Hexagon nut DIN 934 steel strength 8 zinc-plated thread M8 right handed
Material: Steel, tensile strength 8, zinc-plated.Hexagon nuts according to the old standard DIN 934 with metric ISO thread.The standard DIN 934 was replaced by DIN EN ISO 4032 / 8673. Some of these nuts have different outer dimensions (width across flats and height). But the nuts DIN 934 are still used very often.
Article ID: 65200800

Clamp collar for splined hub DIN 14 KN 23x28 diameter 64mm steel C45Pb
Material: Steel C45Pb, from Ø 70 C45 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. C/d = 0,05.
Article ID: 64860300

High performance V-belt XPA EPDM datum length 1082 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291082

Frequency:50 Hz
Speed:2965 1/min
Shaft Output:8581 W
Volume Flow:4551 m³/h
Pressure:Δp s5367 Pa
Pressure:Δp t5772 Pa
Density:43862 kg/m³
Sound Pressure:91 dB(A)

80 W/K, 230V Ac Weight:24

S81 – S82 – S83 General features
Power supply from the control units P81 or P82.
Absorption: 40mA (200mA).
3 terminals of 2,5 mm² for each sensor: C (-12…24V); S (+4…20mA); A (+12…24V).
Electric features

Inner chain link type 4/B for roller chain DIN ISO 606 08 B - GL pitch 1/2x5/16" with straight plates
Similar to DIN ISO 606 (ex DIN 8187).Material: Special chain steel.
Article ID: 10500100GL

SKF spherical roller bearing 22208 E double row inner diameter 40mm outer diameter 80mm width 23mm
Material: Bearing steel. Spherical roller bearings in premium-quality. - For very high radial load and common high axial load in both directions. - Usable at angular displacement. - Usable for high speed, with groove and 3 lubribation holes. Temperature range: -30°C to +150°C (for short time up to +200°C). Other versions or other bearing types on request.
Article ID: 64776018

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 3, G 1, max. 25 bar, 0.5 - 10 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Reducing nipple, Long, M5 o., M5 i., AF 10, Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 6x4 mm, PN at 20 °C max. 13 bar, natural (milky), Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

PVC braided hose set, Quick-connect coupling, Operating temp. max. 60 °C, Hose Ø 12x6, PN at 23 °C max. 15 bar, Length 10 m
Flexible, pressure-resistant and non-abrasive standard hose, also resistant to ageing. Assembled with brass stem and brass quick disconnect coupling DN 7.2.

Not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Bushing 240, reducing, IT/IT, Rp 1 1/2, Rp 1/2, black malleable iron fitting, Operating temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight push-in fitting »universal short«, 3/8, hose-Ø 6, taper seat, Working pressure -0,99 to 20 bar, nickel-plated brass
The quick-connect fittings of the »universal short« series are true to their name and are used for the quick and simple connection of hoses. The conical sealing threads off a high degree of flexibility, as it is compatible with both conical and cylindrical threads. Thus the quick-connect fitting can be combined with a wide variety of thread types (BSPP, BSPT, NPT, NPTF, PT, PF) of standards ISO 7.1 and ISO 228. Shorter assembly ties result from the reduced thread length. The smaller hole spacing, resulting from the reduction of the width across flats, enables installation in very tight spaces. This saves time and space.

The complete sealing is also guaranteed on uneven, for example inclined, concave or convex surfaces, and with differing radii and chamfers. The special geometry of the seal enables vacuum applications.

Suitable plastic pipes: PA11, PA12, polyethylene, polyurethane (for polyurethane a hardness of 98 shore is recommended), PTFE.

Areas of application: Pneumatic automation, automotive industry, textile and packaging industry, compressed air circuits, vacuum applications.

Straight push-in bulkhead connector »Blue Series«, Self-locking, M14x1.5, for hose exterior Ø 6 mm, Working pressure max. 10 bar
The air supply is completely shut off as soon as the hose is disconnected from the union.
The flow rate is only guaranteed if the hose is securely inserted.

Worm thread hose clamp, Chrome steel 1.4016 (W2), according to DIN 3017, Clamping range 60.0 - 80.0 mm, Belt width 12.0 mm
Worm drive type.

For all standard applications where high clamping forces are normally distributed.

Hexagon-head screw a/f 7, with integrated cross-tip, bright galvanised steel, passivated blue.

Splined hub with flange DIN 14 KN 18X22 length 45mm stainless steel 1.4305
Material: Stainless steel, Material-No. 1.4305 Ready-to-install, with 4 mounting holes, match with clamp collars for splie hubs. F/d and C/d = 0.05mm.
Article ID: 64899501

High performance V-belt XPA EPDM datum length 1090 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291090

Frequency:50 Hz
Speed:2950 1/min
Shaft Output:5200 W
Volume Flow:1723 m³/h
Pressure:Δp s6263 Pa
Pressure:Δp t6617 Pa
Density:43862 kg/m³
Sound Pressure:92 dB(A

Length : 300 mm
SVM-F-304x99-0300-B-F0E
SKU: SVMF050300
Stock *: 0
Advised max. installation height: 90-140 mm
Height: 99 mm
Cost-effective. Overbelt placement or installation against a free-fall line. Often used in the recycling industry or for protection of downstream equipment.

Max. installation height 140 mm
Low overall height
With neodymium or ferrite magnets
For recycling or metal separation

Application

Application

Ferrite magnetic plates (plate magnets) remove ferromagnetic (Fe) particles as small as 0.5 mm. An advantage is that they are suitable for use at higher temperatures (250°C), but they are not suitable for capturing stainless steel scrapings.
 
The dimensions are selected based on the desired holding field depth: the deeper the field, the heavier and larger the magnet becomes. For this reason one often opts for the more compact and equally strong neodymium (Neoflux®) plate magnets.

Placement

Placement

Overbelt placement or installation in/against a free-fall line. For placement in a free-fall line Goudsmit also supplies mounting plates (see also chute magnets). This makes dust-proof mounting possible and makes them easy to clean.
 
For a width in excess of 300 mm a neodymium magnet is recommended for installation in a free-fall line. In such applications ferrite plate magnets are too heavy for manual cleaning. If you are considering overbelt placement, keep in mind that the construction directly beneath the magnet must be made of non-magnetic material.

Design

Design

Goudsmit builds plate magnets for mounting above production lines that feature 'flux control' to create a deeper holding field. These have extra magnets between the poles that cause the lines of flux to penetrate deeper into the product flow. A ridge prevents captured iron particles from being carried away again by the product flow.


Cleaning

Cleaning

Cleaning of the plate magnet is performed manually (by wiping) or through use of an extractor plate (quick cleaning). Hereby you swing the extractor plate away from the magnet. The Fe particles fall off of the extractor plate as soon as they are moved far enough away from the magnetic field. For quick cleaning, see also chute magnets.

S81 – S82 – S83 General features
Power supply from the control units P81 or P82.
Absorption: 40mA (200mA).
3 terminals of 2,5 mm² for each sensor: C (-12…24V); S (+4…20mA); A (+12…24V).
Electric features

Spur gear made of polyketone die-cast with hub module 0.5 28 teeth tooth width 3mm outside diameter 15mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28102801

SKF spherical roller bearing 22208 E/C3 double row inner diameter 40mm outer diameter 80mm width 23mm clearance C3
Material: Bearing steel.Spherical roller bearings in premium-quality.- For very high radial load and common high axial load in both directions.- Usable at angular displacement.- Usable for high speed, with groove and 3 lubribation holes.Temperature range: -30°C to +150°C (for short time up to +200°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64776318

SKF spherical roller bearing 22205 E double row inner diameter 25mm outer diameter 52mm width 18mm
Material: Bearing steel. Spherical roller bearings in premium-quality. - For very high radial load and common high axial load in both directions. - Usable at angular displacement. - Usable for high speed, with groove and 3 lubribation holes. Temperature range: -30°C to +150°C (for short time up to +200°C). Other versions or other bearing types on request.
Article ID: 64776012

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 3, G 1, max. 25 bar, 0.5 - 16 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Reducing nipple, Long, M5 o., G 1/8 i., AF 14, Stainless steel 1.4571, Max. working pressure 60 bar, Max. operating temp. 150 °C

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 6x4 mm, PN at 20 °C max. 13 bar, blue, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Straight screw-in fitting, G 1/2 o., for hose 12/9 mm, AF 24, Stainless steel 1.4571

Double threaded nipple 245, red., R 1 1/2 ET, R 1 1/4 ET, black malleable iron fitting, oper. temp. -20 °C to 300 °C, ISO 7-1
According to DIN EN 10242 (previously 2950).
Malleable iron cast fittings in black steel, non-galvanized, is the classic fitting series in connection series in piping construction. Our malleable iron cast fittings are characterized by high mechanical strength and standardized fitting technology.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Straight screw-in fitting, G 3/8 o., Pipe exterior Ø 6 mm, PN bar 315, A/F1 14, A/F2 22, galvanised steel
Male connector, parallel male thread, light type

Dirt strainer, nickel-plated brass, Sieve insert mesh width 0.05 mm, Operating temp. -20°C to 110°C, G 1/2, DN 15, PN max. 20 bar
Suitable for domestic water services, heating and air conditioning plants or compressed air systems. Not suitable for steam.

Bushing 270, IT/IT, Rp 1/2, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

High performance V-belt XPA EPDM datum length 1107 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291107

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:9961 W
Volume Flow:4551 m³/h
Pressure:Δp s5894 Pa
Pressure:Δp t6353 Pa
Density:43862 kg/m³
Sound Pressure:95 dB(A)

Adapter set from square to round AISI304 | #350-Ø350
REDUCER DN350 EN1092-1
SKU: A513_030000
Stock *: 0
Various accessories that can be added to our products as an option. Also found under the ‘Accessories' tab of the relevant article.

Quality and reliability
Fast delivery
Easy to install
Longtime use

Application

Cleaning unit application

In order to easily clean the magnet unit and to ensure operator safety, Goudsmit has developed the magnet rotor cleaning unit. It is available as an accessory with the rotating Cleanflow magnet. With this cleaning unit, the magnetic bars are easily removed from the extractor and securely placed on the tray. This keeps the magnet clean, preventing it from falling on the ground or being attracted by a steel object. The magnet is then easily accessible from all sides and therefore easy to clean. Even if the magnet unit is saturated with attracted metal particles, and the magnetic bars are therefore very difficult to remove from the extractor, this is not a problem with the cleaning unit. The tray collects the attracted iron parts.

B12AN – B12BN General features
Sensitive element with stainless steel membrane, laser welded.
Metallic frame.
Cover in shockproof thermoplastic material.
Output connections with PVC cable gland.
Female connection G 1/4 (17 mm key).
Maximum temperature of the controlled fluid: 120 °C.
Pressure switch body admissible temperature: -35 ÷ 60°C.
Storage and transport temperature: -35 ÷ 60°C.
Unit weight: 0.43 Kg B12AN.
Unit weight: 0.44 Kg B12BN.
Electric features
G1/2 cable gland in V0 self-extinguishing, shockproof thermoplastic material, code: 303298LA
IP44 protection casing IP44, code: 2593367

Spur gear made of polyketone die-cast with hub module 0.5 30 teeth tooth width 3mm outside diameter 16mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º.Usable also under water or other mediums. Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28103001

SKF spherical roller bearing 22205 E/C3 double row inner diameter 25mm outer diameter 52mm width 18mm clearance C3
Material: Bearing steel.Spherical roller bearings in premium-quality.- For very high radial load and common high axial load in both directions.- Usable at angular displacement.- Usable for high speed, with groove and 3 lubribation holes.Temperature range: -30°C to +150°C (for short time up to +200°C).Clearance C3: Greater play.Other versions or other bearing types on request.
Article ID: 64776312

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 3, G 3/4, max. 25 bar, 0.5 - 6 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Quick-connect coupling I.D. 7.2, bright brass, rigid, Connection 10x8, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
Universal, one-hand quick disconnect couplings, one side sealing, suitable for a wide range of tasks and applications!
The closed sleeve protects the coupling from dirt.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

These quick disconnect couplings are not suitable for direct attachment to pulsating tools.
We recommend using our vibration dampers, according to ISO 6150 § 7.1.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, workshops, automotive.

Polyethylene hose (LD-PE), Temperature -10 °C to 60 °C, Hose Ø 6x4 mm, PN at 20 °C max. 13 bar, black, Roll of 100 m
Low-priced, calibrated hose for use with screw fittings.
With its soft and flexible character, combined with relatively high strengths and good resistance to stress cracking, this hose is ideal for use in the following types of application:

- Flexible pneumatic lines in the low-pressure range, providing no special resistance to greases, oils or other hydrocarbons is required.
- Compressed air control lines.
- Vacuum lines (suitable for vacuum up to 10 x 8 mm).
- Supply lines of all kinds.

Straight screw-in fitting, G 1/2 o., for hose 10/8 mm, AF 24, Stainless steel 1.4571

Reducing sleeve, round, G 1/2 i., G 3/8 i., Working pressure max. 20 bar, Stainless steel 1.4408

Bulkhead fitting »value line«, M10x1, for hose exterior Ø 4 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Quick-connect coupling I.D. 2.7, nickel-plated brass, M5 IT, Operating pressure 0 - 35 bar, Temp. -20 °C to 100 °C
One-hand quick disconnect couplings, one side sealing, extremely compact with a large bore and only a small pressure drop.
To prevent injuries or a "whiplash" effect, we recommend that the plug-in nipple is held with one hand during uncoupling.

Areas of application: Pneumatic system, machine and plant engineering, measurement, monitoring and control systems, manufacturing industry, medical technology, chemical / pharmaceutical industry, automotive.

Stoppers 290, ET, R 3/4, Operating temperature -20°C to 300°C, black malleable cast iron, Hot-dip galvanised, DIN EN 10242
Acc. to DIN EN 10242 (formerly DIN 2950)

The classic - and the most popular - screw fitting series for pipe construction.
These fittings are characterized by their high mechanical strength and surface quality to DIN 2444.
They are completely coated with a layer of pure zinc and are therefore suitable for drinking water; they are also protected against rust.
These malleable iron fittings are used in machine construction, exterior lines, cold water lines and heating lines.

Working minimal temperature = -20 °C; 25 bar.
Working pressure for temperature range from -20 °C to 120 °C: 25 bar.
Working pressure for temperature range from 120 °C to 300 °C: 20-25 bar.

Internal gear made of steel C45 module 2 30 teeth tooth width 16mm outside diameter 95mm
Tooth quality: 8, Teeth generated.
Pressure angle 20°.
Outside-diametre tolerance in accordance with DIN ISO 2768 middle.

Article ID: 24143000

High performance V-belt XPA EPDM datum length 1120 mm
Material: High Performance EPDM with polyester cord. Advanced:
These raw edged, cogged EPDM-V-belts are top products with high-strength
tensile members for improved energy efficiency and drive performance. Powerful:
The transmittable power is more than double as it is at normal narrow
V-belts and more than triple as it is at classic V-belts. Maintenance-free:
Due to the minimal elongation, a retensioning is normally not requiered. Versatile
use: With good chemical resitance and a large temperature range,
these belts a ideal for force-locking drives. Existing narrow V-belts
and classic V-belts can be replaced without problems. Common V-belt
pulleys are suitable for all these three kinds of belts. Because of the
tight length tolerances, the belts can be used in sets without
measuring. Operating temperatur: -40° to +130°C.
V-belts XPA are a useful substitute for SPA and 13.
Width b = 12.7 mm.

Height h = 10 mm.

Smallest medium pulley diametre = 71 mm.

Weight per Metre 0.105 kg.

Article ID: 15291120

Frequency:50 Hz
Speed:2945 1/min
Shaft Output:7011 W
Volume Flow:1633 m³/h
Pressure:Δp s6160 Pa
Pressure:Δp t6474 Pa
Density:43862 kg/m³
Sound Pressure:99 dB(A)

Ferrite - reinforced Weakening outfeed
HRA-F-102x44-AB-0500-R-W
SKU: TBAB050054
Stock *: 0
Width: 102 mm
Height: 44 mm
Length: 500 mm
Magnetic rails are used for straight product flows or flows with side in-feed or discharge.The most suitable magnetic rail version depends on the position in the conveyor system.Various functions are possible. Magnetic rails are also available in a waterproof version.

Infeed or discharge
Constant or dissipating magnetic force
Steel or stainless steel enclosure
With neodymium or ferrite magnets

Type AA

AA: straight-ahead version

For straight product flows with constant magnetic strength.
Suitable for installation between other magnetic rails.


Type AB/AC

AB and AC: dissipating version

With dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.
The dissipating magnetic field guarantees uniform, trouble-free transition.

Type AB for installation at the end of the magnetic conveyor
Type AC for installation at the beginning


Type BA/BB

BA and BB: tapered version

With tapered design for optimal transition to a magnet roller.

Type BA for installation in front of a magnet roller
Type BB for installation behind a magnet roller


Type BC/BD

BC and BD: tapered and dissipating version

With tapered shape and dissipating magnetic field for transition from magnetic to non-magnetic transport and vice versa.

Type BC for installation in front of a magnet roller
Type BD for installation behind a magnet roller

OT.. General features
Asynchronous single-phase tubular motor.
Operation with switch, button or radio using the form OCR1.
Electromechanical stroke end.
2 adjustable stroke end points.
Stroke adjustment via adjustment cams.
Exit pin with spline shaft.
Continuous operating time 4 min
Electric features
Power supply: 230V 50Hz
Type of cable: H05VVF white
Cable length: 2,5 meters
Conductor: 4×0,75 mm2

Spur gear made of polyketone die-cast with hub module 0.7 14 teeth tooth width 6mm outside diameter 11,2mm
Material: Polyketone (PK), ivory-colored.Moulded version. Bores machined. Pressure angle 20º. Usable also under water or other mediums.Lower friction than polyacetal gears leads to much larger lifespan, even without lubrication. Much higher safety against tooth breaking, specially at longterm usage. Temperature Range: -40°C to +140°C due to the load.
Article ID: 28201401

Pressure regulator for control panel integration »Standard«, without pressure gauge, Size 3, G 3/4, max. 25 bar, 0.5 - 10 bar
Incl. panel nut and washer.

Reversible diaphragm pressure regulators, independent of inlet pressure,
with self-relieving design.

Angled piece, 45°, interior / interior, G 1, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Cable tie, PA 6.6, black, Band: 9.0 x 760 mm, Operating temperature -45 °C to 85 °C, PU 100 pcs.
Cable tie / hose tie from polyamide 6.6 for fast, seamless and reliable bundling of cables, hoses, etc.. The black cable tie offers a higher resistance to UV radiation thanks to the enclosed "soot".
Application: electrical installations, industrial cabling, automobile cabling, marine cabling, pre-fab buildings, special applications.

Counter-hinge model, ISO 15552, ISO 21287, for fork model acc. DIN 71752, Ø80
Counter-hinge model for fork model acc. DIN 71752

Angled piece, 90°, interior / exterior, G 3/8, Operating pressure max. 10 bar, Operating temperature max. 90 °C, Bright brass

Bulkhead fitting »value line«, M14x1, for hose exterior Ø 6 mm, Operating pressure max. 16 bar, nickel-plated brass
Low-priced yet very high-quality series of push-in fittings made of nickel-plated brass.
Compact, space-saving, lightweight design. An O-ring in the fillet at the end of the thread guarantees a tight connection for all male thread parts, even on rough surfaces.

Standard pressure gauge, Single scale bar, Connection radial bottom, G 1/8, Goods class 1.6, Measurement range 0 - 25 bar, Ø 40
Bourdon-tube pressure gauge in standard design.

Suitable for gaseous or liquid media which do not corrode copper alloy,
do not have high viscosity and do not crystallise.

Locking screw, Hexagonal socket and flange G 1/4 AF 6 nickel-plated brass Max. working pressure 25 bar Max. operating temp.150 °C
Suitable for air, water, oil, steam, etc.