Pipe double nipple, R 1 1/4, Length 150 mm, Working pressure max. 40 bar, Stainless steel 1.4571

Push-in T-connector, Plug nipple »Blue Series«, for hose and plug exterior Ø 4 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Replacement seal for stainless steel filter and stainless steel filter regulator, Size 4, G 1

Reducing nipple, Long type, G 1 o., G 3/4 i., AF 38, Nickel-plated brass, Max. working pressure 25 bar, Max. operating temp. 150°C
Suitable for air, water, oil, steam, etc.

Push-in T-fitting »Blue Series« mini, L-shape, rotating, M6, for hose exterior Ø 3 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Spur gear made of polyacetal resin die-cast with hub module 0.5 36 teeth tooth width 3mm outside diameter 19mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28103600

High performance V-belt XPA EPDM datum length 875 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290875

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:3666 W
Volume Flow:2436 m³/h
Pressure:Δp s3745 Pa
Pressure:Δp t4026 Pa
Density:43862 kg/m³
Sound Pressure:90 dB(A)

Pk 75 Hk + Ag 75, 75W, 24V Dc Weight:7,5

Length : 450 mm
BAR-HT-23-450-25-1M6-NW-B
SKU: SBANA100010-450
Interface/connection dim's: Threaded hole M6 (1x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellicomfort CH180-230V General features
LCD display: graphic, 7-segment symbols and digits.
LED, back timed lighting (white) display.
Minimum differential: ±0,1K
Preset differential 0,3 K
Thermal gradient: 4K/h.
Maximum ambient temperature: 45 °C
Auxiliary relay output (free voltage contacts) programable by user (external probe or alarm management)
Possibility to visualize Celsius or Fahrenheit temperature values
Protection degree: IP20
Electric features
Power supply: 230V-50Hz
Insulation class: II
Pulse voltage: 4000V
Connection: 3 screw terminals (contact switching NC and NO)
Type of action: 1BU (micro disconnection)
Software: A class

Spherical bearing DIN 12240-4-K type G without outer ring relubricateable bore 35mm outer diameter 62mm stainless steel == Initial lubrication required before use ==
Material: Inner ring stainless steel 1.4034, hardened, ground and polished.Bearing shell special brass CuZn38Al1.Dimensions according to DIN 648 / 12240-1 series K (wide version).Can be re-lubricated (from size 6mm with lubricatin hole).Initial lubrication required before useFor high sliding speed up to 60 m/min.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63399235

Valve disc for valve terminal HDM, Connection 8 mm, 2x 3/2-way, NC, monostable or 5/3-way, Centre vented
These compact valve terminals, with a maximum flow rate of 800 Nl/min, can be individually adapted to the specific conditions of each application thanks tot he wide range of functions and various input and intermediate plates.

Since each valve terminal is a customer-specific combination of a series of individual elements, the catalogue only lists the available input, intermediate and end plates as well as the different valve discs and the 25-pin multi-pole connectors.

Suitable for filtered, unlubricated or lubricated compressed air. If lubrication is used, it must be continuous.

Monostable (non-latching) version of manual control also available on request.

The operating pressure is based on the installed input plates.

Fork head, »Y« type for cylinder series »SE« and »SAI«, for piston Ø 50-63, Piston rod thread M16x1.5
Fork model, »Y« type

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 3/4, Working pressure (pre-set) 4 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

Glycerine press. gauge »pressure line« Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0-10 bar/145 psi, Ø 100
Low-priced series of high-quality, glycerine-filled pressure gauges with stainless steel housing for all applications involving measurements in areas with high dynamic pressure loads and vibration levels.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Push-in T-connector, Plug nipple »Blue Series«, for hose and plug exterior Ø 4 mm, Working pressure max. 15 bar, plastic
Push-in fittings series manufactured in plastic and nickel-plated brass.
All parts are suitable for use with hoses, tubes or pipes made of plastic and copper.

Screw-in fitting, Aluminium, for PVC braided hose 16x10, G 1/2, Temperature range -10 °C to 60 °C, PN max. 10 bar

Polycarbonate container with semi-automated bleeder valve, for filter / filter regulator »G«, Size 300, G 1/4, G 3/8 and G 1/2

Push-in T-fitting »Blue Series« mini, rotating, M3, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

Spur gear made of polyacetal resin die-cast with hub module 0.7 17 teeth tooth width 6mm outside diameter 13.3mm
Material: Polyacetal resin die-cast. Bores machined. Pressure
angle 20°. With high hardness and low friction coefficient these plastic
gears can be used in various set-ups, even under water. Note Regarding
the Machining Inside these die-cast parts are some cavities caused by
production. These parts should therefore not be drilled too deep. With
larger bores or when grooving the cavities might become visible. This
often does not affect the functionality.

Article ID: 28201700

High performance V-belt XPA EPDM datum length 882 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290882

Frequency:50 Hz
Speed:2925 1/min
Shaft Output:3540 W
Volume Flow:2382 m³/h
Pressure:Δp s3707 Pa
Pressure:Δp t3965 Pa
Density:43862 kg/m³
Sound Pressure:90 dB(A)

Weight:7,7

Length : 450 mm
BAR-HT-23-450-25-1M8-NW-B
SKU: SBANA100030-450
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellicomfort CH180 General features
LCD display: graphic, 7-segment symbols and digits.
LED, back timed lighting (white) display.
Minimum differential: ±0,1K
Preset differential 0,3 K
Thermal gradient: 4K/h.
Maximum ambient temperature: 45 °C
Auxiliary relay output (free voltage contacts) programable by user (external probe or alarm management)
Possibility to visualize Celsius or Fahrenheit temperature values
Protection degree: IP20
Electric features
Power supply without connection to the electric circuit with two 1,5 V AA alkaline batteries
Insulation class: II
Pulse voltage: 4000V
Connection: 3 screw terminals (contact switching NC and NO)
Type of action: 1BU (micro disconnection)
Software: A class

Spherical bearing DIN 12240-4-K type GD without outer ring maintenance-free bore 35mm outer diameter 62mm stainless steel
Material: Inner ring stainless steel 1.4034, hardened, ground and polished. Bearing shell stainless steel 1.4571, with PTFE-lining.Dimensions according to DIN 648 / 12240-1 series K (wide version). Maintenance-free.Suitable for high dynamic loads.Without outer ring (smaller outer diameter than version S or S...D).
Article ID: 63399335

Blocking valve pneumat. actuated, single-acting, NO, nickel-plated brass, Temp. -20°C to 80°C, Control pressure 4.2-8 bar, Rp 1
2/2-way check valves, specially designed for automated industrial plant engineering.
A low-price, compact, space-saving and reliable alternative to ball valves with a pneumatic rotary actuator.
These valves have a full bore and - owing to the optimised design - only minimal flow losses.
They are controlled by means of filtered compressed air.

L-multi-distributor 4-fold »click-clock«, rotating, M5 o., for hose exterior Ø 6 mm, Working pressure max. 16 bar
The advanced version of our highly successful push-in fittings series manufactured in nickel-plated brass.

Advantages of this new, optimised series:
Much easier connection and disconnection of the hose, even with repeated mountingCan also be used for non-calibrated hosesSuitable for vacuum operation

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 3/4, Working pressure (pre-set) 6 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

Glycerine press. gauge »pressure line« Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0-16 bar/235 psi, Ø 100
Low-priced series of high-quality, glycerine-filled pressure gauges with stainless steel housing for all applications involving measurements in areas with high dynamic pressure loads and vibration levels.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Y hose connection supports, for hose I.D. 4 mm, brass CW617N, Max. working pressure 10 bar, Max. medium/ambient temp. 90 °C

T-pivot fitting, with O-ring, G 1/8 o., for hose 10/8 mm, AF 14, Working pressure max. 18 bar, nickel-plated brass

Pipe double nipple 23, ET/ET, galvanised steel ST 37-2, R 2 1/2, Length 180 mm, Working pressure max. 50 bar
The steel fittings are made of tubular steel to DIN 2441 and boast good resistance to mechanical stresses.

Hot dip galvanised steel fittings are completely coated with a layer of pure zinc and are therefore protected against rust.

They are used in pipe construction, plumbing and gas installations as well as a wide range of industrial applications, especially in conjunction with the popular malleable iron series.

Push-in T-fitting »Blue Series« mini, L-shape, rotating, M3, for hose exterior Ø 4 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

High performance V-belt XPA EPDM datum length 900 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290900

Locking assembly COM-B stainless steel 1.4401 bore 19mm size 19-27
Material: Stainless steel 1.4401 (SS316).

Self-centering clamping bush for small hub diametres. For low torques.
Self-locking. No axial movement during mounting.
Fit: Shaft h8. Hub H8. Mounting: Slightly oil the clamping
set before mounting, do not use molibdenum disulphide or grease. Tighten
the screws evenly and crosswise in several steps.
Demounting: Remove all tensioning screws and screw them into the
(usually unused) forcing thread of the front flange, until the flange is
released.

Article ID: 61599619

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:1997 W
Volume Flow:946 m³/h
Pressure:Δp s4619 Pa
Pressure:Δp t4824 Pa
Density:43862 kg/m³
Sound Pressure:86 dB(A

With Filter Mat P15/350S Weight:7,8

Length : 450 mm
BAR-HT-23-450-25-2M6-NW-B
SKU: SBANA100020-450
Interface/connection dim's: Threaded hole M6 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

FF71A General features
Case in shock-proof plastic with self-retaining screws
AISI 301 stainless steel flexible blade (50 x 165 mm)
Electric connections on Faston 6.3 (provided)
Calibration screw for adjusting the cut-in point
PVC flange, 5 mm thick
Compliance with standards CEI EN 60730-1.
SPDT single-pole switching microswitch
Electric features
Rated insulation voltage Ui 380V~
Continuous duty rated current  Ith 10A

hose clamp DIN 3017-1 type W1 steel zinc plated diameter range 23-35mm band width 9mm
Material: Steel, zinc-plated (type W1). High-performance hose clamps with worm gear thread, for fixing hoses, bellows and for similar usage. Band width 9 mm. Band thickness 0.6 mm. With hexagon screw head size 7 mm, with cross recess and slot. Other sizes and versions on request.
Article ID: 63811035

Profile damper TA 98-40 diameter 98mm thread M16
Material: Co-Polyester Elastomer. The profile damper TA are maintenance-free, self-contained damping elements. Due to the degressive damping characteristics it provides a very high energy absorption at the beginning of the stroke. The excellent temperature characteristic of the material provides consistent damping performance over a temperature range of -40°C to +90°C. The low installed weight, the economic price and the long operating life of up to 1 million cycles makes this an attractive alternative to hydraulic end position damping, if the moving mass does not need to stop in an exact datum position and it is not necessary to absorb 100% of the incoming energy. The life cycle is up to 20 times longer than for urethene dampers and up to ten times longer than for rubber springs. Environment: Resistant to oil, grease seawater and to microbe or chemical attack. Excellent UV and ozone resistance. Material does not absorb water or swell. Dynamic Force Range: 870 N to 90,000 N. Temperature Range: -40°C to +90°C. Energy Absorption: 58% to 73%. Material Hardness: Shore 55D. Mounting: in any position. Impact Velocity range: up to max. 5 m/s Mounting Bolt Torque: M3: 1 Nm. M4: 2 Nm. M5: 4 Nm. M6: 6 Nm. M8: 20 Nm. M12: 50 Nm. M16: 120 Nm. On request: special strokes, characteristics, spring rates, sizes and materials. Download Energy Stroke Characteristics 1.6 MB 1) Max. energy capacity per cycle for continuous use. 2) For a single cycle, e.g. an emergency stop.
Article ID: 69109800

Linear ball bearing unit KG-1 ISO series 1 with shields for shaft diameter 25mm stainless
Material: Housing made of extruded aluminium with a stainless steel linear bearing of the ISO Series 1 from premium brand in top quality. Either with integral double-lip seal or with shields. Lubricated ready-to-install. Recommended shaft tolerance h6. * when mounting from the bottom side choose the next smaller screw size.A = with shields. B = with seals.
Article ID: 64699525

PVC hose, Transparent, Temperature -15 °C to 60 °C, Hose Ø 22x18, PN short time loading at 20 °C max. 3.5 bar, Roller length 50 m
Food-grade PVC hose in conformity with EU Regulation No. 10/2011.
Unbeatably flexible hose for non-pressurised conveying of a wide variety of liquids such as fruit juices, mineral water, alcoholic beverages (up to 50% vol. at +40 °C), dairy products, diluted acids and alkaline solutions.
Advantages of the hose:

- Optimally visible media transport
- Extreme flexibility
- Good medium resistance

Protective pipe for screw-in, with set screw, G 1/2, L1 = 100 mm, Operating pressure max. 6 bar, Copper alloy,
For bimetallic thermometers in the »High quality« series.

Inline pressure regulator, 2 x IT, with secondary venting, Pre-pressure dependent, G 1/2, Working pressure (pre-set) 2 bar
The majority of pneumatic tools are connected directly to the compressed air supply by means of a quick disconnect coupling, in other words they tend to be supplied with a higher pressure than is actually required. Which increases consumption and leads to tool overload.

Added safety is provided by the automatic self-relieving function. If the tool is disconnected from the hose, it continues to work for a short period, even though it has been switched off, owing to the residual pressure that is present on the tool side. Inadvertent operation of the tool can thus lead to serious injuries to the user (tackers or nail drivers can fire up to another ten shots).

This effect can be prevented by using the inline pressure regulators, which have a preset pressure determined by the application, thereby achieving energy efficiency and economy.

Glycerine press. gauge »pressure line« Connection radial bottom, G 1/2, Goods class 1.6, Measurement range 0-25 bar/360 psi, Ø100
Low-priced series of high-quality, glycerine-filled pressure gauges with stainless steel housing for all applications involving measurements in areas with high dynamic pressure loads and vibration levels.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Filter element 5 µm, for filter / filter regulator »GA-mini«, Size 200

Push-in L-fitting »Blue Series«, Self-locking, M5 o., for hose exterior Ø 4 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Fitting 340, conical sealing, Rp 1 1/4, Rp 1 1/4, black malleable iron fitting, operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Push-in T-fitting »Blue Series« mini, rotating, M6, for hose exterior Ø 6 mm, Working pressure max. 10 bar
Push-in fittings series manufactured in plastic and nickel-plated brass.
Space-saving miniature design.

As long as stock lasts. Subject to prior sale.
Due to stock clearing, the items are excluded from return.
The warranty obligation is not affected.

High performance V-belt XPA EPDM datum length 907 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15290907

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:1993 W
Volume Flow:946 m³/h
Pressure:Δp s4619 Pa
Pressure:Δp t4791 Pa
Density:43862 kg/m³
Sound Pressure:86 dB(A)

Weight:8,22

Length : 450 mm
BAR-HT-23-450-25-2M8-NW-B
SKU: SBANA100040-450
Interface/connection dim's: Threaded hole M8 (2x)
Magnet quality: GSN-42SH
Max. operating / product temperature: 140 °C
These very strong neodymium magnetic bars are designed to remove small ferromagnetic contaminants from your pipeline bulk streams. Our strongest types can even remove fine weakly magnetic contamination, such as stainless steel 316 wear particles. Magnetic bars are the building blocks of many magnetic filtering systems, like our magnetic grids, Cleanfow magnets and magnetic filters for pressure lines.Our magnetic bars come in various magnet qualities, sizes, interface connections, robustness, etc. All types are equipped with a waterproof welded stainless steel 316L housing, and a smoothly polished surface.

Neodymium magnets (N42/42SH/52)
Very powerful
Watertight
Length 100-600 mm
Pipe/tubing material AISI316L

Application

Filtering magnetic contaminations from product flows

These very powerful Neoflux® (neodymium) magnetic bars / magnetic rods remove very fine ferromagnetic (Fe) metal particles and even weakly magnetic particles, such as those originating from machined stainless steel and iron oxides, from product streams.
 
Magnetic bars are the building blocks for magnetic grids, Cleanflow magnets and magnetic filters.

Design

Construction & materials data

As standard, the magnetic bars have a waterproof welded stainless steel housing, which protects the magnets and pole plates in the bar from corrosion. The bars have a smooth surface that is easy to clean.

Materials - in contact with product: AISI316L (SS 1.4404)
Connections: 1 or 2 x M6 or M8
Magnet qualities:

GSN-42, Br 13,300 gauss (at 20 °C), Tmax. 80 °C. (10,700 gauss on tube Ø23)
GSN-42SH, Br 13,300 gauss (at 20 °C), Tmax. 140 °C. (10,700 gauss on tube Ø23)
GSN-52, Br 14,800 gauss (at 20 °C), Tmax. 80 °C. (11,400 gauss on tube Ø23)


Options

Available accessories & spare parts

Click on a product variant to find the online available accessories & spare parts.

Intellicomfort CH180WIFILITE General features
WiFi connection 2.4 GHz (802.11 b/g/n)
Router communication: port 1080
Temperature regulation scale 2 ÷ 40 °C, increment 0.1°C
Measurement scale/room T display – 50 ÷ + 50 °C
Differential 0,3 ÷ 5 K
Thermal gradient 4 K/h
Maximum room temperature 45°C
Maximum radio frequency power transmitted <10mW
Managements: Heating and cooling, Summer time / Standard time, Remote change over (only with APP), Summer / Winter
Viewing of energy consumption
Storage temperature -10°C ÷ +60°C
Protection degree IP40
Pollution degree 2
Display Italian, English, French, Spanish, German, Russian
Screen lock with password
Electric features
Power supply 230V-50Hz
Maximum absorbed power 5 W
Contacts rating 5(3)A 250 Vac
Type of action 1 B.U. (connection micro-switch)
Output type: 1 relay for heating and cooling systems, (3 screw clamps (closed + open)
Software Class A
Electric insulation Double insulation
Pulse voltage 4000V

Ball knob DIN 319 Technopolymer PA6GV type C ø32 M8
Material PA: Thermoplast (Polyamide PA6 GV), glass-fibre reinforced, impact resistant, black matt.Version C = With compression-moulded thread.Size 16/M5, 20/M6, 25/M8, 32/M10 and 40/M12 is not part of the DIN 319.

Article ID: 66473208

Linear ball bearing unit KG-1 ISO series 1 with double rubber seals for shaft diameter 25mm stainless
Material: Housing made of extruded aluminium with a stainless steel linear bearing of the ISO Series 1 from premium brand in top quality. Either with integral double-lip seal or with shields. Lubricated ready-to-install. Recommended shaft tolerance h6. * when mounting from the bottom side choose the next smaller screw size.A = with shields. B = with seals.
Article ID: 64699625