure line« Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0 - 6 bar/90 psi, Ø 100
Low-priced series of high-quality, glycerine-filled pressure gauges with stainless steel housing for all applications involving measurements in areas with high dynamic pressure loads and vibration levels.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

T multi-distributor, Plug connector »Blue Series«, for hose exterior Ø 5x6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Push-in L-fitting »Blue Series«, Self-locking, M5 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Reducer, Pipe exterior Ø Female connector 20/12 mm, PN max. 400 bar, a/f1 22, a/f2 24, a/f3 36, galvanised steel
Reducer, heavy type

Push-in T-fitting »Blue Series« mini, L-shape, rotating, M6, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

One-piece clamp coupling MAS both sides bore 20mm with keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. Feather Key Groove DIN 6885/1, Tolerance P9. The torques in
the table are maximum values which can only be achieved with perfect
mounting and dimensional accuracy of the shaft.

Article ID: 60099720

High performance V-belt XPA EPDM datum length 925 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290925

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:2487 W
Volume Flow:1059 m³/h
Pressure:Δp s5173 Pa
Pressure:Δp t5389 Pa
Density:43862 kg/m³
Sound Pressure:0 dB(A)

With Filter Mat P15/350S Weight:8,22

ZD..NA General features
Voltage tolerance: -15% / +10%.
Environment temperature: -15°C / +60°C.
Working pressure: 500 mbar Max.
Closing time < 1 second.
Protection degree: IP54.
Cable gland: PG 9.
Pressure inlets: G1/4” on two sides (except models with brass body).
Limit switch: by request from 3/4” to 4”.
Gas type: Air and non-aggressive gases (EN 437).
Filter: 600 μm (except models with brass body).
Electric features
Rated voltage: 230Vac – 50/60Hz or 24Vac/dc
Upon request valves are available with coils for the following voltages:-110V AC 50/60Hz-24V AC/DC-12V AC/DC

Ball knob DIN 319 Technopolymer PA6GV type C ø32 M10
Material PA: Thermoplast (Polyamide PA6 GV), glass-fibre reinforced, impact resistant, black matt.Version C = With compression-moulded thread.Size 16/M5, 20/M6, 25/M8, 32/M10 and 40/M12 is not part of the DIN 319.

Article ID: 66473210

Filter regulator »variobloc«, PC container, Protective cage and pressure gauge, Size 2, G 1, Input pressure max. 16 bar
Reversible diaphragm pressure regulators, independent of inlet pressure, with self-relieving design, combined
with a centrifugal separator.
The pressure setting can be locked by pushing the knob down.
Approved series in modern industrial design, with the following key benefits:
- Simple handling
- Convenient modular assembly thanks to innovative fasteners
- Excellent flow values

Jaw coupling with hose connection, I.D. 19 (3/4"), rotating, Malleable cast iron, galvanised and yellow passivated, max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 1/2, Working pressure (pre-set) 6 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

Glycerine press. gauge »pressure line« Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0-40 bar/600 psi, Ø100
Low-priced series of high-quality, glycerine-filled pressure gauges with stainless steel housing for all applications involving measurements in areas with high dynamic pressure loads and vibration levels.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Adapter plate for mounting standard pressure gauges (round), for pressure regulator / filter regulator »G«, Size 400 and Size 600

Push-in L-fitting »Blue Series«, Self-locking, R 1/8 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Straight screw-in fitting, G 1/2 o., for hose 9/12 mm, AF 27, Working pressure max. 10 bar (20°C)/max. 1 bar (60°C), PA
Manufactured from high impact-resistant, UV-stabilised engineering plastic, extremely resistant to weathering.
Good chemical resistance to benzine, diesel oil, fuel oil and alkalis. Not suitable for use with acids.

Push-in T-fitting »Blue Series« mini, L-shape, rotating, M6, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Two-piece clamp coupling MAT both sides bore 20mm without keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. The torques in the table are maximum values which can only be
achieved with perfect mounting and dimensional accuracy of the shaft.

Article ID: 60099820

High performance V-belt XPA EPDM datum length 932 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290932

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:2753 W
Volume Flow:1117 m³/h
Pressure:Δp s5443 Pa
Pressure:Δp t5689 Pa
Density:43862 kg/m³
Sound Pressure:89 dB(A)

Pk 100 Hk + Ag 100, 100W, 24V Dc Weight:8,64

Length : 250 mm
SVM-N-114x34-0250-B-F1M
SKU: SVMN060250
Stock *: 0
Advised max. installation height: 65-80 mm
Height: 34 mm
Powerful and compact. For dry or wet use. Often used in the recycling industry or for protection of grinding mills.

Max. installation height 180 mm
Low overall height
Completely stainless steel and watertight
For recycling or metal separation

Application

Application

Plate magnets / magnetic plates are cost-effective, robust magnets. They are suitable for filtering metal parts from free-fall product flows or products on a conveyor belt with relatively little Fe contamination. Permanent plate magnets can be easily built into existing installations. In this way they protect processing machines reliably and economically, which prevents downtime of production processes. The effectiveness of plate magnets varies from 70 to 90% iron depletion. If an even cleaner product is desired, several magnets or magnet systems can be used in succession.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.

Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

OT.. General features
Asynchronous single-phase tubular motor.
Operation with switch, button or radio using the form OCR1.
Electromechanical stroke end.
2 adjustable stroke end points.
Stroke adjustment via adjustment cams.
Exit pin with spline shaft.
Continuous operating time 4 min
Electric features
Power supply: 230V 50Hz
Type of cable: H05VVF white
Cable length: 2,5 meters
Conductor: 4×0,75 mm2

Plug with sealing ring thread G1/8A
Material: Brass, nickel-plated. Sealing ring from aluminium.
Article ID: 86590018

Compact cylinder »ACP«, double-acting, Piston Ø 80, Stroke 75, Connection G 1/8, Working pressure 1-10 bar, Temp. -20 °C to 70 °C
Characterised by a very short and compact design.

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Jaw coupling with hose connection, I.D. 25 (1"), rotating, Malleable cast iron, galvanised and yellow passivated, max. 10 bar
Universal standard coupling for compressed air lines on construction sites or in industry; standard type according to DIN 3489, used worldwide in a very wide range of applications.

- Robust couplings made of malleable iron, zinc plated and yellow chromated
- Chrome VI-free, with double safety lock
- 100% couple test and secure connection

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 1/2, Working pressure (pre-set) 8 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

L-ring piece, G 1/8, for hose exterior Ø 6 mm, Working pressure max. 15 bar, Stainless steel 1.4404
For use with aggressive media and in areas susceptible to corrosive outside
influences, in the food processing industry and in hygienic and sanitary applications.

Straight push-in fitting »metallica«, R 1/8 o., for hose exterior Ø 8 mm, Working pressure max. 16 bar, nickel-plated brass
All parts with a parallel thread are supplied with an FPM O-ring while the conical threads are coated with preCOTE 5 dispersion; all fittings in this series can thus also be used at high temperatures (medium compressed
air).

Push-in L-fitting »Blue Series«, Self-locking, R 1/8 o., for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Rem. Double threaded nipple, Interior / exterior thread, con. sealing, G 3/8, Working pressure max. 10 bar, Stainless steel 1.4408

Straight screw-in fitting, G 1/4 o., for hose 10/8 mm, AF 17, Operating pressure 0 - 10 bar, Temperature -10 °C to 60 °C, POM

Two-piece clamp coupling MAT both sides bore 20mm with keyway stainless steel 1.4305 with bolts DIN 912 A2-70
Material: Stainless steel 1.4305.

Temperature range from -40°C to +175°C. Maximum speed 4000 rpm. The
screws DIN 912 - A2-70 used in all couplings are covered with a layer of
nylon. Thus the bolts do not loosen with vibrations Bore tolerance:
+0,051 mm. Feather Key Groove DIN 6885/1, Tolerance P9. The torques in
the table are maximum values which can only be achieved with perfect
mounting and dimensional accuracy of the shaft.

Article ID: 60099920

Locking assembly COM-A stainless steel 1.4401 bore 30mm size 30-55
Material: Stainless steel 1.4401 (SS316).

Clamping bush for lower torques; not self-centering.
Fit: Shaft h8, Hub H8.
Mounting: Slightly oil the clamping set before mounting, do not
use molibdenum disulphide or grease. Tighten the screws evenly and
crosswise in several steps. Demounting: Due to the cone angle,
the clamping set is usually released once all screws have been fully
unfastened. There a three large threads cut into the front ring, which
serve to remove this ring.

Ts - Fastening Torque

T - Transmittable Torque

F - Transmittable Axial Force

P - Surface Pressure onto Hub

Article ID: 61599530

High performance V-belt XPA EPDM datum length 950 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290950

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:2766 W
Volume Flow:1119 m³/h
Pressure:Δp s5461 Pa
Pressure:Δp t5702 Pa
Density:43862 kg/m³
Sound Pressure:89 dB(A)

Pk 150 Hk + Ag 150, 150W, 24V Dc Weight:8,88

Length : 500 mm
BAR-N-23-500-25-1M6-NW-B
SKU: SBAMA100010-500
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellicomfort CH150R General features
Temperature regulation range 2 °C – 40 °C
Anti-freeze temperature regulation range 2 °C – 7 °C
Max. temperature T45
Reference thermal gradient 4 K/h
Relative humidity displayed value 20% – 90%
Electric connections Screw clamps 3.5 mm twopole jack plug
Double Insulation
Protection IP20
Micro-disconnection 1BU
Software Class A
Pollution degree 2
Impulse Voltage 4000V
Electric features
Power supply from a remote actuator CH171D via two wires.
System for maintaining the prescribed time via 2 AA 1,5 V batteries (optional).
Connections length max 100 m.

Precision spur gear made of steel 16MnCr5 module 1.5 36 teeth bore 20mm hardened and ground outside diameter 57mm
Material: Steel 16MnCr5, case hardened HRC 58 ± 2. Teeth, bores and faces ground. Tooth quality 7 e25. Pressure angle 20°. Feather Keyways in accordance with DIN 6885/1, tolerance P9. Position of keyway to tooth is not defined.

Article ID: 22883620

Short stroke cylinder »ACQ« double-acting, Magnet, Piston Ø 80, Stroke 25, G 3/8, Working pressure 1-10 bar, Temp. -20°C to 70°C
Suitable for installation in limited spaces.
Supplied with magnet.
Short-stroke cylinders in two different versions:
»ACQ« Series, double-acting, Ø 12 to 100
»ASQ« Series, single-acting, Ø 12 to 63

Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Closing cap, round, G 2, Diameter 69 mm, Working pressure max. 20 bar, Stainless steel 1.4408

Hydraulic coupling, Series B, Steel, G 3/4 IT, I.D. 19, Operating pressure max. 300 bar, Operating temp. -30 °C to 100 °C
Acc. to ISO 7241-1, B Series.

This coupling series combines an extremely small pressure drop with maximum hydraulic power transmission.
Interchangeable with all couplings and plugs manufactured according to the above standard.
The patented pressure eliminator permits disconnection even if back pressure has built up (up to 200 bar).
The pressure eliminator can be used in all applications where there is a risk of pressure build-up after the line has been separated. It allows effortless connection under pressure.
The mating part must be pressureless in order for the eliminator to function optimally.

Areas of application: chemical industry, food technology, automotive, offshore.

Compact cyl.ISO 21287, single-acting, female piston rod,retr.,magnet,PistonØ20,Stroke10,M5,Work.press.max.10bar,Temp.-20°C to 70°C
Series acc. to ISO 21287 characterised by a very short and compact design.
The standard type features a magnetic piston.
Piston rod optionally with male or female thread.
Suitable for filtered, unlubricated or lubricated compressed air.
If lubrication is used, it must be continuous.

Push-in fitting 45° »Blue Series«, rotating, G 3/8 o., for hose exterior Ø 6 mm, Working pressure max. 15 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Kamlok quick-connect plug with interior thread, A type, Aluminium, G 2, Plug Ø 63 mm, Pressure max. 16 bar, Temp. max. 68 °C
Coupling system for quick and easy connection of two hoses or for joining one hose to a machine connection.

A male part and a female part are joined together by shifting the handles.
There is no need to turn the hose!

Kamlok couplings are used for a wide range of applications in industrial plant and mechanical engineering, tank and container construction, the chemical industry, food processing, mining, refuelling systems, defence technology, etc.

Stopper, Hexagonal, G 1 1/2, AF 53, Working pressure max. 20 bar, Stainless steel 1.4408

Reducing nipple, Short design, G 3/8 ET, G 1/8 IT, AF 19, Brass, Max. working pressure 25 bar, Max. operating temperature 150 °C

Spur gear made of plastic PA12G with stainless steel core 1.4305 module 4 15 teeth tooth width 40mm outside diameter 68mm
Material: Outer part: Plastic PA 12 G. Steel core: Stainless
steel 1.4305.

Milled, straight teeth. Tooth quality 8e25 DIN 3967. Temperature range
-60°C to +120°C, short periods 150°C.

Special plastic with excellent material properties.

Enables snugly fitting, high strength shaft-hub connection.

Optimal force transmission due to cylindrical contact area.

Light, silent and clean, with excellent dry running properties.

Article ID: 23495015

Shaft collar DIN 705 A set screw with slot bore 6mm bright
Light-duty series. With set screw DIN EN 27 434 made from steel. From size d1=80mm with 2 allen screws like DIN EN ISO 4027, but strength 12.9, with offset 135°.Bright turned and kalibrated. Bores tolerance H8. Large chamfer on one side of the outside diameter. Size 9 not like DIN.Temperature range: -40ºC to +175ºC.
Article ID: 62300600

High performance V-belt XPA EPDM datum length 957 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290957

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:4273 W
Volume Flow:2217 m³/h
Pressure:Δp s4849 Pa
Pressure:Δp t5211 Pa
Density:43862 kg/m³
Sound Pressure:89 dB(A)

50 W/K, 230V Ac Weight:12

Length : 500 mm
BAR-N-23-500-25-1M8-NW-B
SKU: SBAMA100030-500
Interface/connection dim's: Threaded hole M8 (1x)
Magnet quality: GSN-42
Max. operating / product temperature: 60 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellicomfort CH150 General features
Power supply 2 AA alkaline batteries, 1.5 V
Inputs Telephone activator CT3MA and separate temperature probe
Electric connections Screw clamps 3.5 mm twopole jack plug
Double Insulation
Protection IP20
Micro-disconnection 1BU
Software Class A
Temperature regulation range 2 °C – 40 °C
Anti-freeze temperature regulation range 2 °C – 7 °C
Max. temperature T45
Reference thermal gradient 4 K/h
Relative humidity displayed value 20% – 90%
Pollution degree 2
Impulse Voltage 4000V
Electric features
Contacts rating:– 5(3)A 250Vac – CH150 version– 16(4)A 250Vac – CH150-16 version
Voltage-free switching contact.
Power supply with two 1,5 V AA alkaline batteries.
Batteries operation life more than 1 year.
Low batteries charge indication